Thinkware X700 User manual

This product records videos while the vehicle is operating.
Read and follow the instructions in this guide to properly use and maintain the product.
User Guide
X700

Before using the product
About the product
This product records videos while the vehicle is operating. Use this product only for reference when
investigating incidents or road accidents. This product is not guaranteed to record and cloud service for
ALL events. The device may not properly record accidents with small impacts that are too minor to activate
the impact sensor or accidents with massive impacts that cause the vehicle’s battery voltage to deviate.
Video recording does not begin until the product is completely turned on (booted up). To ensure that all
vehicle events are recorded, wait until the product is completely booted up after turning it on, and then
begin operating the vehicle.
THINKWARE is not responsible for any loss caused by an accident, nor is it responsible for providing any
support regarding the outcome of an accident.
Depending on the vehicle's configuration or operating conditions, such as the installation of remote door
lock devices, ECU settings, or TPMS settings, some product features may not be supported, and different
firmware versions may influence the product's performance or features.
About the user guide
The information provided in the guide may change when the manufacturer updates its service policy. This
user guide is intended for THINKWARE X700 models only, and it may contain technical errors, editorial
errors, or missing information.
Copyrights
All rights for the content and maps in this guide are reserved by THINKWARE and are protected under
copyright laws. All unauthorized duplication, revision, publication, or distribution of this guide without
written consent from THINKWARE is prohibited and is eligible for criminal charges.
Registered trademarks
THINKWARE X700 is a registered trademark of THINKWARE.
Other product logos and service names in this guide are trademarks of the relevant companies.

3
Contents
Safety information 5
1. Product overview 6
1.1 Included items 6
1.1.1 Standard items 6
1.1.2 Accessories (sold separately) 6
1.2 Part names 7
1.2.1 Front camera (main unit) - front view 7
1.2.2 Front camera (main unit) - rear view 8
1.2.3 Rear camera (optional) 8
1.3 Removing and inserting the memory card 9
2. Installing the product 10
2.1 Installing the front camera (main unit) 10
2.1.1 Selecting an installation location 10
2.1.2 Securing the product 10
2.1.3 Connecting the power cable 12
2.2 Installing the rear camera (optional) 13
2.2.1 Selecting an installation location 13
2.2.2 Securing the rear camera 13
2.2.3 Connecting the rear camera cable 14
2.3 Installing the external GPS module (optional) 16
3. Using recording features 17
3.1 Turning the product on or off 17
3.2 Turning the LCD on or off 18
3.3 Learning about the file storage location 18
3.4 Using the continuous recording feature 19
3.5 Recording manually 19
3.6 Using parking mode 20
3.7 Using the Super Night Vision 21
3.8 About the screen layout 22
3.8.1 Live view screen 22
3.8.2 Home screen 23
3.9 Playing the videos 24
3.9.1 Playing on the product 24
4. Using Advanced Driver Assistance
Systems (ADAS) 27
4.1 The safety camera alert system
(optional external GPS module required) 28
4.2 The lane departure warning system (LDWS) 28
4.3 The forward collision warning system (FCWS) 29
4.4 The urban forward collision warning system
(uFCWS) 30
4.5 The front vehicle departure warning (FVDW) 30
5. Settings 31
5.1 Setting the camera 31
5.1.1 Setting the brightness of the camera
(brightness camera) 31
5.2 Setting recording features 31
5.2.1 Setting the continuous impact detection
sensitivity (cont. sensitivity) 31
5.2.2 Setting parking mode 32
5.2.3 Setting the Super Night Vision feature 32
5.2.4 Setting the parking impact
sensitivity (packing sensitivity) 32
5.2.5 Setting the motion detection sensitivity
(motion sensitivity) 33
5.2.6 Setting the record timer feature
(Off Timer) 33
5.2.7 Setting the battery protection feature
(battery protection) 33
5.2.8 Setting the battery cutoff voltage feature
(Off voltage) 34
5.2.9 Setting the battery protection feature for
wintertime (Wt Bty Protection) 34
5.3 Setting Road Safety Settings (ADAS) 34
5.3.1 Setting the safety cameras 35
5.3.2 Setting the mobile zone alert 35
5.3.3 Identifying the vehicle type 35
5.3.4 Initializing the ADAS calibration setting
(ADAS Settings) 35
5.3.5 Initializing ADAS calibration 36

