Thermo Scientific Barnstead GenPure xCAD Plus System User manual

50137064 Revision E June 2016
Thermo Scientific

Barnstead GenPure xCAD Plus

Ultrapure water system
Operating Instruction

©2016 Thermo Fisher Scientific Inc. All rights reserved.
Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the
product operation. This document is copyright protected and any reproduction of the whole or any part of this
document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific Inc.
The contents of this document are subject to change without notice. All technical information in this
document is for reference purposes only. System configurations and specifications in this document supersede
all previous information received by the purchaser.
Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or error-
free and assumes no responsibility and will not be liable for any errors, omissions, damage or loss that
might result from any use of this document, even if the information in the document is followed
properly.
This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This
document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of
Sale shall govern all conflicting information between the two documents.
Release history:
For Research Use Only. Not for use in diagnostic procedures.

Thermo Scientific GenPure iii
P
Preface
©2016 Thermo Fisher Scientific Inc. All rights reserved.
These operating instructions are protected by copyright. Rights resulting thereof, particularly reprint,
photomechanical or digital postprocessing or reproduction, even in part, are only allowed with the
written consent of Thermo Electron LED GmbH. 
This regulation does not apply to reproductions for in-plant use.
The contents of this operating instructions manual may change at any time and without any prior
notice. Concerning translations into foreign languages, the English version of these operating
instructions is binding.
Before you start to install and work with your ultrapure water system, please carefully read the
information that is given in these operating instructions on how it is to be installed and operated.
This is particularly important as we, the manufacturer, cannot accept liability for any damage
occurring as a result of incorrect operation of the system or from use of it for other than the specified
purpose.
Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use
in the product operation. This document is copyright protected and any reproduction of the whole or
any part of this document is strictly prohibited, except with the written authorization of Thermo
Fisher Scientific Inc.
The contents of this document are subject to change without notice.
All technical information in this document is for reference purposes only. System configurations and
specifications in this document supersede all previous information received by the purchaser.
Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or
error-free and assumes no responsibility and will not be liable for any errors, omissions, damage or loss
that might result from any use of this document, even if the information in the document is followed
properly.
This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser.
This document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and
Conditions of Sale shall govern all conflicting information between the two documents.

Preface
Legal Information
iv GenPure Thermo Scientific
Legal Information
Warranty
Thermo Electron LED GmbH warrants the operational safety and functions of the Thermo Scientific
Barnstead Ultrapure Water Systems only under the condition that:
• the system is operated and serviced exclusively in accordance with its intended purpose and as
described in these operating instructions,
• the system is not modified,
• only original spare parts, consumables and accessories that have been approved by Thermo
Electron LED GmbH are used (third-party spares, consumables or accessories without Thermo
Electron LED GmbH approval void the limited warranty),
• inspections and maintenance are performed at the specified intervals,
• an installation verification test is performed on commissioning the system for the first time and
repeated after each inspection and repair activity. 
The warranty is valid from the date of delivery of the system to the customer.
• The above mentioned warranty conditions are subject to the general terms and conditions of sale,
in effect at the time of purchase, which apply as well.

Specifications, terms and pricing are subject to change. Not all products are available
in all countries. Please consult your local sales representative for details.

Preface
Explanatory notes on the operating instructions
Thermo Scientific GenPure v
Explanatory notes on the operating instructions
EU Mark of Conformity
CSA - admission

Indicates a situation which, if not avoided, could result in damage to equipment or
property.

Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injuries.

Indicates a hazardous situation which, if not avoided, will result in death or serious
injuries.

General information! Particularly important notes are marked with this information
sign.
Risk of electric shock! Electrical work on the system is only to be carried out by qualified personnel.
Protective conductor connection.
Connect the power supply to an electrical socket with a protective connection.
Indicates a situation where protected gloves or clothing is needed.
Indicates a situation in which protective goggles must be worn.

