Thermalright TRUE Spirit 140 BW Rev.A User manual

Thermalright
TRUE Spirit 140 BW Rev.A

TRUE Spirit 140 BW Rev.A
Assembly Package
× 4
× 7
× 1
× 1
× 1
4
4
8
× 4
× 5
× 1
× 8
× 1
× 4
× 4
× 4
Chill Factor 2g
× 1

TRUE Spirit 140 BW Rev.A
1
Intel 775/1150/1155/1156/1366
Exploded View
Heatsink Body
14cm Fan Clip
TY147 FAN
M3 L10 Screw
Anti Vibration Pad
Mounting Plate
M3 L6 Screw
Anchoring Mount
Screw Nut
Intel Washer
(small)
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com

The Ultimate Cooling Solutions!
www.thermalright.com
2
1
1
2
2
3
3
4
4
5
5
6
6
7 8
9
9
10 11
10
13
16
14
15 16
11
13
12
15
14
7 8
12
Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
M3 L6 Screw ×7
Back Plate Cap ×1
Mylar ×1
Thermal Paste ×1
Intel Washer (small) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
Screw Nut ×4
14cm Fan Clip ×4
Anti Vibration Pad ×8
TY147 Fan ×1
Chill Factor 2g
Component

3
Installation Instructions:
Step 1:
Step 3: Step 4:
Step 2:
Step 4 : Place the motherboard on top of the Back
Plate. See the four Screw Pillars go through the
four holes around the processor socket. Cap the
four Screw Pillars with the four Screw Nuts in
a criss-cross pattern.Make sure the side with a
washer is facing the Back Plate.
Step 1 : Fan Clip Installation
Take out TRUE Spirit 140 heat-sink body from the box. Apply Anti-Vibration Paddings to 4 corners of
the Heatsink n stack. Pull both ends of the Fan clip and make them go through holes on the corners of
the heat-sink. Repeat for the second fan clip on the other side of the n stack . Leave the two fan clips
on the Heatsink Body for fan install later on. Do not remove them.
12
4
3
Step 3 : 775 Back Plate cap
Note: When installing on a 775 platform, please
rst insert the Back Plate Cap into the opening on
the Back plate, make sure you have the Cap facing
downwards. Only for LGA775 platform, all other
platforms go directly to Step 4.
Step 2 : Back Plate Installation
Choose the platform (LGA 775/1150/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars
go through the Metal Back Plate and the Mylar lm from bottom towards top.And then place the Metal
Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars.
1366
775
1150
1155
1156

Chill Factor 2g Chill Factor 2g
Chill Factor
2g
Chill Factor
2g
Step 6:
Step 7:
Step 8: Step 9:
Step 8 : Fan Installation
Place the included TY-147 fan onto the Heatsink
body. And then secure it with the Fan Clips, by
pulling the Fan Clips to place the four ends at the
four holes on the TY-147 fan.
Step 7 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate, one side at a time in several turns to
ensure balanced mounting.
Step 9 : Installation completed
Connect the TY-147 fans to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6 :Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
(A at edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 5:
Step 5 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts. Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.
12
4
3

TRUE Spirit 140 BW Rev.A
5
Exploded view
Heatsink Body 14cm Fan Clip
TY147 FAN
Anti Vibration Pad
Mounting Plate
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
M3 L6 Screw
Anchoring Mount
LGA2011 Type B
Screw Pillars
Intel 2011

The Ultimate Cooling Solutions!
www.thermalright.com
6
1
1
2
2
3
3
4
4
5
5
6
6
7 8
9
9
10 11
10
13
16
14
15 16
11
13
12
15
14
7 8
12
Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
M3 L6 Screw ×7
Back Plate Cap ×1
Mylar ×1
Thermal Paste ×1
Intel Washer (small) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
Screw Nut ×4
14cm Fan Clip ×4
Anti Vibration Pad ×8
TY147 Fan ×1
Chill Factor 2g
Component

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 3 : Screw Pillar Installation
Screw on the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame
around the processor socket.
Step 2 : Anchoring Mount Installation
Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4
M3L6 Screws.
Step 1 : Fan Clip Installation
Take out TRUE Spirit 140 heat-sink body from the box. Apply Anti-Vibration Paddings to 4 corners of the
Heatsink n stack. Pull both ends of the Fan clip and make them go through holes on the corners of the
heat-sink. Repeat for the second fan clip on the other side of the n stack . Leave the two fan clips on the
Heatsink Body for fan install later on. Do not remove them.
1
1
2
2
4
4
3
3

