Theben theLeda S10 WH User manual

1
theLeda S10 WH 1020921
theLeda S10 BK 1020922
theLeda S20 WH 1020923
theLeda S20 BK 1020924
theLeda S10 W WH 1020931
theLeda S10 W BK 1020932
theLeda S20 W WH 1020933
theLeda S20 W BK 1020934
LED spotlight with
motion detector
EN
307286 02
1. Basic safety information 3
2. Proper use 3
Disposal 3
3. Connection 4
4. Installation 5
Installation instructions 5
5. Description 9
6. Aligning the LED spotlight 9
Setting the brightness (LUX) 10

2
Setting the time (TIME) 10
Function mode (MODE) 10
Manual operation 11
7. Walking test 12
8. Aligning the LED spotlight 13
theLeda S10 13
theLeda S20 14
9. Limiting the detection area
15
10. Technical Data 16
11. Contact 17

3
1. Basic safety information
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
!Only intended for installation out of arm‘s reach.
!High temperature! Do not touch the
metal parts of the device.
LThe LED spotlight with motion detector (PIR) conforms to
EN 60598-1 and EN 60669-2-1 if correctly installed
LIP 55 in accordance with EN 60529
LOptional with corner angle (9070969/9070987) and dis-
tance frame (9070971/9070988)
2. Proper use
•LED spotlight is used for lighting, depending on
presence and brightness
•Device is for wall mounting inside and outside
•For entrances, garages, gardens, corridors, parks, etc.
•For use in normal ambient conditions
LLamp cannot be replaced.
Replace entire spotlight if defective!
Disposal
Dispose of device in environmentally sound manner

4
3. Connection
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
Disconnect power source!
Ensure device cannot be switched on!
Check absence of voltage!
Earth and bypass
Cover or shield any adjacent live components
N L
N
L

5
4. Installation
Installation instructions
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
LObserve the recommended installation height of
1.8 m–2.5 m!
3.5 m
1 m
3 m
10 m
1 m
3 m
10 m
3.5 m
1 m
3 m
10 m
1 m
3 m
10 m
As the LED spotlight reacts to variations in temperature, avoid
the following situations:
LDo not direct the LED spotlight at objects with highly-
reective surfaces such as mirrors etc.
LDo not install the LED spotlight near heat sources, such as
heating outlets, air conditioning systems, lamps etc.

6
LDo not direct the LED spotlight at objects that move in the
wind, such as curtains, large plants etc.
LPay attention to the direction of motion during the test run
Disconnect power source
0FF
1
230V
Use spacer or corner bracket (optional)

7
2Cut out
Knock out hole here
Cut out
Knock out hole here
OR
OR
Cut out
Knock out hole here
Loosen catch mechanisms with a screwdriver and remove
LED spotlight from base
3
Make marks for the holes and drill the holes
4
Guide wire through the socket‘s seal; x socket to the wall

8
φ6mm
MOUNTING
SCREW x 2
CAUTION:
5
60mm
Fix socket to wall, connect the individual wires to the
appropriate terminal and tighten screws
Tighten the screws.
6
Place and engage the LED spotlight on the base
7
Connect LED spotlight to mains
The device need 30
seconds to warm up.
8
LThe detector needs approx. 40 s of preheating time.

9
5. Description
movable
LED spotlight
Sensor
head with 3
potentiometers
The LED spotlight has 3 potentiometers for setting time (min),
brightness (lux), and function mode.
6. Aligning the LED spotlight
LSettings via poti are taken after 15 s

10
Setting the brightness (LUX)
Turn the potentiometer towards „Moon“; the LED spotlight
only switches on when it is relatively dark.
Turn the potentiometer towards „Sun“; the LED spotlight
switches on when it is relatively bright
Turn the potentiometer to „Sun“, and the device works
independent of brightness
Setting the time (TIME)
Set the potentiometer to the desired time (2 s–30 min)
Function mode (MODE)
Turn the potentiometer to „auto“; the LED spotlight swit-
ches on when there is motion in the dark
Set Potentiometer to „10 %“ : LED spotlight switches to the
set dimming value when dark
(10 % – 50 %) for for movement to 100 %.

11
Manual operation
The lighting can be switched on manually via a circuit breaker
button.
LA circuit breaker button must be connected
LFunction only possible at night
N L
N
L
Quickly conrm Circuit breaker 2 x (within 2 s)
▻ The lighting remains switched on for 6 hours.
To switch off the lighting and return to auto mode, press
the circuit breaker briey (within 2 s)
If the circuit breaker is pressed x2 during this six second
turn-on time, the lighting is switched on again for 6 hours.

12
7. Walking test
The walking test is used to test the detection area and to
restrict it if necessary.
Set potentiometer „brightness“ to „sun“.
Set the time potentiometer (TIME) to „test“.
▻ The motion detector now always reacts to
movements (independent of brightness).
Walk through the detection area at a right angle. After the
motion detector has detected a movement, it switches on
for 2 s.
LPay attention to the direction of motion during the test.

13
8. Aligning the LED spotlight
theLeda S10
Down 60°
Down 70°
Left & Right 40° (limited by wall )
40°40°
Left: 90° (limited by corner) & Right: 45°
- with corner bracket
45°
45°
Left: 210° & Right: 45° - with spacer
45°
210°
Left: 210° & Right: 45° - with corner bracket
45°
210°

14
theLeda S20
70°
Pan Inward from 10° to 45° (limited by wall)
- with corner bracket
from 10° - 45°
Pan Outward 21° (limited by wall)
Pan Inward 45°
45°
21°
Pan Outward 40° (limited by wall)
Pan Inward 45° - with spacer
40° 45°
Pan Outward 45°, Pan Inward 45°
- with corner bracket
45°
45°

15
9. Limiting the detection area
Use enclosed stickers to adjust the motion detector to the
desired detection area.
Remove the desired part of the cover clip with scissors.
Then stick to the lens.
LENS MASK STICKER

16
10. Technical Data
Operating voltage: 230 V ± 10 %
Frequency: 50–60 Hz
Consumption with light On: 10 W / 2 x 10 W
Standby output: 0.4 W
Colour rendering index: > 80
Service life: L70/B50 / 50.000 h
Protection rating: IP 55 in accordance with EN
60529
Protection class: I in accordance with EN
60598-1
Operating temperature: –20 °C … +45 °C
Brightness setting range: 2 – 200 lx / ∞ lx
Duty cycle range: 2 s – 30 min
Detection angle: 180°
Detection area: lateral:
frontal:
max. 10 m
max. 4 m
Colour temperature / LED output
(luminous ux) / energy efciency
class:
1020931–1020934:
3000 K / 770 lm (2 x 770 lm)
/ A
1020921–1020924:
4000 K / 840 lm (2 x 840 lm)
/ A+
Mass/dimensions: 1020921+1020922: 7,64 kg/
80 x 160 x 50 mm
1020923+1020924: 7,87 kg/
167 x 160 x 50 mm
1020931+1020932: 7,64 kg/
80 x 160 x 50 mm
1020933+1020934: 7,87 kg/
167 x 160 x 50 mm

17
11. Contact
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
Addresses, telephone numbers, etc.
www.theben.de