Thermalright Silver Arrow IB-E Extreme User manual

Thermalright
Silver Arrow IB-E Extreme
Ver 1.1

× 4
× 7
× 1
× 1
× 1
4
4
8
× 4
× 5
× 1
× 1
× 1
× 8
× 1
× 6
× 4
× 4
Silver Arrow IB-E Extreme
Assembly Package
× 1

Silver Arrow IB-E Extreme
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 775/1150/1151/1155/1156/1366
Heatsink Body
Fan Clip
Screw Nut
Mounting Plate
Intel Washer(small)
Back Plate Cap
Anti Vibration
Pads
Metal Back Plate
Mylar
M3 L10 Screw
Anchoring Mount
M3 L6 Screw
TY143 Fan
TY143 Fan

2
The Ultimate Cooling Solutions!
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17 18
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×7
Backplate Cap ×1
Chill Factor III ×1
Wrench ×1
TY-143 Fan ×2 Mylar x1
Mounting Plate ×1
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17 18161514

3
Installation Instructions:
Step 1:
Step 2:
Step 4:
Step 3:
Step 5:
Step 1 : Back Plate Installation
Choose the platform (LGA 775/1150/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars go
through the Metal Back Plate+Mylar and the Mylar lm from bottom towardstop.And then place the Metal
Back Plate+Mylar on the table. Put the four Washers (for Intel) around the Screw Pillars.
Step 2 : 775 Back Plate Cap
Note: When installing on a LGA775 platform,
please first insert the Back Plate Cap into the
opening on the Back plate. Make sure you have
the Cap facing downwards. (Only for LGA775,
not applicable to LGA 1150/1155/1156/1366).
Step 4 : Anchoring Mount Installation
Anchoring Mount InstallationPlace the Anchoring
Mount on the Screw Nuts. Use the four M3L6
Screws to xthe Anchoring Mount on to the Screw
Nuts
on a criss cross pattern.
Step 3 : Screw Cylinder Installation
Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four
holes around the processor socket. Cap the four
Screw Cylinders with the four Screw Nuts on a
criss cross pattern. Make sure the side with a
washer is facing the Back Plate.
Step 5 : Applying Thermal Paste
Apply the Chill Factor III to the base of the
Heatsink and the surface of the CPU evenly.
4
2
3
1
142
3
1366
775
1150
1151
1155
1156

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 6:
Step 7:
Step 8:
Step 8 : Installation Completed
Connect the two TY-143 Fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.
Step 7 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
Step 6 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the Mounting Plate. Take turns a few times and slowly
down.
To PSU 4 Pin Molex
Connector

Silver Arrow IB-E Extreme
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Heatsink
Body
Fan Clip
LGA2011 Type B Screw Pillars
Mounting Plate
Anchoring Mount
M3 L6 Screw
TY143 Fan
Anti Vibration
Pads
TY143 Fan
Intel 2011/2011-3/2066

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17 18
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×7
Backplate Cap ×1
Chill Factor III ×1
Wrench ×1
TY-143 Fan ×2 Mylar x1
Mounting Plate ×1 LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17 18161514
Metal Back Plate ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Screw Pillar Installation
Screw on the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame
around the processor socket Take turns on a criss-cross pattern.
Step 2 : Anchoring Mount Installation
Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4
M3L6 Screws on a criss-cross pattern.
Step 3 : Applying Thermal Paste
Apply the Chill Factor III to the base of the Heatsink and the surface of the CPU evenly.
4
4
1
1
3
3
2
2

The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5:
Step 6:
Step 5 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
Step 4 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the Mounting Plate Take turns a few times and slowly
down.
Step 8 : Installation Completed
Connect the two TY-143 Fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.
To PSU 4 Pin Molex
Connector

Silver Arrow IB-E Extreme
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
AM2/AM2+AM3/AM3+/AM4/FM1/FM2/FM2+
Heatsink
Body
Fan Clip
Screw Nut Mounting Plate
AMD Washer (big)
Back Plate Cap
Metal Back Plate
Mylar
M3 L10 Screw
Anchoring Mount
M3 L6 Screw
TY143 Fan
Anti Vibration
Pads
TY143 Fan

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17 18
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×7
Backplate Cap ×1
Chill Factor III ×1
Wrench ×1
TY-143 Fan ×2 Mylar x1
Mounting Plate ×1 LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17 18161514
Metal Back Plate ×1

11
Installation Instructions:
Step 1:
Step 2:
Step 4:
Step 3:
Step 1 : Back Plate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screws go through the Metal Back
Plate+Mylar from bottom towards top. And then place the Metal Back Plate+Mylar on the table. Put the
four Washers (for AMD) around the Screw Cylinders.
Step 2 : 939 Back Plate Cap
Note: When installing on a 939 platform, please
first insert the Back Plate Cap into the opening
on the Back plate. Make sure you have the Cap
facing downwards. (Only for 939).
Step 3 : Screw Cylinder Installation
Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four
holes around the processor socket. Cap the four
Screw Cylinders with the four Screw Nuts on a
criss cross pattern. Make sure the side with a
washer is facing the Back Plate.
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to fix the Anchoring
Mount on to the Screw Nuts on a criss cross
pattern.
Step 5 : Applying Thermal Paste
Apply the Chill Factor III to the base of the
Heatsink and the surface of the CPU evenly.
Step 5:
4
4
1
1
3
3
2
2
AM4
AM3