Preface
Standards and Directives
vi GenPure Thermo Scientific
This information is valid for the system that is received.
For quick and correct service, please include the following information on all inquiries and
replacement parts orders which relate to your system:
• The serial number (located on the right side of the system on the nameplate)
•Thecatalognumber
Standards and Directives
The ultrapure water system complies with the following standards and directives:
• Low Voltage Directive 2014/35/EU
• EMC Directive 2014/30/EU
• ASTM D1193-6
• RoHs 2011/65/EU
Additionally, the ultrapure water system is in compliance with many other international standards,
regulations and directives not listed here. Should you have any questions regarding compliance with
national standards, regulations and directives applicable for your country, please contact your Thermo
Fisher Scientific sales organization.
Indicates a situation in which breathing protection must be worn.

Thermo Scientific GenPure 1
C
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Legal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Explanatory notes on the operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . v
Standards and Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Chapter 1 Transport and packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Examination on receipt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Complaints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Packing for return shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3 Extent of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Extent of assembly kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Available GenPure xCAD Plus versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
GenPure xCAD Plus bench version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
GenPure xCAD Plus wall version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 5 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 6 The installation area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 7 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connectors xCAD Client 30
Installation of GenPure xCAD Plus system, bench version . . . . . . . . . . . . . . . . 31
Installation of GenPure xCAD Plus system, wall version . . . . . . . . . . . . . . . . . . 35
Installation of an additional xCAD Client, bench version (optional) . . . . . . . . . 41
Installation of an additional xCAD Client, wall version (optional). . . . . . . . . . . 42
Wall mounting GenPure xCAD Plus system . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Mounting the power pack (voltage supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Installation examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Connection to an Ion exchanger DI 1500 (option) . . . . . . . . . . . . . . . . . . . . . 50
Contents
Installation of GenPure xCAD Plus system, bench version . . . . . . . . . . . . . . . . 31
Installation of GenPure xCAD Plus system, wall version . . . . . . . . . . . . . . . . . . 35
Installation of an additional xCAD Client, bench version (optional) . . . . . . . . . 41
Installation of an additional xCAD Client, wall version (optional). . . . . . . . . . . 42
W
all mounting GenPure xCAD Plus system . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Mounting the power pack (voltage supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Installation examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Contents
2GenPure Thermo Scientific
Chapter 8 Flow chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Chapter 9 How the system functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 10 Putting system into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Dispensing water from the dispensing valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Venting the 0.2 μm final filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Chapter 11 Operating elements xCAD Server and xCAD Client . . . . . . . . . . . . . . . . 57
Description of Display xCAD Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Flow chart of menu system control xCAD Server . . . . . . . . . . . . . . . . . . . . . . . 59
Description display xCAD Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Flow chart control unit xCAD Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 12 System control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Interval operating mode after switching on . . . . . . . . . . . . . . . . . . . . . . . . . 64
Non-stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Interval operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
UV-Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Water dispensing via volumetric control . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
OFF mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
User menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Feedwater measured value and limiting value. . . . . . . . . . . . . . . . . . . . . . . . 68
Ultrapure water limiting value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
UV-Lamp operating time and intensity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Ultrapure cartridge serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Rinsing the ultrafilter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Disinfection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Error history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Print out of Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Registering the xCAD Client to the xCAD Server . . . . . . . . . . . . . . . . . . . . 74
Entering a code number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
OEM Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Language selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Program selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Entering system version and serial number. . . . . . . . . . . . . . . . . . . . . . . . . . 76
Switching units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Switch temperature compensation off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Set the limiting value for temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Rinsing time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Change the disinfection time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Set the interval pump time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Circulating pump performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Set the interval rinse time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Nonstop duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Set the real-time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Set the sending interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Contents
Thermo Scientific GenPure 3
Data transmission via the RS 232 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Printer output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Standard message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Code message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Error message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Measuring cell error recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Code lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Chapter 13 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Change the ultrapure cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Disinfection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Change the ultrafilter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Structure of the UV-lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Change the UV-lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Change and autoclave the Final filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Autoclave the Final filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Chapter 14 Waste disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Chapter 15 Trouble shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Chapter 16 Replacement parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
GenPure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
xCAD Server/ xCAD Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Chapter 17 Consumable materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Chapter 18 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Chapter 19 Terminal assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Chapter 20 Maintenance records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Chapter 21 Contact Information Thermo Scientific. . . . . . . . . . . . . . . . . . . . . . . . . . 117
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

Contents
4GenPure Thermo Scientific

Thermo Scientific GenPure 5
1
Transport and packaging
Contents
•“Examination on receipt” on page 6
•“Complaints” on page 6
•“Packing for return shipment” on page 6
Do not pull the plastic foil over your head. Risk of suffocation.
Use the plastic foil only for packaging.