4
5.3.6 Setting the lane departure warning
feature (LDWS) 36
5.3.7 Setting the lane departure detection
speed (LDWS speed) 36
5.3.8 Setting the forward collision detection
sensitivity (FCWS) 37
5.3.9 Setting the low speed forward collision
detection sensitivity (Low Speed FCWS) 37
5.3.10 Setting front vehicle departure
warning (FVDW) 37
5.3.11 Setting the ADAS Volume 38
5.4 Configuring the system settings 38
5.4.1 Setting the display language 38
5.4.2 Adjusting the system volume 38
5.4.3 Resetting the touchscreen
(Calibrate Touchscreen) 39
5.4.4 Adjusting the screen brightness
(LCD Brightness) 39
5.4.5 Setting the LCD Auto-Off 39
5.4.6 Setting the security LED 40
5.4.7 Setting the time zone 40
5.4.8 Setting the date (Set Date) 40
5.4.9 Setting the time (Set Time) 40
5.4.10 Setting the daylight saving time 41
5.4.11 Setting the speed unit 41
5.4.12 Setting the speed stamp 41
5.4.13 Partitioning the memory card 42
5.4.14 Formatting the memory card 42
5.4.15 Configuring the video overwriting
function 43
5.4.16 Initializing the system settings
(Reset Settings) 43
6. Accessing the product information 44
6.1 Understanding the product features 44
6.2 Viewing the product information 44
6.3 Accessing and configuring the GPS 44
7. Upgrading the firmware 45
8. Using the PC viewer 46
8.1 System requirements 46
8.2 PC viewer for Windows 46
8.2.1 Installing the PC viewer (for Windows) 46
8.2.2 PC viewer screen layout (for Windows) 47
8.2.3 Playing recorded videos on the
PC viewer (for Windows) 48
8.2.4 Video control menu overview
(for Windows) 49
8.3 PC viewer for Mac 50
8.3.1 Installing the PC viewer (for Mac) 50
8.3.2 PC viewer screen layout (for Mac) 51
8.3.3 Playing recorded videos on the
PC viewer (for Mac) 52
8.3.4 Video control menu overview (for Mac) 53
9. Troubleshooting 54
10. Specifications 55

5
Safety information
Read the following safety information to properly use the product.
Safety symbols in this guide
"Warning" - Indicates a potential hazard which, if not avoided, may result in injury or death.
"Caution" - Indicates a potential hazard which, if not avoided, may result in minor injury or property damage.
"Note" - Provides useful information to help users better utilize the product's features.
Safety information for proper use
•Do not operate the product while driving a vehicle. Distraction while driving may cause accidents and
result in injury or death.
•Install the product in places where the driver's view is not obstructed. Obstruction of the driver’s vision
may cause accidents and result in injury or death.
•Do not use damaged power cables. Doing so may result in electrical fire or electrocution.
•Disconnect the power cable from the product when it will not be used for an extended period. Failure to do
so may result in electrical fire or battery depletion.
•Ensure that the product is out of the reach of children and pets. If the product breaks, it may result in fatal
damage.
•Do not expose product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise.
•Avoid excessive humidity and do not allow any water to enter the product. Electronic components inside
the product may fail if exposed to humidity or water.
•Do not disassemble the product or subject the product to impact. Doing so may damage the product.
Unauthorized disassembly of the product voids the product warranty.
•Do not apply excessive force when pressing the buttons. Doing so may damage the buttons.
•Ensure you are inserting the memory card correctly before inserting it to the product. The memory card
slot or the memory card may be damaged if it is inserted incorrectly.
•When connecting the power cable to the product, ensure that the connection between the cable plug
and the power cable connector on the product is secure. If the connection is loose, the power cable may
become disconnected due to vehicle vibration. Video recording is not available if the power connector is
disconnected.

6
1. Product overview
1.1 Included items
Ensure that all the items are included when you open the product box.
1.1.1 Standard items
Front camera (main unit) Mount Car charger
Adhesive cable holder
MicroSD memory card
with adapter
(consumable)
Quick start guide & Warranty
/ CS information / User guide
(stored in the microSD card)
The standard items may change without prior notice.
1.1.2 Accessories (sold separately)
GND
ACC
BATTERY
Hardwiring cable External GPS receiver Rear camera
•GPS reception may be affected by interference from the vehicle's windshield, particularly those treated
with anti-UV protective coating, or built-in defroster. It is recommended that an external GPS receiver is
used when the GPS signal is weak or when you cannot get a GPS signal.
•To connect the external GPS receiver to the front camera, carefully remove the front camera's GPS port
cover with a pry tool or a small flat-head screwdriver to access the port.

