Thermalright Macho 120 Rev.A User manual

Thermalright
Macho 120 Rev.A

× 1
4
4
8
× 1 × 2
× 1
× 4
× 4
× 4
× 7
× 5
Chill Factor 2g
× 4
× 4
× 1× 1
× 1
Macho 120 Rev.A
Assembly Package

Macho 120 Rev.A
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Heatsink Body 120mm Fan
Clip
120mm Fan
Screw Nut
Mylar Film
Anti-Vibration Pads
Mounting Plate
M3 L6 Screw
Anchoring Mount
Metal Back Plate
Backplate cap
Intel Washer
(small)
M3 L10 Screw
Intel 775/1150/1151/1155/1156/1366

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3 4
4
5
5
6
6
87
7 8
10
9
10
13
16
11
14
17
1514
12
15
1716
9
12 1311
Heatsink Body ×1
Screw Nut ×4
Anti-Vibration Pad ×4
Mylar Film ×1
120mm Fan ×1
120mm Fan Clip ×2
Thermal paste ×1
Intel Washer (small) ×4
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
AMD Washer (big) ×4
Anchoring Mount ×1
Mounting Plate ×1
M3 L6 Screw ×7
Chill Factor 2g
M3 L10 Screw ×5
Backplate Cap ×1
Screw driver ×1

3
Installation Instructions:
Step 1:
Step 2:
Step 4:Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
Step 2 : Backplate Installation
Choose the platform (775/1150/1151/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars
go through the Metal Back Plate and the Mylar lm from bottom towards top. And then place the Metal
Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars.
Step 3 : 775 Back Plate Cap
Note: When installing on a 775 platform, please
rst insert the Back Plate Cap into the opening on
the Back plate, make sure you have the Cap facing
downwards. (Only for LGA775 platform, all other
platforms go directly to Step 3.).
Step 4 : Screw Cylinder Installation
Take one M3L10 screw and put one washer for
Intel around the screw pillar. Snap it through
one of holes around CPU socket from bottom
towards top. Cap the screw pillar with the screw
nut included and then tighten up. Now repeat this
installation for the other three screw pillars in a
criss-cross pattern.
1366
775
1150
1151
1155
1156
12
4
3

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 5: Step 6:
Step 7:
Step 6 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to x the Anchoring
Mount on to the Screw Nuts.
Step 7: Mounting Plate Installation
Place the Heatsink Body on top of the CPU.
Make the Mounting Plate go through the Heatsink
Body. Then use the supplied Screw Driver
to fasten the two M3L6 Screws to Secure the
Mounting Plate.
Step 8: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the M3L6
Screw underneath the cooler.
Step 9: Step 10:
Step 9 : Fan Installation
Place the included 120mm fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 10 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 8:
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
12
4
3

Macho 120 Rev.A
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
120mm Fan Clip
120mm Fan
Mounting Plate
M3 L6 Screw
Anchoring Mount
LGA2011 Type B
Screw Pillars
Anti-Vibration Pads
Heatsink Body
Intel 2011/2011-3/2066

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3 4
4
5
5
6
6
87
7 8
10
9
10
13
16
11
14
17
1514
12
15
1716
9
12 1311
Heatsink Body ×1
Screw Nut ×4
Anti-Vibration Pad ×4
Mylar Film ×1
120mm Fan ×1
120mm Fan Clip ×2
Thermal paste ×1
Intel Washer (small) ×4
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
AMD Washer (big) ×4
Anchoring Mount ×1
Mounting Plate ×1
M3 L6 Screw ×7
Chill Factor 2g
M3 L10 Screw ×5
Backplate Cap ×1
Screw driver ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
Step 2 : Install the four screw pillars.
Take one M3L10 screw and put one washer for Intel around the screw pillar. Snap it through one of
holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and
then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern.
Step 3 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 screws to x the Anchoring Mount on
to the Screw Nuts.
12
3
4
12
3
4

Macho 120 Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5:
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
Step 5: Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make
the Mounting Plate go through the Heatsink Body.
Then use the supplied Screw Driver to fasten the
two M3L6 Screws to Secure the Mounting Plate.
Chill Factor
2g
Chill Factor
2g
Step 6:
Step 7: Step 8:
Step 7 : Fan Installation
Place the included 120mm Fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 8 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.
Chill Factor
2g
Chill Factor
2g

