Theben LUNA Series User manual

Assembly and
operating instructions
Twilight Switch
LUNA
LUNA 109
LUNA 110
109 0 100, 109 0 200
110 0 100, 110 0 200
310 317 02
GB
DGB FI
E P NL PL
LUNA 109 LUNA 110
2300 W
8mm
Lux
2000
2
Test
123
LUNA 109
2,5mm2
0,5mm -
2
220-240V~
50-60Hz
16A-10AX 250V~ –30 T
2,5mm2
0,5mm -
2
220-240V~
50-60Hz
16A-16AX
3600 W
250V~
123
8mm
I:2-35Lux
II : 35 - 200 Lux
III : 200 - 1000 Lux
IV:1-5klx
V: 5-50klx
min
min
max
LUNA 110
Lux
123
–30 T
*
*Current connection required for smooth zerocrossing switch operation
(see connection diagram) only LUNA 110).
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 1

Contents
Service address/Hotline 2
Basic advice 3
Connection/assembly 4
Connection/assembly of a light sensor 5
Display and control elements 6
Initial start-up 7
Technical data 8
2
Serviceadresse
Theben AG
Hohenbergstr. 32
72401 Haigerloch
DEUTSCHLAND
Fon +49 (0) 74 74/6 92-0
Fax [phone]
Hotline
Fon +49 (0) 74 74/6 92-369
Fax [phone]
[email protected]
Adresses, telefon numbers etc.
www.theben.de
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 2

3
Basic advice
• The device corresponds to EN 60669-2-1; it is designed for installation on DIN top hat rails
(in accordance with EN 50022)
Designated use
• The twilight switch is used for controlling the light facilities of streets, external stairways
shop windows, entrances etc.
• For use only in closed, dry rooms (device); the sensor is intended for ourdoor installation
Disposal
Dispose of equipment in an environmentally-friendly manner
Danger of death through electric shock or fire!
Assembly may only be carried out by qualified electricians!
WARNUNG
GB
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 3

4
Connection/assembly
Connect cable
Strip cable back to 8 mm (max. 9).
Insert cable in open terminal at 45° angle
(2 cables per terminal position possible).
To open spring screwless terminal, press upwards
with screwdriver.
Danger of death through electric shock!
Assembly may only be carried out by qualified electricians!
Disconnect power supply!
Ensure it is not turned on again!
Check power is off!
Earth and short-out!
Cover or shield any adjacent live parts.
Cable 45°
Spring
screwless
terminal
opener
Test tap
Spring screwless
terminal
WARNUNG
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 4

5
Connection/Assembly of a light sensor
ca. 38 mm
O15,2 mm
0,75 mm2< 50 m
1,5 mm < 100 m
2
max. 8 mm
Note the length of the connecting cable:
max. 100 m (2 x 1,5 mm2), max. 50 m (2 x 0,75 mm2)
Avoid running the sensor line parallel to conductors.
Surface-mounted light sensor: 0,5–2,5 mm2, strip the wire
to 10 mm (max. 11 mm).
907 0 011 907 0 416 Surface-mounted light sensor Built-in light sensor
GB
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 5

6
Display and control elements
I:2-35Lux
II : 35 - 200 Lux
III : 200 - 1000 Lux
IV:1-5klx
V: 5-50klx
min
min
max
LUNA 110
Lux
123
LUNA 109
LUNA 110




Lux
2000
2
Test
123
LUNA 109



Potentiometer for setting the brightness: 2-2000 lx
Key Test for checking the installation (independent of
brightness)
Immediate display of the switched condition by means
of a red LED
Display of channel condition by means of a green LED
(relay)
Potentiometer for setting the brightness treshold
Potentiometer for setting the brightness range:
and PERM ON/PERM OFF (test)
– I: 2–35 lx
– II: 35–200 lx
– III: 200–1.000 lx
– IV: 1.000–5.000 lx
– V: 5.000–50.000 lx
+as described above
Potentiometer for switch ON/switch Off delay
(0 to 20 min.)
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 6

I:2-35Lux
II : 35 - 200 Lux
III : 200 - 1000 Lux
IV:1-5klx
V: 5-50klx
min
min
max
LUNA 110
Lux
123
7
Initial start-up
The twilight switch with external light sensor is used
for controlling the light facilities of streets, stairways, ent-
rances etc.
Set the desired range I-V on the potentiometer 
using a screw driver.
Set the desired treshold .
The red LED will light up, if the set Lux value underruns
the ambient brightness.
Recommendation: set a delay of at least 1 min,
to avoid switching errors owing to lightening flashes,
car headlights etc.
LUNA 110




Typical brightness values
daylight (bright) 80.000 lx
office rooms 500 lx
corridors and stairs 100-150 lx
street lighting 15 lx
full moon ca. 0,3 lx
GB
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 7

Technical Data LUNA 109 LUNA 110
Nominal voltage: 220–240 V, ~, +10 %/–15 % 220–240 V, ~, +10 %/–15 %
Frequency: 50–60 Hz 50–60 Hz
On/off switch delay: 1 min. 0–20 min.
Power consumption: ca. 3 VA ca. 3 VA
Contact material: AgSnO2AgSnO2
Contact: floating phase-independent
(zero-crossover switching)
Gap: <3 mm (μ) <3 mm (μ)
Switching capacity max.: 16 A, 250 V~, cos ϕ= 1 16 A, 250 V~, cos ϕ= 1
Switching capacity min.: 10 mA/230 V AC 10 mA/230 V AC
100 mA/12 V AC/DC 100 mA/12 V AC/DC
Switching capacity fluorescent lamps: 10 AX 16 AX
Incandescent lamp load: 2300 W 3600 W
Halogen lamp load: 2300 W 3600 W
Fluorescent lamp loads – capacitive ballast
uncorrected: 2300 VA 3600 VA
series corrected: 2300 VA 3600 VA
parallel corrected: 400 VA (42μF) 1200 VA (130μF)
dual circuit: 2300 VA 3600 VA
Fluorescent lamps – electronic ballast: 300 VA 1200 VA
Mercury and sodium vapour
lamps: series corrected: 400 VA (42μF) 1200 VA (130μF)
Compact fluorescent
lamps – electronic ballast: 9x 7W, 7x11 W, 34x7 W, 27x11 W, 24x15 W,
7x15 W, 7x20 W, 7x23 W 22x23 W
Permissible ambient temperature: –30 °C ... +55 °C (device) –30 °C ... +55 °C (device)
–40 °C ... +70 °C (sensor) –40 °C ... +70 °C (sensor)
Protection class: II (light sensors III) for designated installation
Protection rating: IP 20, IP 55 (surface-mounted light sensor), IP 65 (built-in light sensor) in accordance
with EN 60529
8
LUNA 109_LUNA 110_310 317_GB 28.07.2008 8:11 Uhr Seite 8