Thermaltake Water2.0 Extreme User manual

These warranties replace all other warranties, expressed or implied including,
but not limited to, the implied warranties of merchantability and fitness for a
particular purpose.
Thermaltake disclaims all other warranties, expressed or implied including,
without limitation, implied warranties of merchantability and fitness for a particular
purpose.
Some jurisdictions do not allow the exclusion of implied warranties so this
limitation may not apply to you. All expressed and implied warranties are limited in
duration to the limited warranty period. No warranties apply after that period, some
jurisdiction do not allow limitation on how long an implied warranty lasts, so this
limitation may not apply to you.
Limitations of liability, Thermaltake's responsibility under this, or any other
warranty, implied or expressed, are limited to repair or replacement, as set forth
above. These remedies are the sole and exclusive remedies for any breach of
warranty. Thermaltake is not responsible for direct, special, incidental, or
consequential damages resulting from any breach of warranty or under any other
legal theory including, but not limited to, lost profits, downtime, goodwill, damage
to or replacement of equipment and property, and any cost of recovering,
reprogramming, or reproducing any program or data stored in or used with a
system containing Thermaltake product. Some jurisdictions do not allow the
exclusion or limitation of incidental or exclusions may not apply to you.
Extent of limited warranty, Thermaltake does not warrant that your product will
be free from design defects or errors known as "ERRATA". Current characterized
errata are available upon request. This limited warranty does not cover any costs
relating to removal or replacement of any part that is soldered or otherwise affixed
to your system's motherboard. This limited warranty does not cover damages due
to external causes, including accidental, problems with electrical power, usage not
in accordance with product instructions, misuse, neglect, alteration, repair,
improper installation, or improper testing. Nor is Thermaltake held liable for any
bodily damage that may result during the installation, maintenance, repair, or is
otherwise associated with this product, Thermaltake is free from any legal actions
that may result in death, pain and anguish, or any other form of personal damage
that may occur by purchasing this product.
You, the buyer, agree to this warranty and its term set within its expressed and
implied limited warranty. This limited warranty gives you specific legal rights, and
you may also have other right that varies from jurisdiction to jurisdiction.
Limited Liability
Before installing Thermaltake Water2.0 Extreme Liquid Cooling System, we
strongly suggest you to read the manual throughly and make sure all
components are included in the package. Please do follow the installation
guide step-by-step.
Improper installation may cause serious damage to the system as well
as to the water cooling unit. Thermaltake will not responsible for any
damages due to incorrect installation and incorrect usage of this product.
CAUTION
English
English

English
English
Components
Back Plate x 1 (Intel
1366/1156/1155/775)
Retention Ring x 1 (Intel
2011/1366/1156/1155/775) Back Plate x 1 (AMD) Retention Ring
x 1 (AMD)
Mylar x 2 Grommet x 4 Screw x 8 (for fan) Plastic component x 4
Plastic component x 4 Screw x 4 (Intel
1366/1156/1155
/775 & AMD)
Screw x 4 (Intel 2011) Retention clip x 1
A B C D
E F G H
IJK L
Washer x 4
MScrew x 4
(for radiator)
N
Specification
CD x 1
OFan x 2 PWater 2.0 Extreme Unit x 1 Q
Compatibility (CPU Socket) Intel LGA 2011/1366/1155/1156/775
AMD FM1/AM3+/AM3/AM2+/AM2
Water Block Material Copper
Pump
Motor Speed ± 2800 150 RPM
Rated Voltage 12V
Rated Current 220 mA
Fan
Dimension 120 x 120 x 25 mm
Speed 1200~2000RPM
Noise Level 27.36dBA(Max)
Rated Voltage 12V
Rated Current 0.5 A
Max. Air Flow 81.32CFM
Connector 4 Pin
Radiator
Dimension
Material Aluminum
Tube
Length 326 mm
Material Rubber
Weight
270 x 120 x 38.3mm
1,150g

English
English
Software Installation
Installation Complete
Components Check
Install Radiator
Fan and Pump Connection
In order to ensure convenience and safety , following the
installation procedure below is strongly recommended.
Pump Installation
Intel LGA 2011
Intel LGA 1366/1156/1155/775
AMD FM1/AM3+/AM3/AM2+/AM2
Installation steps Pump Installation
Snap top (H) and bottom (I) plastic
component together on to the 4 side of
socket ring (B), follow by placing the
screws (K) into the openings on the ring.
Note:
The letters LGA2011
must be seen when
snapping the bottom (I)
** Please remove the transparent cap in front of the pump when installing
on to the CPU, and be careful not to touch the thermal paste.
Attach Retention Ring (B) to Pump，and
snap the retaining clip (L) to the retention
Ring, locking the ring to pump.
Placed the composed pump on to the
CPU and use hand to screw (K) until its
tight, user may use screw driver for
tightening.
For Intel LGA 2011
K
H
I
B
1
P1.
P2.
P3.
P4.
P5.
P5.

English
English
Pump Installation
For AMD FM1/AM3+/AM3/AM2+/AM2
Pump Installation
For Intel LGA 1366/1156/1155/775
Please check the socket
type match CPU and
choose the right opening
to place (A) into it.
Stick Mylar(E) on the
back of the (A)and
place the four grommets
(F) on to the corresponding
openings.
Snap top (H) and bottom (I) plastic component
together on to the 4 side of socket ring (B),
follow by placing the screws (J) into the
openings on the ring.
** Please remove the transparent cap in front of the pump when installing
on to the CPU, and be careful not to touch the thermal paste.
Attach Retention Ring
(B) to Pump，and
snap the retaining clip
(L) to the retention
Ring, locking the ring
to pump.
Placed the
composed pump on
to the CPU and use
hand to screw (J)
until its tight, user
may use screw
driver for tightening.
Stick Mylar(E) on the
back of the (C)and place
the four grommets (F) on
to the corresponding
openings.
Stick the composed
Back Plate (C) on to
the back of the
motherboard.
Snap top (H) and bottom (I) plastic
component together on to the 4 side of socket
ring (D), follow by placing the screws (J) into
the openings on the ring.
** Please remove the transparent cap in front of the pump when installing
on to the CPU, and be careful not to touch the thermal paste.
Attach Retention Ring
(D) to Pump，and snap
the retaining clip (L) to
the retention Ring,
locking the ring to pump.
Placed the composed
pump on to the CPU
and use hand to screw
(J) until its tight, user
may use screw driver
for tightening.
Notice:
The letters of the socket
must be seen when
snapping the bottom (I)
Stick the
composed Back
Plate (A) on to the
back of the
motherboard.
Notice:
The letters AMD2/3
must be seen when
snapping the bottom (I)
F
A
E
J
H
I
B
E
C
F
DJ
H
I
23

English
English
Connect the Fan and Pump
Software Installation
Radiator Installation
Mount the Radiator and Fan on to the Chassis.
Note：Notice the airflow direction (As the photo illustrates). Connect the fans to pump fan output cable.
Connect the Pump Power Cable onto
nearest CPU fan header of motherboard.
Connect USB cable to motherboard.
Install software.
Screw
Washer
N
M
Fan cable
45
Screw G