Planet FNSW-1600P User manual

16-Port 10/100Mbps PoE Fast Ethernet Switch
FNSW-1600P
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2011.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from
the power circuit.
Without removing power cable, the device will still consuming power from the
power source. In the view of Saving the Energy and reduce the unnecessary power
consuming, it is strongly suggested to remove the power connection for the device
if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such WEEE
separately.
Revision
PLANET 16-Port 10/100Mbps PoE Fast Ethernet Switch User's Manual
For Model: FNSW-1600P
Revision: 1.1 (November, 2011)
Part No.: 2351-A50170-001

Table of Contents
1. Introduction................................................................................................ 5
1.1 Checklist .............................................................................................. 5
1.2 Product Description................................................................................ 5
1.3 Features............................................................................................... 6
1.4 Specication ......................................................................................... 7
2. Hardware Description .................................................................................. 8
2.1 Front Panel........................................................................................... 8
2.1.1 LED Indicators .............................................................................. 8
2.2 Rear Panel............................................................................................ 9
3. Hardware Installation..................................................................................10
3.1 Desktop Installation .............................................................................10
3.2 Rack Mounting.....................................................................................11
3.3 Product Application...............................................................................12
3.4 Power over Ethernet Powered Device ....................................................13
4. Power over Ethernet Overview.....................................................................14
5. Troubleshooting..........................................................................................17
Appendix A Networking Connection ..................................................................18
A.1 DATA OUT PoE Switch RJ-45 Port Pin Assignments..................................18
A.2 10/100Mbps, 10/100Base-TX ................................................................18

5
1. Introduction
1.1 Checklist
Check the contents of your package for following parts:
FNSW-1600P x 1l
User's Manual x 1l
Power Cord x 1l
Rubber Feet x 4l
Two Rack-mounting Brackets with Attachment Screws x 8l
If any of these pieces are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing material,
and use them against to repack the product in case there is a need to return it to
us for repair.
In the following section, the term “PoE Fast Ethernet Switch” means the Switch
device, ie. FNSW-1600P; term of “switch” can be any third switches.
1.2 Product Description
Centralized Power Distribution for Ethernet Networking
To fulll the demand of sufcient PoE power for network applications with Gigabit
speed transmission, PLANET introduces a new member in the 802.3af PoE Fast
Ethernet Switch family – FNSW-1600P, the 16-Port 10/100Mbps 802.3af
Power over Ethernet Switch with 125 Watts PoE budget. The 16 x 802.3af
PoE ports provide PoE power injector function which is able to drive at least 9 x
IEEE 802.3af 12.95 Watts Class 3 compliant powered devices. The FNSW-1600P
also provides a simple, cost-effective, and non-blocking wire-speed performance
with 19-inch metal shape for deployment in compact housing, SOHO ofce or
department network application.
Great Ethernet Trafc Transmission Ability
The FNSW-1600P features high performance switch architecture capable of
providing the non-blocking 3.2Gbps switch fabric and wire-speed throughput as
high as 2.38Mpps, which greatly simplies the tasks of upgrading the LAN for
catering to increasing bandwidth demands. Besides, the 802.3x Full-Duplex ow
control function of the FNSW-1600P enables PD devices and servers directly
connect to the Switch for wire-speed packet transfer performance without risk of
packet loss.

6
Easy Cable Connection
With data and power over Ethernet from one unit, the FNSW-1600P shall reduce
cables and eliminates the need for dedicated electrical outlets on the wall, ceiling or
any unreachable place. A wire carries both data and power lowering the installation
costs, simplifying the installation effort and eliminating the need for electricians or
extension cords. With 125Watts Power Budget, the FNSW-1600P is ideal for small
business and workgroups requiring to deploy the PoE for the wireless access points,
IP-based surveillance camera or IP phones in any places easily, efciently and cost
effective.
1.3 Features
RJ-45 Interfacel
16-Port 10/100Mbps Fast Ethernet ports
Each Ethernet port supports 48V DC power to PoE Powered Device
Power over Ethernetl
Comply with IEEE 802.3af Power over Ethernet Mid-Span PSE
Up to 16 IEEE 802.3af devices powered
PoE Power Budget 125 Watts
Supports PoE Power up to 15.4 Watts for each PoE port
Auto detect powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
Switchingl
Hardware based 10/100Mbps Auto-Negotiation and Auto MDI/MDI-X
Flow control for Full Duplex operation and back pressure for Half Duplex oper-
ation
Integrates address look-up engine, supporting 8K absolute MAC addresses
Automatic address learning and address aging
Hardwarel
19-inch size, 1U height
LED indicators for PoE ready and PoE activity
2 silent FAN to provide stable and efcient power performance