Macho 120 Rev.A
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
AM2/AM2+/AM3/AM3+/AM4/FM1/FM2/FM2+
Heatsink Body 120mm Fan
Clip
120mm Fan
Screw Nut
Mylar Film
Anti-Vibration Pads
Mounting Plate
M3 L6 Screw
Anchoring Mount
Metal Back Plate
Backplate cap
AMD Washer
(big)
M3 L10 Screw

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3 4
4
5
5
6
6
87
7 8
10
9
10
13
16
11
14
17
1514
12
15
1716
9
12 1311
Heatsink Body ×1
Screw Nut ×4
Anti-Vibration Pad ×4
Mylar Film ×1
120mm Fan ×1
120mm Fan Clip ×2
Thermal paste ×1
Intel Washer (small) ×4
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
AMD Washer (big) ×4
Anchoring Mount ×1
Mounting Plate ×1
M3 L6 Screw ×7
Chill Factor 2g
M3 L10 Screw ×5
Backplate Cap ×1
Screw driver ×1

11
Installation Instructions:
Step 1:
Step 2:
Step 4:Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
Step 3 : Back Plate Cap
Note: When installing on an AMD platform, please
rst insert the Back Plate Cap into the opening on
the Metal Back plate, make sure you have the Cap
facing downwards.
Step 4 : Screw Cylinder Installation
Take one M3L10 screw and put one washer for
AMD around the screw pillar. Snap it through
one of holes around CPU socket from bottom
towards top. Cap the screw pillar with the screw
nut included and then tighten up. Now repeat this
installation for the other three screw pillars in a
criss-cross pattern.
Step 2 : Backplate Installation
Choose the platform AMD AM3/AM4 you are in use. Make four M3L10 Screw Pillars go through the
Metal Back Plate and the Mylar lm from bottom towards top. And then place the Metal Back Plate on the
table. Put the four Washers (for AMD) around the Screw Pillars.
AM4
AM3
12
3
4

The Ultimate Cooling Solutions!
www.thermalright.com
12
Chill Factor
2g
Chill Factor
2g
Step 5: Step 6:
Step 7:
Step 6 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to x the Anchoring
Mount on to the Screw Nuts.
Step 7: Mounting Plate Installation
Place the Heatsink Body on top of the CPU.
Make the Mounting Plate go through the Heatsink
Body. Then use the supplied Screw Driver
to fasten the two M3L6 Screws to Secure the
Mounting Plate.
Step 8: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the M3L6
Screw underneath the cooler.
Step 9: Step 10:
Step 9 : Fan Installation
Place the included 120mm fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 10 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 8:
Chill Factor
2g
Chill Factor
2g
12
3
4

Macho 120 Rev.A
13
Macho Kühlkörper 120 mm
Lüfterklammer
120 mm Lüfter
Rändelschraube
Leitschutzfolie
Anti-Vibrationpad
Befestigungsplatte
M3 L6 Schraube
Montagerahmen
Multi Platform Backplate
Backplate Einsatz
Intel Unterlegscheibe
(klein)
M3 L10 Schraube
Explosionszeichnung
Wichtig! Bitte prüfen Sie vor der Montage ob für Ihren Kühler aktualisierte
Montagehinweise auf der Webseite www.thermalright.com verfügbar sind.
Intel 775/1150/1151/1155/1156/1366

The Ultimate Cooling Solutions!
www.thermalright.com
14
1
1
2
2
3
3 4
4
5
5
6
6
87
7 8
10
9
10
13
16
11
14
17
1514
12
15
1716
9
12 1311
Macho Kühlkörper ×1
Rändelschraube ×4
Anti-Vibrationspad ×4
Leitschutzfolie
×1
120 mm Lüfter ×1
120 mm
Lüfterklammer ×2
Wärmeleitpaste ×1
Intel Unterlegescheibe
(klein) ×4
Multi Platform
Backplate
×1
LGA2011 Type B
Adapterschraube x4
AMD Unterlegscheibe
(groß) ×4
Montagerahmen ×1
Befestigungsplatte ×1
M3 L6 Schraube ×7
Chill Factor 2g
M3 L10 Schraube ×5
Backplate Einsatz ×1
Schraubendreher ×1
Komponenten

