thomann Millenium SeriesMPS-750 Mesh set User manual

MPS-750 Mesh Set
e-drum set
assembly instructions

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Strasse 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
04.04.2017, ID: 372716 (V2)

Table of contents
1 Safety instructions.......................................................................................................................................................................................................... 4
2 Scope of delivery.............................................................................................................................................................................................................. 5
3 Assembly.............................................................................................................................................................................................................................. 6
4 Protecting the environment.................................................................................................................................................................................... 12
Table of contents
MPS-750 Mesh Set
3

1 Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.
Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke!
Never let children unattended use electrical devices.
Safety instructions
e-drum set
4

2 Scope of delivery
Before you assemble your drum set, make sure the contents of package is complete according to the following list.
Millenium MPS-750 Mesh Set
ne-drum module Millenium MPS-750
n1 × mesh snare pad, 10", dual zone
n3 × mesh tom pads, 10", dual zone
n1 × kick pad, 8"
n1 × hi-hat pad, 8"
n2 × crash pad with choke function, 12"
n1 × ride pad with choke function, 14", triple zone
nHi-hat controller
nBass drum pedal
nRack with pad brackets (1 × L-rod, 3 × hexagonal bars) and cymbal holders (1 × short, 3 × large)
nComplete pad cabling
nMains power adapter
Scope of delivery
MPS-750 Mesh Set
5

3 Assembly
Overview
Loosen the screws of the clamps before sticking the tubes together. Mount the various elements in the specified sequence. The
positions of the pads, cymbals, etc. are shown in the illustration below.
Assembly
e-drum set
6

Assembling the rack
CAUTION!
Danger of cuts on hands and fingers
When connecting the parts, take care for sharp edges on the metal tubes, screws etc.
1 Align the upper and lower bracket for the connecting tubes (1, 2) of the two feet (3) of the rack in height and
according to the desired playing position. Insert the connecting pipes (1, 2) as shown and tighten the mounting
screws.
2 Insert the side arms (4) into the middle brackets of the two feet (3) of the rack. Make sure that the horizontal tubes
form a continuous arch.
3 Attach the two lateral supporting tubes (7) of the rack to the mounting brackets of the side arms (4). Make sure
that the ends of the support tubes are resting on the floor. Then tighten the retaining screws.
4 Position the mounting clamps (10/L-pieces, 11/hexagonal bars) for the individual pads. Then tighten the retaining
screws.
5 Turn the L-rods into a suitable position for mounting the pads. Then tighten the retaining screws.
Assembly
MPS-750 Mesh Set
7

6 Insert the three short brackets (9) and the long bracket (8) for the cymbals as shown into the designated
mounting clamps on the rack. Secure the supports at the desired vertical position using the retaining screws.
7 Loosen the retaining screws on the bracket joints and turn the brackets (8, 9) into the desired playing positions.
Then re-tighten the retaining screws.
Mounting pads on the rack
1 Attach the supplied retaining elements (one L-piece, three hexagonal rods) to the pads.
2 Insert the retaining elements into the clamps provided on the rack.
3 Align the pads on the rack to meet your needs and tighten the locking screws of the pad brackets and the pad
clamps on the rack firmly and evenly.
Assembly
e-drum set
8

Mounting cymbals on the rack
1 Insert the three cymbal holders (3 × long, 1 × short) as shown into the clamps provided on the rack.
2 Tighten the bolts on the clamps firmly and evenly.
3 Unscrew the wing nuts from the cymbal holders and take the flat and felt washers off the holders.
4 Place the cymbals on their supports as illustrated.
5 Place the flat and felt washers on the cymbals and fix the four cymbals with the associated wing nuts on the
holders.
Assembly
MPS-750 Mesh Set
9

Bass drum pedal, hi-hat
1 Screw the pedal and the pad as shown using the supplied screws.
2 Place the beater into the hole provided on the rotary head of the kick drum pedal and tighten the clamp with the
drum key firmly.
3 Position the unit in a comfortable playing position in front of the rack.
4 Position the hi-hat pedal to the left of the bass drum pad in a comfortable playing position in front of the rack.
Assembly
e-drum set
10