THE WORLD MODELS Aure User manual

Wing Span
Wing Area
Flying Weight
Fuselage Length
81.5 in / 2070mm
572.0 sq in / 36.9 sq dm
3.3 lbs / 1500g
43.5 in / 1100mm
Warning !This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Radio required : 3 channels, 4 servos airplane radio
* Specifications are subject to change without notice.*
Specifications
INSTRUCTION MANUAL
E
A
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
Aure
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA

P. 1
Aure
P. 3 - 11
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
3mm
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts. but will not extend to the parts that are good before
gluing to defective parts during assembly.
I N D E X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 11
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
1
2
3

P. 2
Parts List
1. FUSELAGE -- 1pc.
2. MAIN WING -- 1 pair
3. ELEVATOR --1 pc.
4. RUDDER --1 pc.
5. CANOPY & COCKPIT --1 set
6. AILERON SERVO COVER --2 pcs
7. PUSHROD & PULLWIRE :--
METAL RODØ1.8x50mm (For Radio) --2 pcs
METAL ROD Ø1.8x735mm w/Threads (For Rudder) --1 pc.
8. WOODEN PARTS :--
BALSA 4x4x70mm(For Radio) --2 pcs
PLYWOOD 2x55x70mm (For Radio ) --1 pc.
WOODEN 8x16x24mm (For Aileron Servo) --4 pcs
9. PLASTIC PARTS :--
CLEVIS --3 pcs
STRAPER --3 pcs
HORN --3 sets
PLASTIC PLATE 1.5x33.5x71mm --1 pc.
10.METAL PARTS :--
LINKAGE CONNECTOR --1 set
WING JOINER Ø4x142mm --1 pc.
WING JOINER Ø6x211mm --1 pc.
STABILIZER JOINER Ø3x127mm --1 pc.
STABILIZER JOINER Ø3x144mm --1 pc.
SET SCREW 3mm --2 pcs
SCREW PM 2x12mm --4 pcs
SCREW PM 2x20mm --2 pcs
SCREW PM 3x16mm --2 pcs
SCREW PWA2x8mm --8 pcs
WASHER d3xD12mm --2 pcs
11.FUEL TUBE Ø6x5mm --6 pcs
12.DECALS --1 set

P.3
1
Aileron Servo
2
Aileron
2.5mm
1mm
1mm
PM2 x 30mm Screw
4
PWA2 x 8mm Screw
8
Wooden 8x16x24mm
Bottom View
PWA2x8mm
Straper
Fuel
Tube
PM2x12mm
Clevis
Fuel Tube
Ø6x5mm
Metal Rod
Ø1.8x50mm Horn

P.4
3
Rudder Pushrod
4
Rudder
PM2 x 20mm Screw
2
PM2 x 20mm
Clevis
Fuel Tube
Ø6x5mm
Rudder Pushrod
Ø6x5mm
2mm

P.5
5Stabilizer / Elevator
Top View
Stabilizer Joiner
Ø3x127mm
Stabilizer Joiner
Ø3x144mm

P.6
6
Servos
8
Servo Set
7
Stabilizer / Elevator
LINKAGE CONNECTOR
3 X 3mm Set Screw
1
L i n k a g e C o n n e c t o r
1
2mm Nut
1
2mm Washer
1
3mm
Bottom View
3mm
2mm
2mm
Rudder Pushrod. Included with the Radio Set.
Rudder Servo.
Please refer to attached sheet for linkage connector installation.
Balsa 4x4x70mm
Plywood 2x55x70mm
Balsa 4x4x70mm
Fuel Tube
Ø6x5mm Straper
Top View
Rudder Pushrod
Ø1.8x735mm
Elevator Servo
Rudder Servo
Linkage Connector
2mm

P.7
9Main Wing
PM3 x 16mm Screw
2
d3 x D12mm Washer
2
Bottom View Lead to Aileron Servo
Top View
PM3x16mm
d3xD12mm
3mm
Wing Joiner
Ø6x211mm
Wing Joiner
Ø6x142mm

P.8
10
Wing Setting
11
Canopy
Adjust the wing and fuselage configuration
as in the diagrams.
A = A'
B = B'
C = C'

P.9
12
C.G.
13
Control Throws
Elevator
Rudder
Aileron
40mm
40mm
53mm
53mm
15mm
15mm
75mm
2.9 in
C.G
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
The ideal C.G. position is 75mm (2.9 in.) behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
Important Safety Precautions
#First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
G1040405

ADDENDUM
LINKAGE CONNECTOR
HW7111030 & HW7111060
Drill 2mm hole at servo horn.
Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
After fastening the round nut, make sure that
the linkage connector can rotate freely.

The World Models
Manufacturing Co., LTD.
www.theworldm o d e l s .com
Warbirds
Scale
Sports
Trainer
DuctedFan Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)
G1040405