Product overview
7
1.2 Part names
1.2.1 Front camera (main unit) - front view
DC-IN power
connector
Used to connect the
power cable.
V-IN input port
Used to connect the
rear camera.
Fixing bracket connector
Used to connect the fixing bracket.
GPS connector
Used to connect the external
GPS module (optional)
for additional features.
Speaker
Outputs the voice guide and buzzer
sounds to indicate the product’s status. Security LED
Indicates that the video is being recorded.
Front camera lens
Records the front view.
Power switch
Used to turn
on or off the product.
Memory card slot
Insert a memory card
to save recordings.

Product overview
8
1.2.2 Front camera (main unit) - rear view
Reset button
Insert the tip of a sharp object to reset
the product when an error occurs.
Microphone
Used for voice recording.
Status LED
Indicates the operating
status of the product.
Touchscreen
Used for setting the product or
viewing the recorded videos.
Gently touch the screen to make inputs on the touchscreen. The screen may be damaged if you apply
excessive force to the screen or if you touch the screen with a sharp object.
1.2.3 Rear camera (optional)
Adhesive fixing bracket
Used to fix the rear camera in the vehicle.
Rear camera lens
Records the rear view.
Security LED
Indicates that the video is
being recorded.
Connection port
Used to connect the rear camera cable.

Product overview
9
1.3 Removing and inserting the memory card
The memory cards are installed in the product at the factory. Follow the instructions to remove the memory
card from the product or to insert the memory card into the product.
Removing the memory card
Ensure that the product is turned off, and then gently
push the bottom of the memory card with your
fingernail. The lower part of the memory card will be
exposed.
Remove it from the product.
Inserting the memory card
Insert the memory card into the memory card slot,
paying attention to the direction of the memory card,
and then push the memory card into the slot until
you hear a click.
Before inserting the memory card, ensure that the
metal contacts on the memory card are facing
toward the lens of the product.
•Ensure that the product is turned off before removing the memory card. The recorded video files may be
corrupted or lost if you remove the memory card while the product is on.
•Ensure that the memory card is in the correct direction before inserting it into the product. The memory
card slot or the memory card may be damaged if it is inserted incorrectly.
•Use only authentic memory cards from THINKWARE. THINKWARE does not guarantee compatibility and
normal operation of third-party memory cards.
To prevent loss of recorded video files, periodically back up the video files on a separate storage device.

10
2. Installing the product
2.1 Installing the front camera (main unit)
Follow the instructions to properly install the product.
2.1.1 Selecting an installation location
Select an installation location that can record the
entire view in front of the vehicle without obstructive
the driver’s vision. Ensure that the front camera lens
is located in the center of the windshield.
20 cm
If a GPS navigating device installed on the dashboard is
present, its GPS reception may be affected depending
on the dashboard camera's installation location.
Adjust the installation location of the GPS navigating
device to ensure that the two devices are separated by
at least 8 inches.
2.1.2 Securing the product
Follow the instructions to secure the product at the installation location.
1
2
1
Align the fixing bracket to the bracket rail on the
product, and then slide it until you hear a click (
➊ ).
Then, carefully remove the protective film keeping
the lens clean (
➋ ).

Installing the product
11
2
After determining the installation location, wipe the installation location on the windshield with dry
cloth.
3
1
2
Remove the film from the adhesive tape on the
bracket, and then press the tape to the installation
location.
4
1
2
Remove the product from the bracket and push the
bracket against the windshield to ensure that the
bracket is firmly fixed.
5
Align the product to the bracket, and then slide it
into the locking position until you hear a click.
•The product may fall and be damaged during vehicle operation if it is not firmly fixed to the bracket.
•If you need to remove the bracket from the windshield to alter the installation location, be careful not
to damage the windshield’s film coat.
6
Set the vertical angle of the camera appropriately
and temporarily fix it by lightly turning the fixing
screw.
The camera angle must be adjusted again after the
installation is complete. Do not completely tighten
the fixing screw yet.

Installing the product
12
2.1.3 Connecting the power cable
When the engine and electrical accessories are turned off, connect the car charger.
The hardwiring cable (optional) must be professionally installed to the vehicle by a trained mechanic.
2
1
Connect the cigar socket power cable to the product’s
DC-IN power connector and insert the cigar jack into the
vehicle’s power socket.
The location and specifications of the power socket may differ by vehicle make and model.
•Use the authentic THINKWARE cigar socket power cable (optional). If you use another manufacturer's
cable, the product may be damaged or electrical fire or electrocution may result due to the voltage
difference.
•Do not cut or modify the power cable yourself. Doing so may damage the product or the vehicle.
•For safe driving, arrange the cables to prevent the driver's vision from being obstructed or interfering with
driving.

