thomann Millenium MPS-850 User manual

MPS-850
e-drum set
assembly instructions

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
13.07.2018, ID: 428224

Table of contents
1 Safety instructions.......................................................................................................................................................................................................... 4
2 Scope of delivery.............................................................................................................................................................................................................. 5
3 Assembly.............................................................................................................................................................................................................................. 8
4 Protecting the environment.................................................................................................................................................................................... 15
Table of contents
MPS-850
3

1 Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.
Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke!
Never let children unattended use electrical devices.
Safety instructions
e-drum set
4

2 Scope of delivery
Before you assemble your drum set, make sure the contents of package is complete according to the following list and figure.
Item Qty.
1 1 Lateral support tube on the left
2 1 Lateral support tube on the right
3 2 Support tube for crossbeam
4 3 Cymbal brackets (Crash and Ride)
5 1 Upper horizontal connection tube
6 1 Lower horizontal connection tube
7 1 Left crossbeam
8 1 Right crossbeam
9 1 Crossbeam for Snare
10 2 Tom pad 1 (8", dual zone), tom pad 2 (8", dual zone)
11 2 Tom pad 3 (10", dual zone), tom pad 4 (10", dual zone)
12 1 Snare pad (dual zone)
13 1 Hi-hat controller
14 1 Connector for Hi-hat
15 1 Y cable for power supply
16 1 Hi-hat (with Edge and Choke)
17 2 Crash 1 (with Edge and Choke), Crash 2 (with Edge and Choke)
18 1 Ride (with Edge, Bell and Choke)
19 1 e-drum module Millenium MPS-850
20 1 Hi-hat stand with pedal
21 1 Bass drum pad pedal
22 1 Pedal beater
23 1 Bass drum pad
24 5 Mounting bracket for pads
25 1 Drum key
26 1 Set of drum sticks
Scope of delivery
MPS-850
5

Item Qty.
27 5 Velcro tape
28 1 Thumb screw, long
29 2 Thumb screw, short
30 1 Multi-cable for connecting the pads to the e-drum module
31 1 Plug-in power supply
32 2 Single connection cable for tom 4 and crash 2
33 1 Assembly instructions e-drum set
34 1 User manual e-drum module
Scope of delivery
e-drum set
6

Scope of delivery
MPS-850
7

3 Assembly
Overview
Loosen the screws of the clamps before sticking the tubes together. Mount the various elements in the specified sequence. The
final positions of the components are shown in the illustration below.
10 Tom pad 1 (8"), tom pad 2 (8")
11 Tom pad 3 (10"), tom pad 4 (10")
12 Snare pad
13 Hi-hat controller
16 Hi-hat pad
17 Crash 1, crash 2
18 Ride
19 e-drum module Millenium MPS-850
20 Hi-hat stand with pedal
21 Bass drum pad pedal
23 Bass drum pad
Assembly
e-drum set
8

Assembling the rack
CAUTION!
Danger of cuts on hands and fingers
When connecting the parts, take care for sharp edges on the metal tubes, screws etc.
1. Attach the horizontal connection tubes (5, 6) to the lateral support tubes (1, 2).
2. Then tighten the mounting screws with the drum key (25).
1. Attach the two side crossbeams of the rack (7, 8, 9) in the provided mounting clamps.
2. Attach the crossbeam support tubes (3) in the provided mounting clamps. Make sure that the ends of the support tubes (3)
are resting on the floor.
Assembly
MPS-850
9

3. Then tighten the mounting screws.
1. Position the mounting brackets (24) for the individual pads. Then tighten the mounting screws.
2. Turn the mounting brackets (24) in the right position for mounting the pads. Then tighten the mounting screws.
1. Insert the brackets (4) for the cymbals (Crash, Ride) into the provided mounting clamps on the rack. Fasten the brackets
using the mounting screws at the desired height.
2. Loosen the retaining screws on the bracket joints and turn the brackets into the desired playing positions. Then retighten
the locating screws firmly.
Assembly
e-drum set
10