15
Installationsanleitung:
Schritt 1:
Schritt 2:
Schritt 4:Schritt 3:
Nachdem Sie den Macho Kühler aus der Verpackung genommen haben demontieren Sie zunächst den
120 mm Lüfter, um die Installation zu vereinfachen. Belassen Sie hierbei die Lüfterklammern am
Kühlkörper - entfernen Sie diese nicht. Bringen Sie die vier selbstklebenden Anti-Vibrationspads an den
Ecken des Kühlkörpers an.
Achten Sie auf die entsprechenden Intel Sockel (775/1150/1151/1155/1156/1366) vorgesehene
Bohrungen in der Multi Plattform Backplate. Führen Sie die M3L10 Schrauben jeweils
von unten durch die Backplate und die mitgelieferte Leitschutzfolie und legen dann die Backplate
auf den Tisch. Legen Sie die vier Unterlegscheiben (für Intel) über die hervorstehenden Gewinde.
Beachten Sie:
Bei Verwendung einer Intel Socket 775 Plattform
setzen Sie zuerst den Backplateeinsatz in die
quadratische Öffnung der Backplate ein. Gehen
Sie sicher das der Aufsatz nach unten zeigt.
(Nur für LGA775 Plattformen)
Legen Sie die vier Unterlegscheiben (für Intel)
über jede einzelne der vier M3L10 Schrauben.
Führen Sie diese anschließend von unten durch
die Montagelöcher des Mainboards, die sich um
den CPU Sockel herum benden. Nun drehen
Sie die Rändelschrauben von oben auf die
hervorstehenden Gewinde und ziehen diese
in kreuzweiser Reihenfolge (siehe Abbildung)
vorsichtig an.
1366
775
1150
1151
1155
1156
12
4
3

The Ultimate Cooling Solutions!
www.thermalright.com
16
Schritt 5: Schritt 6:
Schritt 7:
Tragen Sie eine hauchdünne Schicht
Wärmeleitpaste auf der Oberäche der CPU und
auf der Unterseite des Kühlers auf.
Setzen Sie den Montagerahmen auf die
Rändelschrauben. Verwenden Sie die vier
M3L6 Schrauben, um den Montagerahmen
auf den Rändelschrauben zu befestigen.
Platzieren Sie nun den Kühlkörper auf die CPU.
Führen Sie anschließend die Befestigungsplatte
durch den Kühlkörper und benutzen die beiden
M3L6 Schrauben, um die Befestigungsplatte zu
befestigen.
Führen Sie den mitgelieferten
Schraubendreher durch das
Loch in der Mitte des
Kühlkörpers, um leichter
Zugang zu den M3L6
Schrauben unterhalb des
Kühlers zu erhalten.
Schritt 9: Schritt 10:
Positionieren Sie den mitgelieferten 120 mm Lüfter
auf die Kühlerseite mit den bereits angebrachten
AntiVibrationspads. Nun sichern Sie den Lüfter
mit den 120 mm Lüfterklammern, indem Sie
diese über den Lüfterrahmen klappen und die
spitzwinkeligen Ecken in den Montagelöchern des
Lüfters einrasten lassen.
Verbinden Sie den Lüfterstecker mit dem
CPU PWM Lüfteranschluss auf dem Mainboard.
Die Installation ist nun abgeschlossen.
Bitte prüfen Sie die ordnungsgemäße Funktion
vor Inbetriebnahme Ihres PC.
Schritt 8:
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
12
4
3

Macho 120 Rev.A
17
Explosionszeichnung
Wichtig! Bitte prüfen Sie vor der Montage ob für Ihren Kühler aktualisierte
Montagehinweise auf der Webseite www.thermalright.com verfügbar sind.
Macho Kühlkörper 120 mm
Lüfterklammer
120 mm Lüfter
LGA2011 Type B
Adapterschraube
Anti-Vibrationpad
Befestigungsplatte
M3 L6 Schraube
Montagerahmen
Intel 2011/2011-3/2066