Installing the product
13
2.2 Installing the rear camera (optional)
Refer to the following instructions to properly install the rear camera.
2.2.1 Selecting an installation location
Select the location on the rear windshield where
there is no defrost grid wire and the camera can
record the entire rear view.
•For vehicles with a sunshade attached to the rear windshield, you must select the location where using
the sunshade will not interfere with camera operation.
•The adhesive part of the rear camera should not touch the defrost grid.
2.2.2 Securing the rear camera
Refer to the following instructions to secure the product to the installation location.
1
After determining the installation location, wipe the installation surface of the windshield with dry
cloth.
Check the installation location before you secure the rear camera to the rear windshield. After
securing the rear camera to the windshield, it is hard to remove the camera or change the installation
location due to the strong adhesive.
2
2
1
Remove the film from the fixing bracket's adhesive
tape and the camera lens.

Installing the product
14
3
Attach the product with the THINKWARE logo facing
the rear windshield and press the adhesive tape
firmly to secure the camera.
If the product is fixed in reverse, the rear view
will be recorded upside down.
4
Adjust the camera's vertical angle.
2.2.3 Connecting the rear camera cable
Power off the product and connect the rear camera cable to the front camera (main unit).
1
Connect one end of the rear camera cable to the
front camera’s V-IN connector.

Installing the product
15
2
Connect the other end of the rear camera cable to
the rear camera’s cable connector.
For safe driving, arrange the cables to prevent the driver's vision from being obstructed or interfering
with driving.
3
Turn on the ACC or starts the engine to check if the product is powered on. After the product is
powered on, the Status LED and the voice guide are turned on.
The product is powered on when electric accessories are turned on or the engine starts.
4
Check the camera angle on the LCD display and adjust the angle if necessary.

Installing the product
16
2.3 Installing the external GPS module (optional)
To activate the ADAS feature or record driving information (the speed and location), follow the instructions
and install the external GPS module on the upper part of the front windshield. Install the external GPS
module near the product, taking the module's cable length into account.
1
Remove the film from the back of the external GPS
module.
2
Attach the external GPS module's adhesive surface
to the upper part of the front windshield and press
the adhesive part firmly to secure it.
Before installation, make sure the external GPS module's cable length is sufficient and check the cable
routing path.
3
Connect the external GPS module to the product’s
GPS connector.
Check the GPS connector location again
before connecting the module. If you connect
the external GPS module to the DC-IN power
connector, the pins inside the port may be
damaged.
4
Turn on the ACC or starts the engine to check that the product is powered on. After the product is
powered on, the Status LED and the voice guide are turned on.
The product is powered on when electric accessories are turned on or the engine starts.

17
3. Using recording features
3.1 Turning the product on or off
The product is turned on automatically and continuous
recording starts when you turn on the ACC or start the
engine.
If you want to turn off the product, turn the Power switch
up.
To turn the power on again, turn the Power switch down.
Wait until the product is completely booted up after
turning it on, and then begin operating the vehicle.
The video recording does not begin until the product
is completely turned on (booted up).
Continuous recording and parking mode recording
The continuous recording and parking modes are the basic operation modes of the product.
Continuous recording starts when you start driving. While driving, videos are recorded continuously and
stored as 1 minute segments.
When you finish driving and turn off the engine, the recording mode switches to parking mode. In parking
mode, the product detects the impact to the vehicle and nearby motion and records every event.
Parking mode operates only when the continuous power cable is connected.

Using recording features
18
3.2 Turning the LCD on or off
This product allows you to check recorded videos in
real time on the LCD display by supporting the Live view
feature.
To turn off the display while maintaining the continuous
recording, briefly press the power button.
To turn on the display again, briefly press the power
button or gently touch the display.
You can set the time that the LCD will turn off automatically. Tap the Home button ( ) on the Live view
screen
>
Settings
>
System settings, and tap the button next to LCD Auto-Off.
LCD Auto-Off option Operation description
30 sec (default) The LCD will turn off automatically if you do not operate the product for 30 seconds.
10 min The LCD will turn off automatically if you do not operate the product for 10 minutes.
OFF The LCD is always on. (In this mode, you can turn the LCD on or off by briefly
pressing the Power button.)
3.3 Learning about the file storage location
Videos are stored in the following folders according to their recording mode. The folder names displayed on
the screen and created in the memory card are the same.
On the screen Continuous Continuous
Incident
Manual
Recording
Motion
Detection
Parking
Incident
Saved
Videos
In the memory card cont_rec evt_rec manual_rec motion_
timelapse_rec parking_rec saved_videos
Play videos on the product or a computer only. If you play videos by inserting the memory card in devices
such as a smartphone or a tablet PC, the video files may be lost.
A file name is composed of the recording start date and time, and the recording option.
Recording conditions
•F: Front camera
•R: Rear camera
REC_2018_07_01_10_25_30_
F.MP4
REC_2018_07_01_10_25_30_R.MP4

