Thermalright Silver Arrow SB-E Extreme User manual

Thermalright
Silver Arrow SB-E
Extreme

× 4
× 6
× 1
× 1
× 1
4
4
8
× 4
× 4
× 1
× 1
× 1
× 8
× 1
× 6
× 4
× 4
Silver Arrow SB-E
Extreme
Assembly package

Silver Arrow SB-E Extreme
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
Heatsink Body
Fan Clip
Screw Nut
Wrench
Mounting Plate
Intel Washer(small)
Backplate cap
Anti Vibration Pads
Metal Back Plate
M3 L10 Screw
Anchoring Mount
M3 L6 Screw
TY143 Fan
Intel 775/1155/1156/1366

2
The Ultimate Cooling Solutions!
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×6
Backplate cap ×1
Thermal paste ×1
Wrench ×1
TY 143 Fan ×2
Mounting Plate ×1
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×4
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-Cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17161514

3
Installation Instructions:
Step 1:
Step 2:
Step 4:
Step 3:
Step 5:
Step 1 : Back Plate Installation
Choose the platform (775/1155/1156/1366) you are in use. Make four M3L10 Screws go through the
Metal Back Plate from bottom towards top.And then place the Metal Back Plate on the table. Put the four
Washers (for Intel) around the Screw Cylinders.
Step 2 : 775 Back Plate cap
Note: When installing on a 775 platform, please
first insert the Back Plate Cap into the opening
on the Back plate. Make sure you have the Cap
facing downwards. (Only for 775).
Step 4 :Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to x the Anchoring
Mount on to the Screw Nuts.
Step 3 : Screw Cylinder Installation
Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four
holes around the processor socket. Cap the four
Screw Cylinders with the four Screw Nuts. Make
sure the side with a washer is facing the Back
Plate.
Step 5 :Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
1366
775 1156
1155
PWM Y-Cable ×1

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 6:
Step 7:
Step 8:
Step 8 : Installation completed
Connect the two TY-143 fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.
Step 7 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
Step 6 : Mounting Plate Installation
Place the Heat Sink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the Mounting Plate.
To PSU 4 Pin Molex
Connector

Silver Arrow SB-E Extreme
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
Heatsink Body
Fan Clip
LGA2011 Type B Screw Pillars
Wrench
Mounting Plate
Anti Vibration Pads
Anchoring Mount
M3 L6 Screw
TY143 Fan
Intel 2011

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×6
Backplate cap ×1
Thermal paste ×1
Wrench ×1
TY 143 Fan ×2
Mounting Plate ×1
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×4
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-Cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17161514

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Screw Pillar Installation
Screw on the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame
around the processor socket.
Step 2 :Anchoring Mount Installation
Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4
M3L6 Screws.
Step 3 :Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
PWM Y-Cable ×1

The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5:
Step 6:
Step 5 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
Step 4 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the Mounting Plate.
To PSU 4 Pin Molex
Connector
Step 6 : Installation completed
Connect the two TY-143 fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.

Silver Arrow SB-E Extreme
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
Heatsink Body
Fan Clip
Screw Nut
Mounting Plate
AMD Washer (big)
Backplate cap
Anti Vibration Pads
Metal Back Plate
M3 L10 Screw
Anchoring Mount
M3 L6 Screw
TY143 Fan
Wrench
AM2/AM2+/AM3/AM3+/FM1

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4
4 5
6
76
7 8
9
9
11
10
13
16
11
14
17
15
12
8
1312
Heatsink Body ×1
M3 L6 Screw ×6
Backplate cap ×1
Thermal paste ×1
Wrench ×1
TY 143 Fan ×2
Mounting Plate ×1
Metal Back Plate ×1
LGA2011 Type B
Screw Pillars x4
M3 L10 Screw ×4
AMD Washer (big) ×4
Anchoring Mount ×1
5
Screw Nut ×4
Anti Vibration Pad ×8
PWM Y-Cable ×1
10
Intel Washer (small) ×4
Fan Clip
x6
17161514

11
Installation Instructions:
Step 1:
Step 2:
Step 4:
Step 3:
Step 1 : Back Plate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screws go through the Metal Back Plate
from bottom towards top. And then place the Metal Back Plate on the table. Put the four Washers (for
AMD) around the Screw Cylinders.
Step 2 : 939 Back Plate cap
Note: When installing on a 939 platform, please
first insert the Back Plate Cap into the opening
on the Back plate. Make sure you have the Cap
facing downwards. (Only for 939).
Step 3 : Screw Cylinder Installation
Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four
holes around the processor socket. Cap the four
Screw Cylinders with the four Screw Nuts. Make
sure the side with a washer is facing the Back
Plate.
Step 4 :Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to fix the Anchoring
Mount on to the Screw Nuts.
Step 5 :Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
Step 5:
AMD

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 6:
Step 7:
Step 8:
Step 6 : Mounting Plate Installation
Place the Heat Sink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate.
Step 7 : Fan Installation
Pass one end of the Fan Clip through the mounting hole of the TY-143 Fan. Hook the Fan Clip through
the Fan Clip Slot. Pass the end of the Fan Clips through the mounting hole of the TY-143 Fan. Repeat
the procedure with the Fan Clip on the TY-143 Fan.
To PSU 4 Pin Molex
Connector
Step 8 : Installation completed
Connect the two TY-143 fans to the Male PWM end of the PWM Y-Cable. Then connect the female
PWM end of the PWM Y-Cable to the mainboard's PWM connector. Last connect the female 4 Pin
Molex connector of the PWM Y-Cable to the male PSU 4 Pin Molex Connector.

The Ultimate Cooling Solutions!
www.thermalright.com
TEL: [phone]
FAX: [phone]
EMAIL: [email protected]