7
1.4 Specication
Model FNSW-1600P
16-Port 10/100Mbps PoE Fast Ethernet Switch
Hardware Specication
Network Connector 16-Port RJ-45 for 10/100Base-TX
PoE Inject Port 16-Port with 802.3af PoE injector function
LED Display
System: Power (Green)
Per port: PoE (Orange)
LNK/ACT (Green)
Switch Architecture Store and Forward switch architecture
MAC Address 8K MAC address table with Auto learning function
Switch Fabric 3.2Gbps
Switch Throughput 2.38Mpps@64Bytes
Power Requirement AC 100~240V, 50/60Hz, 2A max.
Power Consumption Max.135 Watts / 460 BTU
Dimension (W x D x H) 445 x 207 x 45 mm (1U height)
Weight 2.33kg
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type Mid-Span
PoE Power Output Per Port 48V DC, 350mA. Max. 15.4 Watts
Power Pin Assignment 4/5(-), 7/8(+)
PoE Power Budget 125 Watts
Standard Conformance
EMI Safety FCC Class A, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Environment
Operating environment 0 ~ 50 Degree C
Storage environment -40 ~ 70 Degree C
Operating Humidity 5 ~ 95%, relative humidity, non-condensing
Storage Humidity 5 ~ 95%, relative humidity, non-condensing

8
2. Hardware Description
This product provides two different running speeds – 10Mbps and 100Mbps in the
same switch and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of FNSW-1600P. For easier
management and control of the Switch, familiarize yourself with its display
indicators, and ports. Front panel illustrations in this chapter display the unit LED
indicators. Before connecting any network device to the FNSW-1600P, please read
this chapter carefully.
2.1 Front Panel
The Front Panel of the FNSW-1600P PoE Fast Ethernet Switch consists of 16 x
Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports. The LED Indicators are also
located on the front panel of the FNSW-1600P.
Figure 2-1: FNSW-1600P Switch Front Panel
2.1.1 LED Indicators
System
LED Color Function
PWR Green Light: Indicate the Switch has power.
Per 10/100Mbps Port
LED Color Function
PoE In Use Orange Light: Indicate the port is providing 48V DC in-line
power.
LNK/ACT Green
Light: Indicate the link through that port is
successfully established.
Blink: Indicate that the Switch is actively sending or
receiving data over that port.

9
2.2 Rear Panel
The rear panel of the FNSW-1600P PoE Fast Ethernet Switch indicates an AC inlet
power socket, which accepts input power from 100 to 240V AC, 50-60Hz, 2A.
Figure 2-2: FNSW-1600P Switch Rear Panel
Power
Notice
The device is a power-required device, it means, it will not work till
it is powered. If your networks should active all the time, please
consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime.
In some area, installing a surge suppression device may also help
to protect your FNSW-1600P from being damaged by unregulated
surge or current to the FNSW-1600P or the power adapter.

10
3. Hardware Installation
Start up
Please refer to the followings for your cabling:
10/100Base-TX
All 10/100Base-TX ports come with Auto-Negotiation capability. They automatically
support 100Base-TX and 10Base-T networks. Users only need to plug a working
network device into one of the 10/100Base-TX ports, and then turn on the FNSW-
1600P. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps
after the negotiation with the connected device.
Cabling
Each 10/100Base-TX ports use RJ-45 sockets -- similar to phone jacks -- for
connection of unshielded twisted-pair cable (UTP). The IEEE 802.3 / 802.3u Fast
Ethernet standard requires Category 5, 5e UTP for 100Mbps 100Base-TX. 10Base-T
networks can use Cat. 3, 4, 5 (see table below). Maximum distance is 100meters
(328 feet).
Port Type Cable Type Connector
10Base-T Cat. 3, 4, 5, 2-pair RJ-45
100Base-TX Cat. 5, 5e UTP, 2-pair RJ-45
Any Ethernet devices like hubs / PCs can connect to the FNSW-1600P by using
straight-through wires. The 16-10/100Mbps ports are auto-MDI/MDI-X can be used
on straight-through or crossover cable.
3.1 Desktop Installation
To install the PoE Fast Ethernet Switch on desktop, simply follow the next steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the PoE
Fast Ethernet Switch, as shown in Figure 3-1.
Figure 3-1: Attaching the Rubber Feet to the PoE Fast Ethernet Switch
Step 2: Place the PoE Fast Ethernet Switch on desktop near an AC power source.
Step 3: Keep enough ventilation space between the PoE Fast Ethernet Switch and
the surrounding objects.