Pilot Communications Dolphin Jet User manual

Assembly Manual For
Dolphin Jet

1
INTRODUCTION
Thank you for purchasing
our Dolphin Jet. we strive to
achieve the real Quick Builded
and ARF aircraf .
It just requires the least
about of assembly of any kit
that almost finished in factory.
To obtain the perfect
performance, both the design
and manufacturing have been
taken care with the highest
quality from any hardware,
covering ,wood and glue in
the construction as well. By
optimal weight and reliable
construction, you will find this
plane is really ideal for
relaxing.
So we hope every effort and
service we offer will make you
feel easy and have a wonderful
time in the pleasure of flying.
More information on website
www.pilot-rc.com

2
WARRANTY
■All Pilot-RC products are guaranteed against
defects for 30 days of receiving your airplane. This
warranty is limited to construction or productions defects
in both material and workmanship , doesn't cover any
component parts damaged by use or modification .
■The manufacture can't supervise the assembly ,
operation and maintenance ,and can't ensure your radio
system is in good condition. Therefore ,we are not
responsible for any damage occurring during the use
of a radio controlled model. It is impossible to
determine for certain whether crash damage was the
result of a radio system failure or pilot error even
improper installation of our products. Model airplane
owner is using it on his own responsibility.
■Pilot-RC will not be liable for any costs, unless agreed
and proved beyond doubt the failure was due to faulty
materials or fabrication. Any agreed cost will not exceed
the cost of the airframe and not include engine, radio
equipment or third party claims.
■No matter what reason you wish to return this
airplane , all shipping cost will be paid by costumer.If
some parts require replacement from us ,the original
parts’ return is at costumer' expense.

3
ATTENTION
■You should not regard this plane as toy!
■To ensure safety,please read the instruction
manual thoroughly before assembly .
■Building and operating model plane require
diligent practicing and correct guidance. Any
neglect,carelessness and missing experience can
cause serious bodily harm and property damage.
■Seek the assistant of a experienced person or
airplane model clubs in assembly ,operation and
maintenance to ensure quick and successful learning
■Fly only in proven model airfield that AMA
(Academy of Model Areonautics) approved
Pilot-RC has the right to change to this plane
,instruction and limited warranty without notice.
If you have any problems and questions ,please
contact pilot –RC
Email: [email protected] , [e-mail]
Cellphone:[phone]
FAX: [phone]
Address: No.34, Chengnan Er Road , Zhongshan city, 528400, Guangdong
Province, China

4
Retract Landing Gear Installation
Landing Gear Assembly

5
Landing Gear Assembly
1, Install the servo to the nose
landing gear.
2. Install the servo arm and push
rod. Adjust to make the plane can go
straight approx. You still can adjust
by radio after install it.
4. The other items connect as the
photo shows. These items was put
under the canopy. You need to check
the tube length before you cut it.
Please note the connection from the
retract valve to the cylinder. Three
cylinder orange tubes must connect
to the orange tubes in the valve.
Three cylinder green tubes must
connect to the green tubes in the
valve.
3. Connect the air tube to the retract
gear as the photo shows. Note to use
the different color tube. Red for brake,
green and orange for the retract gear.
Check valve
Brake valve
Connect to brake
wheel
retract valve
Air Pressure Guage
Connect to the
orange tube in
retract cylinder.
Connect to the
green tube in
retract cylinder.

6
Landing Gear Assembly
6. Install the check valve, brake valve,
retract valve, fuel dot, air pressure
guage as the photo show. Install the
servo for brake and retract valve.
Fuel dot
Air pressure guage Check valve
Brake valve
Retract valve
7. Install the nose retract gear to the
fuselage.
5. Install the air throttle as the photo
shows.

7
Landing Gear Assembly
9. Put the retract gear air tube
through the hole.
8. Find the hole between the flap
servo bay and the retract gear bay.
10. This photo shows how the air
tube go through the wing.
9. Put the retract gear air tube from
the flap servo bay to the root of the
wing . There is a tunnel under the
covering as the photo shows.

8
Landing Gear Assembly
11. Screw the retract gear to the
retract gear bay in the wing. Fix the
brake air tube as photos shows.
12. Get the plastic landing gear cover.
13. Cut the covering around the
retract gear bay.
14. Apply the 30 minutes epoxy on
the bottom of the retract gear bay.

9
Landing Gear Assembly
15. Put the retract gear plastic cover
into the retract gear bay.
16. Apply the instant adhesive to glue
the plastic cover to the wing.
.