Thermasol SEAT-S-GR User manual
Specications subject to change without notice. 81183 6/15
Page 1
ank you for purchasing the ermaSol™ Shower Seat. We are
condent that you will nd the unique design and durable construction
of this product to be of great assistance in your daily routine.
To fully enjoy your ermaSol™ Shower Seat, please take a few moments
to read these instructions. You should store these instructions in a safe
place for future reference.
SAFETY CONSIDERATIONS
CAUTION: It is your responsibility to see that your ermaSol™
Shower Seat is properly assembled, installed, and cared for. Failure to
follow instructions in this manual could result in serious injury. Some
surfaces can be slippery when wet - use this product with caution.
THERMASOL™ SHOWER SEAT INSTALLATION / MAINTENANCE
e ermaSol™ Shower Seat should only be installed in areas where
the mounting surface is structurally sound. Strengthening modications
may be required (see page 3 for details). ermaSol™ Shower Seat
should not be installed in berglass / acrylic shower enclosures with
insucient stiness and strength. Should not be installed into metal
studs. If you are not equipped to undertake the outlined work we
recommend that you have your ermaSol™ Shower Seat installed by
a qualied contractor. Seat should only be used for sitting upon - not
to be used for other purposes. Do not install seat in locations where
seated user and seat are close to direct steam or hot water emissions.
Suggested maximum user weight 500lbs/227kg, however this rating
is conditional upon suitable fasteners and supporting surface. One
person maximum capacity. WOOD CONTACT SENSITIVITY -
some people may experience a skin rash or other reaction due to
contact with certain types of wood. If unsure, test rst.
CLEANING & MAINTENANCE - Clean seat with water, and then
wipe dry using a so cloth. Do not use abrasive cleaning products.
WARRANTY
is shower seat is covered by a one year limited warranty with the
exception of hand grips which are subject to normal wear. Buyer hereby
indemnies, agrees to hold harmless and defend the manufacturer/
distributor of the ermaSol™ shower seat from and against any and
all liabilities, claims, (founded and unfounded), losses, damages, costs
and expenses (including without limitation consequential damages and
reasonableprofessionalfees)resultingfrombuyersspecication,application,
or improper use of goods described hereon; buyers omission or neglect.
e manufacturer/ distributor of the ermaSol™ shower seat does not
assume any liability for damage resulting from services performed by
others or faulty installation, misuse or misapplication of goods.
e manufacturer/ distributor of the ermaSol™ shower seat
shall not be liable for prospective prots or special, indirect, or
consequential damages, or for the cost of any corrective work
done without prior approval. Manufacturer/ distributor of the
ermaSol™ shower seat total liability hereunder shall in no
event exceed the purchase price of the goods specied hereon.
WOOD PANEL WARNING
In order to retain the natural beauty of the Bamboo, each slat is nished
with an extremely durable 2-part oil
nish that does not contain volatile organic compounds (VOCs) or
other harmful chemicals.
A light brown or red discoloration may be noticed in water exposed to
the wood, and is due to an excess of pigments (natural oils) in the wood
reacting with minerals present in certain types of water (well water,
hard water, etc.). is discoloration is a natural reaction oen referred
to as leaching and should fade over time. e applied oil nish also
reduces the eects of leaching. If unsure, test wood in local water prior
to installation.
TIPS FOR DRILLING INTO TILE
• Use carbide tipped masonary drill on ceramic, or consider
a diamond tip drill for porcelain tile.
• If possible, drill a smaller pilot hole rst.
• Be careful to prevent the drill from moving when you rst start it
rotating - use duct tape or a wood guide on the surface of the tile to hold
the drill from walking sideways.
• A variable speed drill on slow is best to start the hole. Do not apply too
much pressure when drilling. Do not use a hammer drill.
• e screws listed as #10 typically use a hole diameter of 1/8”
(3mm) into the support structure (wood studs, blocking, etc.).
e clearance hole through tile, etc. would be a minimum of
13/64” (5mm).
MOUNTING LOCATION
We strongly recommend that you give some thought as to the
optimal location of your ermaSol™ Shower Seat before
installation. e following suggestions are oered for your
consideration, however, it is recommended to consider advice
from the appropriate healthcare professional for locating of any
support product. Also, consider the following when determining
the optimal mounting location:
1. Move mounting location to match structure behind the wall.
2. Avoid electrical / plumbing behind the wall.
3. Where possible, drill through tile - not through grout.
e ermaSol™ Shower Seat is to be mounted on surfaces
perpendicular to each other (i.e. in a Shower). If the holes on the
bracket do not align with the wood studs, we recommend
strengthening modications to be done (see Page 3 for
recommendations). When determining the seat height,
consider the height of the user and their capabilities
(NOTE: ADA guideline species seat height of 17-19” above the
nished oor).