Using recording features
19
3.4 Using the continuous recording feature
Connect the power cable to the product’s DC-IN power connector and then turn on the vehicle’s electrical
accessories or start the engine. The status LED and the voice guide are turned on, and the continuous
recording starts.
During continuous recording, the product operates as follows.
Mode Operation description Status LED (STATUS)
Continuous recording During driving, videos are recorded in 1 minute segments and
stored in the cont_rec folder. (light on)
Incident continuous
recording*
When an impact to the vehicle is detected, a video is recorded
for 20 seconds, from the moment 10 seconds before the detection
to the moment 10 seconds after the detection, and stored in the
evt_rec folder.
(flickers)
* When an impact to the vehicle is detected during continuous recording, incident continuous recording starts with a
buzzer sound.
•Wait until the product is completely booted up after turning it on, and then begin operating the vehicle. The
video recording does not begin until the product is completely turned on (booted up).
•When incident continuous recording starts, the buzzer sounds as a notification. This function saves you
time when checking the LED indicators to know the operating status of the product.
•To use all recording modes, you must insert a memory card into the product.
•You can record bright and high resolution videos when parking at night by activating the Super night vision
feature.
3.5 Recording manually
You can record a scene you want to capture while driving and store it as a separate file. Manually recorded
videos are stored in the Manual record folder to prevent important data loss due to insufficient storage.
To start manual recording, tap the manual recording button ( ) on the Live view screen. Then, manual
recording will start with the voice guide. During manual recording, the product operates as follows.
Mode Operation description Status LED (STATUS)
Manual recording
When you tap the manual recording button ( ) a video will be
recorded for 1 minute, from 10 seconds before to 50 seconds after
pressing the button, and stored in the manual_rec folder.
(flickers)
To watch a manually recorded video, tap the Home button ( ) on the Live view screen
>
File List
>
Manual
Recording, and select a video to play.

Using recording features
20
3.6 Using parking mode
When the product is connected to the vehicle via the hardwiring cable (optional), the operating mode is
switched to parking mode with the voice guide after the engine or electrical accessories are turned off.
•Parking mode operates only when the hardwiring cable is connected. The hardwiring cable (optional)
must be professionally installed to the vehicle by a trained mechanic.
•To use all recording modes, you must insert a memory card into the product.
•Depending on the battery charging status of the vehicle, the duration of parking mode may differ. If you
want to use parking mode for an extended period, check the battery level to prevent battery depletion.
•You can record bright and high resolution videos while parking at night by activating the Super Night
Vision.
If you do not want to use parking mode or you want to change the mode settings, tap the Home button ( )
on the Live view screen
>
Settings
>
Record settings.
Refer to the following table to set the Parking Mode options.
Option Operation description Status LED (STATUS)
Motion
detection
No motion
or impact
detected
Monitors movement in the area or impacts to the vehicle. Video
will be recorded only when motion or an impact is detected. (solid)
Motion
detected
When a moving objects is detected while parking, a video is
recorded for 20 seconds, from 10 seconds before detection to 10
seconds after detection, and stored in the motion_timelapse_rec
folder.
(flickers)
Impact
detected
When an impact is detected while parking, a video is recorded for
20 seconds, from the moment 10 seconds before detection to 10
seconds after detection, and stored in the parking_rec folder.
(flickers)
Time
Lapse
No impact
detected
A videos is recorded at a rate of 2 fps for 10 minutes, compressed
into a 2-minute long file, and stored in the motion_timelapse_rec
folder. Since the video file recorded with this option is small, you
can record a long video.
(solid)
Impact
detected
When an impact is detected while parking, a video is recorded
for 100 seconds at a rate of 2 fps, from the moment 50 seconds
before detection to 50 seconds after detection, and stored in the
parking_rec folder after being compressed into a 20-second long
file. (The buzzer will sound.)
(flickers)
OFF The product is powered off when electric accessories and the
engine are turned off. Off