Theben theLeda E30 WH User manual
3
1. Basic safety information
Danger of death through electric shock or
fire!
Installation should only be carried out by
a qualied electrician!
WARNING
•The LED spotlight with motion detector (PIR)
conforms to EN 60598-1 if correctly installed
•Only intended for installation outside of arm's
reach
Proper use
•LED spotlight is used for lighting, depending on
presence and brightness
•Intended for wall mounting outdoors
•Suitable for corridors, gardens, entrances, parks
etc.
•For use in normal ambient conditions
Disposal
Dispose of LED spotlight in an environmentally
sound manner (electronic waste)
4
2. Description
Sensor head with
2 potentiometers for set-
ting time (min.) and
brightness (lux)
LED spotlight
3. Connection
WARNING
Danger of death through electric shock!
Disconnect power source
Ensure device cannot be switched on
Check absence of voltage
Earth and bypass
Cover or shield any adjacent live components
8
external
conductor
switched
conductor
brown
blue
green/yellow
brown
blue
green/yellow
neutral
conductor
mains
earth
neutral
conductor
mains
earth
Tighten screws
click
Push
Place and engage the cover on the LED spotlight
Place the LED spotlight on the mounting bar and
tighten screws
Connect LED spotlight to mains
Installation instructions
As the LED spotlight reacts to variations in tempe-
rature, avoid the following situations:
•Do not direct motion detectors (PIR) of the LED
spotlight at objects with highly-reective sur-
faces, such as mirrors etc.
•Do not install the motion detector near heat
sources, such as heating outlets, air conditio-
ning systems, lamps etc.
9
•Do not direct the motion detector at objects
that move in the wind, such as curtains, large
plants etc.
•Pay attention to the direction of motion during
the test run.
1
8
0
.2
OT8.1 TEM
5ER
12 METER
3 METER
1
8
0
1 RETEM5.2OT8.
12 METER
3 METER
1
8
0
2OT8.1 RE
TEM
5.
12 METER
3 METER
10
20
30
40
40
10
20
30
40
40
10
20
30
40
40
1m
4 m
12 m
180°
3 m
•Transverse detection area: 12 m (transversal to
the detector)
•Frontal detection area: 4 m (directly approa-
ching the detector)
•Detection angle: 180 °
10
5. Walking test
The walking test is used to test the detection area
and to restrict it if necessary.
Turn the time potentiometer (min.) counterclock-
wise up to the stop.
The motion detector now only reacts to movements
(independent of brightness).
Go diagonally to the detection area. After the
motion detector has detected a movement, it
switches on for 2 s.
Pay attention to the direction of motion during
the test.
0
2
Sec
2 sec
Dusk Time
Test mode
6. Alignment
•The sensor can be rotated to left/right and
down by 90 °.
11
•The LED spotlight can be rotated up by 45 °
and down by 60 °.
90º
90º
90º
60º
45º
Limiting the detection area - using
stickers
Use the supplied stickers to adjust the motion
detector to the desired detection area.
Remove the required section of the sticker by
using scissors.
Then place on the lens.
Lens masking
12
7. Setting
The LED spotlight has 2 potentiometers for setting
the time (min.) and brightness (lux).
10min5sec
0
Min
10
05
sec
Turn On time adjustment
Environment lux level to turn On
Adjustments
Dusk/Dawn Time
Test mode
Setting the brightness (lux)
Turn the potentiometer to „Moon“; the LED spot-
light only switches on when it is relatively dark.
Turn the potentiometer to „Sun“; the LED spot-
light switches on when it is relatively bright.
Turn the potentiometer to „Sun“, and the device
works independent of brightness.
13
Setting the time (min.)
Set the potentiometer to the desired time (5 s -
10 min.).
Manual operation
The lighting can be manually switched on/off via a
circuit breaker button.
LThe surrounding brightness must be below the
set value!
LA circuit breaker button must be connected.
NL
N
L
L
Shortly press the circuit breaker button (max. 1.5
seconds).
14
▻The lighting remains switched on, until the
surrounding brightness exceeds the set value.
In order to switch off the lighting, shortly press
the circuit breaker button (max. 1.5 seconds).
Setting the twilight switch function
Turn the time potentiometer (min.) clockwise up
to the stop.
▻The twilight switch function is activated.
LNow, the motion detector does not respond to
movements anymore.
LThe connected spotlight switches on at the set
surrounding brightness
!CAUTION!
15
8. Technical data
•Operating voltage: 230 V AC +/–10 %, 50–60 Hz
•Consumption with light ON: 30 W
•Standby output: max. 0.5 W
•LED output (luminous ux):
– theLeda E30 WH: 30 W (2310 lm)
– theLeda E30 BK: 30 W (2115 lm)
•Protection rating: IP 55 in accordance with
EN 60598-1
•Protection class: I in accordance with
EN 60598-1
•Operating temperature: –20 °C … +40 °C
•Brightness setting range: 2 – 200 lx
•Duty cycle range: 5 s – 10 min.
•Detection area: transverse: max. 12 m,
frontal: max. 4 m; 180 °
•Installation height: 2.5 m
•Sensor head can be
rotated right/left, down
by: 90 °, 90 °
•Spotlight can be rotated
up by: 45 ° and down by: 60 °
•Energy efciency class: A+ (theLeda BK: A)
•Switching contact: μ-contact
•Max. switching capacity: 1000 W; 4.3 A (at cos ϕ= 1)
•Min. switching capacity: 10 mA/230 V
•Incandescent and halogen
lamp load: 1000 W
•Fluorescent lamps (LLB low-loss ballasts):
uncompensated/series
compensated: 1000 VA,
parallel compensated: 350 W
(37 µF)
16
•Fluorescent lamps (EB – electronic ballasts):
300 W
•Compact uorescent lamps (EB): 80 W
•LED lamps < 2 W: 15 W
•LED lamps > 2 – 8 W: 50 W
•LED lamps > 8 W: 50 W
9. Contact
Theben AG
Hohenbergstraße 32
72401 Haigerloch
GERMANY
Phone: +49 7474 692-0
Fax: +49 7474 692-150
Hotline
Phone: +49 7474 692-369
www.theben.de
Other manuals for theLeda E30 WH
1
This manual suits for next models
3
Table of contents
Other Theben Spotlight manuals