1Transport and packaging
Examination on receipt
6GenPure Thermo Scientific
Ultrapure water systems are carefully controlled and packed prior to dispatch, but damage could still
possibly occur during transport. When the system is to be carried by hand, two people must always do
this. Do not throw or tip the system.
Examination on receipt
• Check the completeness of the goods received against the delivery note.
.
Complaints
Should damage have occurred to the goods during transport:
• Immediately contact your delivery transport agency.
• Save the complete packaging, including the cardboard box, for a possible inspection of them
and/or return shipment of the system.
Packing for return shipment
If possible, use the original box and packaging material.
When these are no longer available:
• Protect the system from shock by packing it in a suitable bag or sheet in a strong cardboard box.

Does the packaging show signs of damage? Inspect the system for damage.
Packaging
System
xCAD Server

The time limit for claims is 6 days from the time of receipt of the goods. The right to
claim for damages ceases when this time has elapsed.
• Only a trained person is to be taken out the system out of operation.
• Prior to send back a operated system, empty the water and dry the system and
take out the cartridges.
• Pack the filter cartridges into a bubble wrap and/ or packaging foam include it
with the package of the ultrapure water system.

Thermo Scientific GenPure 7
2
Safety precautions
• Do not start to install and operate the system until you have read through the corresponding
information given in these operating instructions.
• Lifting and carrying the ultrapure water system, e.g. to the installation location, should be carried
out by two people. To lift it, each person takes hold of it under the base plate at two corners.
• The CE-mark is invalidated if constructional changes are made to the system, or if products of
other manufacturers are installed in it.
• Protect the system from frost. The temperature in the area in which the system is installed is not to
go below +2°C or above +40°C.
• Observe all appropriate rules and regulations, including the valid accident prevention regulations,
which are applicable at the location where the system is installed.
• The feedwater pressure must be at least 0.1 bar and at max. 6 bar or 1.45 to 87 PSI. When the
feedwater pressure is higher, install an external pressure reducer.
• A low pressure check valve is recommended to prevent back flow of feedwater from water system.
• A grounded 100-250V, 50/60Hz socket must be available (see “Technical specifications” on
page 19).
• Access to the power supply cord and plug may never be restricted or obstructed.
• The installation area must have a drain at floor level with at least a nominal out diameter of 63mm
or 2.481 inch (DN 50 pipe). Should no such drain be available it is recommend to install a water
watcher (only for European specification). Otherwise the manufacturer will not accept liability for
any possible water damage.

Observe these safety precautions for your own safety.
Thermo Scientific Barnstead Ultrapure Water Systems are modern water purification
systems intended solely for the treatment of potable water or water of ASTM Type II
quality. The water it produces is not fit for drinking.
Work may only be performed on the unit electronics when the unit has been
switched off and when ESD protection is in place. Only specially trained personnel
may work on the unit‘s electronics.

2Safety precautions
8GenPure Thermo Scientific
• If the system is to be at a rest for a longer time (e.g. long, holidays) switch the system off (unplug
the mains plug) and shut off the feedwater line.
Allowing the system to run with the water feed line closed would result in damage to the pump.
The manufacturer does not accept liability for such damage.
• Unplug the system from the power outlet for all Maintenance works on the system.
• The system must be subjected to rinsing and possibly also disinfection after longer rest periods.
Follow the directions given in the section “Rinsing the ultrafilter” on page 71.
• The surface or wall where the system is to be installed must have adequate load-bearing capacity
(check the capacity and stability of the wall). The weight of the ultrapure water system is given
under “Dimension and weight GenPure System” on page 20.
• The surface on which the unit is installed must be level and stable - not to exceed a maximum of
2% deviation from evenness is recommended.
• When installing the ultrapure water system, always ensure that there is adequate space all around
the unit (approx 30cm / 11.81 inch) to ensure that ease of use or replacement of materials (e.g.
filter change, connection) is possible at all times.
• Visually inspect the system at regular intervals. Clean up any water or spills found around the
system immediately
.