CLEANING AND MAINTENANCE
e back panels of the ermaSol™ Shower Seat are removable to allow
for cleaning of the wall behind the seat. Clean seat with water, and then
wipe dry using a so cloth. Do not use abrasive cleaning products.
ermaSol™ 18” Wide Bamboo Shower Seat
Installation Instructions: SEAT-S-GR
TOOLS REQUIRED
• Level • Personal Protective Eyewear • Center Punch • Hammer • Carbide
tip drill suitable for tile • Stud Finder • Protective blanket
Specications subject to change without notice. 81183 6/15
Page 2
INSTALLATION INSTRUCTIONS
Place a blanket down in the area that you will be installing
the ermaSol™ Shower Seat to protect the shower or bathtub
surfaces from parts that may fall during installation.
A1. Identify the horizontal and vertical location of the
ermaSol™ Shower Seat. Specically, identify the location of the
top hole
on one side of the wall bracket as shown in of Figure 1 (a).
A2. Notch the tile accurately with a center punch as shown in
Figure 2. NOTE: A light tap is all that is required for punch to
make notch.
A3. Drill hole for appropriate fastener as shown in Figure 3.
Clear away debris from hole that could interfere with the seat
sitting ush with the wall.
A4. Secure wall bracket using appropriate fasteners. Ensure
the screw goes in as straight as possbile so the at head of
the screw is within the countersunk area as shown in Figure 4.
If it protrudes out, it may interfere with the sliding removal
of the backrest panels.
A5. Once attached, use level as shown in Figure 1 (b) to
ensure seat is straight. Identify the location of the top hole on
the opposite wall bracket. IMPORTANT: Ensure distance
between the wall brackets allows for easy sliding of the back
rest panels (do not cause brackets to bend inwards).
Repeat steps A2 thru A4 rst for the top hole on the opposite
wall bracket and ensure it is level. Repeat steps A2 thru A4
for the remaining holes.
NOTE: Perform a nal tighten and inspection of all fasteners.
Test the installation by pushing down / sitting on the seat.
A6. Once all screws are installed, the backrest panels can be
slid onto the wall bracket as shown below. Ensure the
orientation of each seat panel is correct (i.e. label on back of
panel should face wall).
Your ermaSol™ Shower Seat is now installed.
Specications subject to change without notice. 81183 6/15
Page 3
TIPS FOR LOCATING A WOOD STUD
• For drywall surfaces, use a stud sensor to locate a stud.
• For tile surfaces, try a stud sensor to locate a stud. If no stud is
found, measure 16” from a perpendicular wall. Drill a small hole
in the grout to ensure the stud has been found. If there is no stud
at this location, bend a piece of wire in a “L” shape and insert it
through the hole. Spin the wire to determine exactly where the
stud is located and mark its location. Patch all holes with silicone
to keep moisture out of the wall.
• If there is access to the backside of the bathroom wall (i.e.
through a closet), measure the stud location and transfer the
measurements into the bath area.
STRUCTURAL REINFORCEMENT SUGGESTIONS
NOTE: Due to variances in local construction methods and
materials used, details given below are suggestions only. Consult
the appropriate local contractor for specic advice. For concrete
walls, you may be able to install fasteners (such as a wedge
anchor) directly into the concrete wall without modication.
If there is access to the backside of the bathroom wall (i.e.
through a closet) and structural reinforcement is required,
consider cutting a hole in this backside wall to allow access
to the bathroom wall from behind (without having to remove
/ replace ceramic tiles).
1. Choose optimal mounting location of seat including height
(*H) and side to side location (L) as shown in Figure 1. NOTE:
If accessing the bathroom wall from the backside, transfer the
measurements for the support rail location to the backside wall
as shown in Figure 1b. Mark the height and location on the wall
for future reference.
*NOTE: ADA guideline species seat height of 17-19”
above the nished oor.
2. Find wall support studs & cut hole in wall board to expose
wall studs as shown in Figure 1. Suggested hole size is height
(A) of 18-24” (48-61cm) and width (B) corresponding to wall
stud spacing. Expose half width of each stud to facilitate re-
installation of wall board patch. IMPORTANT: Avoid any
utilities located in wall!
3. Fabricate a support frame structure from suitable wood pieces
as shown in Figure 2. Support frame width (D) should t snugly
within wall studs. Support frame height (E) should be from 24-
32” (61-81cm) high or more, depending on material and stiness
of wall studs. Locate top cross member (F) to position in line
with top hole on the wall bracket when seat is at install height
(H). Lower cross member (G) should be spaced at C = 14.125”
(37.465cm) center to center from top cross member (see Page
4 for dimensions of 2 center cross members). Use a generous
quantity of wood screws and glue to hold the support frame
structure together as shown. See alternative to support frame as
shown in Figure 3.
4. Insert support frame structure through hole in wall and secure
uprights to wall studs using a generous amount of wood screws.
5. Complete the ermaSol™ Shower Seat installation
instructions on Page 2. en, patch the wall cutout (if backside
access to bathroom, consider making an access panel for future
servicing) to match the surrounding wall as shown in Figure 4.
Specications subject to change without notice. 81183 6/15
Page 4
THERMASOL 18” BAMBOO SHOWER SEAT
Other manuals for SEAT-S-GR
1
