Thermalright Macho Zero User manual

Thermalright
Macho Zero

× 1
× 1
4
4
8
× 1
× 1
× 1
× 2
× 2
× 4 × 1
× 4 × 4
× 7
× 5
× 4
× 4
Macho Zero
Assembly package

Macho Zero
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 775/1150/1155/1156/1366
Screw Nut
Mounting Plate
M3L6 Screw
Anchoring Mount
Intel Washer (small)
Mylar Film
Metal Back Plate
Motherboard
M3L10 Screw
Heatsink Body

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Macho Heatsink Body ×1
Ckill Factor III ×1 Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
Mylar Film ×1 white cotton gloves ×2

3
Installation Instructions:
Step 1:
Step 2:
Step 1 : Backplate Installation
Choose the platform (775/1150/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars go
through the Metal Back Plate and the Mylar lm from bottom towards top.And then place the Metal Back
Plate on the table. Put the four Washers (for Intel) around the Screw Pillars.
- Please use the included gloves during installation to avoid nger prints on heatsink body.
Step 2 : 775 Back Plate Cap
Note: When installing on a 775 platform, please rst insert the Back Plate Cap into the opening on
the Back plate, make sure you have the Cap facing downwards. (Only for LGA775 platform, all other
platforms go directly to Step 3).
Step 3 : Place the motherboard on top of the
Back Plate. See the four Screw Pillars go
through the four holes around the processor
socket.Cap the four Screw Pillars with the four
Screw Nuts.Make sure the side with a washer is
facing the Back Plate.
1366
775
1150
1155
1156
Step 3:
12
4
3
Step 4:
12
4
3
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to fix the Anchoring
Mount on to the Screw Nuts.

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 5: Step 6:
Step 7: Step 8:
Step 9: Step 10:
Step 8 : First, compress (squeeze it together) the
fan duct so that it can easily t between the Macho
heatsink and the system exhaust fan at the rear of
your case. Connect the end with the Thermalright
logo of the fan duct to the rear case exhaust fan.
Step 5 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly. (A
flat edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 9 : by expanding the fan duct to connect the
back end to the Macho heatsink.
Step 10 : Installation completed.
Step 6: Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make
Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the
Mounting Plate, one side at a time in several turns
to ensure balanced mounting.
Step 7: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.

Macho Zero
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 2011
Mounting Plate
M3L6 Screw
Anchoring Mount
Motherboard
Heatsink Body
LGA2011 Type B Screw Pillars

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Macho Heatsink Body ×1
Ckill Factor III ×1 Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
Mylar Film ×1 white cotton gloves ×2

7
Step 1:
Step 2:
Step 3:
Step 1 : Screw Pillar Installation
Place the motherboard (the processor installed) on top of the desk or a workbench. Fix the four included
LGA2011 Type B Screw Pillars into the heat-sink studs on the Intel ILM Assembly Frame around the
processor socket in a criss-cross pattern.
Step 2 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Pillars. Use the four M3L6 Screws to x the Anchoring Mount
on to the Screw Pillars, also in a criss-cross pattern to ensure balanced mounting.
1
1
2
2
4
4
3
3
Step 3 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. (A at edge,
like a business card or an old credit card would be benecial in spreading the thermal paste.)
Installation Instructions:
- Please use the included gloves during installation to avoid nger prints on heatsink body.

Macho Zero
The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5: Step 6:
Step 7: Step 8:
Step 6 : First, compress (squeeze it together) the
fan duct so that it can easily t between the Macho
heatsink and the system exhaust fan at the rear of
your case. Connect the end with the Thermalright
logo of the fan duct to the rear case exhaust fan.
Step 7 : by expanding the fan duct to connect the
back end to the Macho heatsink.
Step 8 : Installation completed.
Step 4 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate, one side at a time in several turns to
ensure balanced mounting.
Step 5 : Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.

Macho Zero
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
AM2/AM2+/AM3/AM3+/FM1/FM2
Screw Nut
Mounting Plate
M3L6 Screw
Anchoring Mount
Mylar Film
Metal Back Plate
Motherboard
M3L10 Screw
Heatsink Body
AMD Washer (big)

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Macho Heatsink Body ×1
Ckill Factor III ×1 Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
Mylar Film ×1 white cotton gloves ×2

11
Step 1:
Step 2:
Step 3: Step 4:
AMD
Step 1 : Backplate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screw Pillars go through the Metal Back
Plate and the Mylar lm from bottom towards top. And then place the Metal Back Plate on the table. Put
the four Washers (for AMD) around the Screw Pillars.
Step 2 : Back Plate Cap
Note: When installing on an AMD platform, please
rst insert the Back Plate Cap into the opening on the Metal Back plate, make sure you have the Cap
facing downwards.
Step 3 : Place the motherboard on top of the Back
Plate. See the four Screw Pillars go through the
four holes around the processor socket. Cap the
four Screw Pillars with the four Screw Nuts in
a criss-cross pattern.Make sure the side with a
washer is facing the Back Plate.
12
3
4
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to fix the Anchoring
Mount on to the Screw Nuts.
12
4
3
Installation Instructions:
- Please use the included gloves during installation to avoid nger prints on heatsink body.

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 5: Step 6:
Step 7: Step 8:
Step 9: Step 10:
Step 8 : First, compress (squeeze it together) the
fan duct so that it can easily t between the Macho
heatsink and the system exhaust fan at the rear of
your case. Connect the end with the Thermalright
logo of the fan duct to the rear case exhaust fan.
Step 5 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly. (A
flat edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 9 : by expanding the fan duct to connect the
back end to the Macho heatsink.
Step 10 : Installation completed.
Step 6: Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make
Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the
Mounting Plate, one side at a time in several turns
to ensure balanced mounting.
Step 7: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.

Macho Zero
13
Fan Installation (Optional)
Fan clips
Anti-Vibration Pad

Macho Zero
The Ultimate Cooling Solutions!
www.thermalright.com
14
Step 1:
Step 2:
Step 3:
Step 1 : Apply Anti-Vibration padding to 4 corners on the heat-sink.
Step 2 : Put the fan clips into the dents on two sides of the heat-sink body.
Step 3 : Fan installation completed.

Macho Zero
15
Technical Spec
Heatsink Specifications:
Dimension: Length 140mm x Width 102mm x Height 162mm
Weight: 710g
Heatpipe: 6mm heatpipe*6 units
Copper Base: C1100 Pure copper nickel plated
Fan Specification:
Dimension: L152mm x H140mm x W26.5m
Weight: 160g
Fan speed: 900~1300RPM (4-Pin PWM)
Fan noise: 17~21dBA MAX (4-Pin PWM)
Airflow: 28.3~73.6CFM MAX
Connector: 4 Pin (PWM Fan connector)

The Ultimate Cooling Solutions!
www.thermalright.com
16

The Ultimate Cooling Solutions!
www.thermalright.com
TEL: [phone]
FAX: [phone]
EMAIL: [email protected]