Never look directly into a switched-on UV-lamp, as UV-light endangers eyesight!
To avoid the risk of pinching, crushing cutting or electrical shock, never perform
maintenance on the unit without its protective housing, or while it is in operation.
Maintenance work on the system may only be performed by trained, authorized
specialists.
• Wear safety gloves when working with cleaning solution.
• If your skin should come into contact with a chlorine product, rinse it immediately with ample,
fresh water.
• The unit or system components, may heat up as a result of a defect. It is recommended to always
wear appropriate safety gloves to prevent skin damage or burns.
• Wear safety gloves when changing the UV-lamp, in order to prevent that your skin comes in
contact with the UV-lamp glass.
• Wear safety goggles when working with cleaning solution.
• If your eyes come into contact with a chlorine product, rinse them immediately with ample,
fresh water and immediately contact a physician.

2 Safety precautions
Thermo Scientific GenPure 9
• To avoid tripping ensure that the tubings do not lay over the floor.
• Apply the general rules of hygiene for laboratories when working with the system.
• Do not use oxidative cleaning agents when cleaning the system. They would cause damage to it.
• Proceed as follows when the system has a defect:
• Switch the system off and unplug the system from outlet.
• Shut off the feedwater supply.
• Contact your local service organization.
• Check the UV-lamp before initial start.
• If the UV-lamp is broken
• wear directly a breathing protector (filter category FFP3) and replace the UV-Lamp
• ventilate the room well.
The Hg content in the UV-lamp is so low so that no damage to the
environment can arise.

2Safety precautions
10 GenPure Thermo Scientific

Thermo Scientific GenPure 11
3
Extent of delivery
Contents
•“Extent of assembly kit” on page 12
•“Available GenPure xCAD Plus versions” on page 14

3Extent of delivery
Extent of assembly kit
12 GenPure Thermo Scientific
Extent of assembly kit
Ultrapure cartridge
Catalog no.: 09.2005
Final filter 0.2 μm
Catalog no.: 09.1003
To increase the lifetime of the filter a sterilization at 120 °C for
30min is recommended. The procedure for the filter can be
repeated up to 5 times.
Transformer-table power pack
Catalog no.:50149597
Universal Holder and Universal adapter
Catalog no.: 21.0007
Catalog no.: 21.0006
Feedwater connecting kit
Catalog no.: 25.0075

3 Extent of delivery
Extent of assembly kit
Thermo Scientific GenPure 13
Connecting Cord (US) Catalog no.: 50132200
Connecting Cord (british) Catalog no.: 50132203
Connecting Cord (euro) Catalog no.: 50132215
Mounting parts for wall mounting GenPure system and xCAD
wall version:
-Plug 4 x S6
Catalog no.: 21.0002 (for xCAD)
-Screw 4x40 mm or 4 x 1.57 inch
Catalog no.: 21.0001 (for xCAD)
-Plug 2 x S8
Catalog no.: 21.0035 (for GenPure system)
-Screw hook 2 x 5.2 x 50 mm or 5.2 x 1.97 inch
Catalog No.: 21.0057 (for GenPure system)
Sub-D extension cable, 25 pin, 5 m or 5.47 yards 
Catalog no.: 16.0375
PE hose, Ø8mm x 20 m or 0.31 inch x 21.87 yards
Catalog no.: 18.0036
Sub-D-extension cable, 9pin, 3m or 3.28 yards
Catalog no.: 16.0397

3Extent of delivery
Available GenPure xCAD Plus versions
14 GenPure Thermo Scientific
Available GenPure xCAD Plus versions
GenPure xCAD Plus bench version:
50136149 standard Basic system
50136150 UF Basic system + ultrafiltration module
50136151 UV Basic system + UV photooxidation
50136152 UV/UF Basic system + UV photooxidation + ultrafiltration
module
50136153 UV-TOC Basic system + UV-photooxidation and TOC
Measurement
50136146 UV-TOC/UF Basic system + UV-photooxidation and TOC
Measurement + ultrafiltration module