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 6:
Step 7:
Step 8:
Step 6 : Mounting Plate Installation
Place the Heat Sink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate. Take turns a few times and slowly down.
Step 7 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
Step 8 : Installation Completed
Connect the two TY-143 Fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.
To PSU 4 Pin Molex
Connector

Silver Arrow IB-E Extreme
13
Explosionszeichnung
Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte
Montage-hinweise auf der Webseite www.thermalright.com verfügbar sind.
Silver Arrow IB-E
Kühlkörper
Lüfterklammer
Rändelschraube
Befestigungsplatte
Intel Unterlegscheibe
(klein)
Backplateeinsatz
Anti Vibrations
pad
M3 L10 Schraube
Montagerahmen
M3 L6 Schraube
TY143 Lüfter
TY143 Lüfter
Metallbackplate
Leitschutzfolie
Intel 775/1150/1151/1155/1156/1366

14
The Ultimate Cooling Solutions!
Komponenten
1 2 3
4 6
7 8 9
10
13
16
11
14
17
15
12
Silver Arrow IB-E
Kühlkörper ×1
M3 L6 Schraube ×7
Backplateeinsatz ×1 gekröpfter
Montageschlüssel ×1
Wärmeleitpaste ×1
PWM Y-Kabel ×1
TY-143 Lüfter ×2
Befestigungsplatte ×1
Metallbackplate ×1
LGA2011 Type B
Adapterschraube x4
M3 L10 Schraube ×5
AMD Unterlegscheibe
(groß)
×4 Anti Vibrationspad ×8
Montagerahmen ×1
5
Rändelschraube ×4
Intel Unterlegscheibe
(klein) ×4
Lüfterklammer x6
1 2 3
4 5 76 8
911 131210
18
Leitschutzfolie x1
17 18161514

15
Installationsanleitung:
Schritt 1:
Schritt 2:
Schritt 4:
Schritt 3:
Schritt 5:
Achten Sie auf die für die entsprechenden Intel Sockel (LGA 775/1150/1155/1156/1366)
vorgeseheneBohrungen in der Multi Plattform Backplate. Führen Sie die vier M3L10 Schrauben jeweils
vonuntendurch die Backplate und die mitgelieferte Leitschutzfolie und legen dann die Backplate auf
denTisch.Legen Sie die vier Unterlegscheiben (für Intel) über die hervorstehenden Gewinde.
Beachten Sie: Bei Verwendung einer Intel Sockel
LGA775 Plattform setzen Sie zuerst den
Backplate Aufsatz in die quadratische Öffnung
der Backplate ein. Gehen Sie sicher, dass der
Aufsatz nach unten zeigt.
Set zen Si e den Mont agerahmen auf di e
Rändelschrauben. Verwenden die vier M3L6
Schrauben, um den Montagerahmen auf den
Rändelschrauben zu befestigen.
Platzieren Sie das Mainboard von oben auf die
Backplate, so dass die hervorstehenden
Schraubengewinde durch die Löcher um den
Prozessorsockel gehen. Schrauben Sie die
Rändelsch rauben auf die vier Schraubengewinde.
Achten Sie dabei darauf, dass die Seite mit der
Unterlegscheibe zur Backplate zeigt.
Tragen Sie eine hauchdünne Schicht
Wärmeleitpaste auf der Oberäche der CPU und
auf der Unterseite des Kühlers auf.
LGA2011 Type B
Adapterschraube x4
4
2
3
1
142
3
1366
775
1150
1151
1155
1156

The Ultimate Cooling Solutions!
www.thermalright.com
16
Schritt 6:
Schritt 7:
Schritt 8:
Führen Sie zuerst das untere Ende der Lüfterklammer durch das untere Befestigungsloch des TY-143
Lüfters. Haken Sie nun die Lüfterklammer in den Lüfterklammernschlitz des Kühlkörpers ein. FührenSie
jetzt das obere Ende der Lüfterklammer durch das obere Befestigungsloch des TY-143 Lüfters.
Wiederholen Sie den Vorgang bei den Lüfterklammern auf dem TY-143 Lüfter.
Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte durch
den Kühlkörper und benutzen die beiden M3L6 Schrauben, um die Befestigungsplatte zu befestigen.
Schließen Sie den Lüfterstecker an den CPU PWM Lüfteranschluss auf dem Mainboard an.
Bitte prüfen Sie die ordnungsgemäße Funktion vor der Inbetriebnahme Ihres PC. Die Installation ist
abgeschlossen.
To PSU 4 Pin Molex
Connector

Silver Arrow IB-E Extreme
17
Explosionszeichnung
Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte
Montage-hinweise auf der Webseite www.thermalright.com verfügbar sind.
Lüfterklammer
LGA2011 Type B Adapterschraube
Befestigungsplatte
Montagerahmen
M3 L6 Schraube
TY143 Lüfter
Silver Arrow IB-E
Kühlkörper
Anti Vibrationspad
TY143 Lüfter
Intel 2011/2011-3/2066