TRUE Spirit 140 BW Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
8
TRUE Spirit 140
Step 6:
Step 4:
Step 6 : Fan Installation
Place the included TY-147 fan onto the Heatsink body. And then secure it with the Fan Clips, by pulling
the Fan Clips to place the four ends at the four holes on the TY-147 fan.
Step 7 : Installation completed
Connect the TY-147 fans to the CPU PWM Fan socket on the motherboard. Installation complete.
Step 7:
Step 5:
Step 5 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make
Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the
Mounting Plate, one side at a time in several turns
to ensure balanced mounting.
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
(A at edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g

TRUE Spirit 140 BW Rev.A
9
Heatsink Body 14cm Fan Clip
TY147 FAN
M3 L10 Screw
Anti Vibration Pad
Mounting Plate
M3 L6 Screw
Anchoring Mount
Screw Nut
AMD Washer
(big)
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
AM2/AM2+/AM3/AM3+/FM1/FM2

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4
4
5
5
6
6
7 8
9
9
10 11
10
13
16
14
15 16
11
13
12
15
14
7 8
12
Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
M3 L6 Screw ×7
Back Plate Cap ×1
Mylar ×1
Thermal Paste ×1
Intel Washer (small) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
Screw Nut ×4
14cm Fan Clip ×4
Anti Vibration Pad ×8
TY147 Fan ×1
Chill Factor 2g

11
Installation Instructions:
AMD
Step 1:
Step 3: Step 4:
Step 2:
Step 4 : Place the motherboard on top of the Back
Plate. See the four Screw Pillars go through the
four holes around the processor socket. Cap the
four Screw Pillars with the four Screw Nuts in
a criss-cross pattern.Make sure the side with a
washer is facing the Back Plate.
Step 1 : Fan Clip Installation
Take out TRUE Spirit 140 heat-sink body from the box. Apply Anti-Vibration Paddings to 4 corners of
the Heatsink n stack. Pull both ends of the Fan clip and make them go through holes on the corners of
the heat-sink. Repeat for the second fan clip on the other side of the n stack . Leave the two fan clips
on the Heatsink Body for fan install later on. Do not remove them.
Step 3 : Back Plate Cap
Note: When installing on an AMD platform, please
rst insert the Back Plate Cap into the opening
on the Metal Back plate, make sure you have the
Cap facing downwards.
Step 2 : Back Plate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screw Pillars go through the Metal Back
Plate and the Mylar lm from bottom towards top.And then place the Metal Back Plate on the table. Put
the four Washers (for AMD) around the Screw Pillars.
12
3
4

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 6:
Step 7:
Step 8: Step 9:
Step 8 : Fan Installation
Place the included TY-147 fan onto the Heatsink
body. And then secure it with the Fan Clips, by
pulling the Fan Clips to place the four ends at the
four holes on the TY-147 fan.
Step 7 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate, one side at a time in several turns to
ensure balanced mounting.
Step 9 : Installation completed
Connect the TY-147 fans to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6 :Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
(A at edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 5:
Step 5 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts. Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.
12
3
4
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g

TRUE Spirit 140 BW Rev.A
13
Technical Spec
Heatsink Specifications:
Dimension: Length 155mm x Width 53.4mm x Height 165.15mm
Weight: 610g (Heatsink only)
Heatpipe: 6mm heatpipe*6 units
Copper Base: C1100 Pure copper nickel plated
Fan Specification:
Dimension: L152mm x H140mm x W26.5m
Weight: 160g
Fan speed: 900~1300 RPM (4-Pin PWM)
Fan noise: 17~21 dBA MAX (4-Pin PWM)
Airflow: 28.3~73.6 CFM MAX
Connector: 4 Pin (PWM Fan connector)

TRUE Spirit 140 BW Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
14

TRUE Spirit 140 BW Rev.A
15

TRUE Spirit 140 BW Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
16
The Ultimate Cooling Solutions!
www.thermalright.com
TEL: [phone]
FAX: [phone]
EMAIL: [email protected]