thomann Thon Studio Series User manual

Thon Studio Producer Desk / FPY
studio desk
assembly instructions

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
17.11.2021, ID: 503586, 503587, 496045, 496043, ...

Table of contents
1 Safety instructions.......................................................................................................................................................................................................... 4
2 Scope of delivery.............................................................................................................................................................................................................. 5
3 Installation.......................................................................................................................................................................................................................... 6
4 Technical specications............................................................................................................................................................................................. 15
5 Protecting the environment.................................................................................................................................................................................... 16
Table of contents
Thon Studio Producer Desk / FPY
3

1 Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children.
Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the product. They could swallow the pieces
and choke!
Never let children play unattended with the product.
CAUTION!
Risk of injury due to heavy weight
Due to the heavy weight of the studio desk, at least two persons are required for transport and assembly.
CAUTION!
Risk of injury to the hands
When assembling and screwing the individual parts, pay attention to sharp edges on tools, screws and components.
Safety instructions
studio desk
4

2 Scope of delivery
Before you assemble the studio desk, make sure the contents of package is complete according to the following list.
n2 × side panel
n1 × tabletop
n1 × pull-out board
n2 × pull-out rails
n1 × monitor bridge
n3 × monitor bridge plank
n1 × stabilizing panel
n1 × rear wall for cable channel
n1 × bottom panel for cable channel
n4 × rack rails, 3 RU, stepless, equipped with nuts and rubber piping
n8 × woodscrew for rack rails
n8 × Euro screw 6.3 × 16 for pull-out rails
n40 × wooden dowel
n40 × connector housing
n40 × connector bolts
n4 × base (only for item no. 496043, 496045)
n4 × cable feed-through (only for item no. 503586, 503587)
n1 × assembly instruction
Scope of delivery
Thon Studio Producer Desk / FPY
5

3 Installation
Place all components on a suitable mounting surface for mounting. Use a soft padding to prevent damages to the surfaces.
Overview
The following gure shows an overview of the individual components.
ö #
(
*
%
)
&
AB C EFG
'
$
D
+
,
1 Left side panel 10 Pull-out rails
2 Right side panel 11 Rack rail
3 Rear wall for cable channel A Connector bolt
4 Bottom panel for cable channel B Connector housing
5 Stabilizing panel C Wooden dowel
6 Pull-out board D Euro screw 6.3 × 16
7 Table top E Woodscrew for rack rails
8 Monitor bridge plank F Base (only for item no. 496043, 496045)
9 Monitor bridge G Cable feet-through (only for item no. 503586,
503587)
Installation
studio desk
6

Preparing the components
Insert the connecting bolts and connector housings into the holes provided in the side panels (6 × connecting bolt, 4 × connector
housing).
Position all connector housings so that the respective connecting bolts can be completely sunk into the holes and the arrow posi‐
tion of the connector housings points towards the hole.
Place two feet with sleeves into each of the holes provided in the side panels (only for item no. 496043, 496045)
ö
F#
1 Left side panel B Connector housing
2 Right side panel F Foot
A Connector bolt
Installation
Thon Studio Producer Desk / FPY
7

Place the connecting bolts, the connector housings and the wooden dowels into the holes provided in the rear wall for the cable
channel (4 × connecting bolts, 8 × connector housing , 8 × wooden dowel).
Place the connector housings, the connecting bolts and the wooden dowels into the holes provided in the bottom panel for the
cable channel (8 × connector housing, 8 × wooden dowel).
Position all connector housings so that the respective connecting bolts can be completely sunk into the holes and the arrow posi‐
tion of the connector housings points towards the hole.
$
%
3 Rear wall for cable channel B Connector housing
4 Bottom panel for cable channel C Wooden dowel
A Connector bolt
Place the connector housings and the wooden dowels into the holes provided in the stabilizing panel (4 × connector housing, 4 ×
wooden dowel).
&
5 Stabilizing panel C Wooden dowel
B Connector housing
Installation
studio desk
8

Insert the twelve connecting bolts into the holes provided in the bottom side of the tabletop.
(
7 Table top A Connector bolt
Assembling the components
Assemble the rear wall and the bottom panel for the cable channel and tighten the connector housings clockwise to lock the
connection with the inserted connecting bolts.
$
%
3 Rear wall for cable channel 4 Bottom panel for cable channel
Installation
Thon Studio Producer Desk / FPY
9

Place the assembled cable channel and the stabilizing panel onto the connecting bolts of the right side panel and tighten the
connector housings clockwise to lock the connection with the inserted connecting bolts.
Place the left side panel onto the cable channel and the stabilizing panel and tighten the connector housings clockwise to lock
the connection with the inserted connecting bolts.
#
&%$
1 Left side panel 4 Bottom panel for cable channel
2 Right side panel 5 Stabilizing panel
3 Rear wall for cable channel
Installation
studio desk
10