THOMSON DTI6300 User manual

36336330 DVBS IB DTI6300 C MM N USER MANUAL R=NA

3
Contents
10 Safety Information
11 Accessories
12 Introduction
13 Remote Control
14 Connections
16 Basic peration
17 Using the Quick TV Guide
18 Using the Menus
19 Using the Programme Guide
21 Top Up TV Anytime
22 Using your Programme Library
24 Using Planned Recordings
26 Recorder Functions
27 Set-Up
30 Customising Top Up TV Anytime
34 Troubleshooting
37 Technical Specifications
37 Product Details
38 Index
Safety Information
Quick Start Guide
Getting Started
Using Your DTR
Setting Up
Information
Index
Turn on/off sound (on
the TV).
“Quick” key to the
Top Up TV services.
Sets the remote
control to DTR mode.
Displays the TV
listings screen.
Controls the TV sound
level.
Navigation in
menus and
programmes
(up/down for
channels, Left/right
for time).
Takes you from
delayed TV in
memory to live TV.
Rewind and -24Hr in
the TV listings.
Stop recording or
playback.
Current programme
information. Skip back in
recordings.
Controls the Audio & Video
signals sent to the TV.
Used to select the
corresponding colour
option shown on the
screen.
Turns the DTR (or TV)
on or off.
Sets the remote
control to TV mode.
Display the recorded
programmes screen.
Displays the DTR main
menu.
Up/down channel or
page (in menus).
Chooses the
highlighted option or
confirms your
selection. Also
activates Quickfind
(fast channel
selection).
Navigates back up
from menus.
Fast forward and
+24Hr in the TV
listings.
Pause/ Play a
recording or pause
live TV.
Top half is Pause
Bottom half is Play
Make an instant
recording of a current
programme by pressing
and holding for 3
seconds.
Access digital text
services. Skip forward
whilst watching
recordings.
Subtitles on or off.
Enter channel
numbers or
information into
menus.
Enter channel numbers or
information into menus and
“swap” between tuners and hard
disk drive.
4Quick Start Guide

5
Quick Start Guide
AQuick-Start Guide to setting up your
Thomson Top Up TV+ Digital TV Recorder
First things first
Did the retailer check your postcode for Digital TV reception?
If not, you should contact your retailer or try one of the following to ensure
you live in a Freeview coverage area:
• Text your postcode to 83331 (standard rates apply)
• Visit www.freeview.co.uk or www.dtg.org.uk/consumer
• Call Freeview on 08708 809980
Please note:
In order to receive the best digital signal, you may need an aerial upgrade.
Call our Aerial Helpline on 0800 5428265 for more information.
4
Five quick and easy steps to get you up and running
Step 1
Unpack your Digital TV Recorder (DTR) and check you have all the
following accessories:
• Remote Control
• SCART lead
• Aerial lead
• Mains lead
• Remote control TV set-up codes
•2x AA batteries to place in your remote control
IMP RTANT: Disconnect the power to all your existing equipment.
Now place your DTR where you want to keep it and connect it to your TV as
shown in the diagram, by following these simpe instructions:
ADBC
Step 2
Quick Start Guide

6
AUnplug the aerial cable from your VCR (or TV) and plug it into the Aerial In
socket of your DTR.
BUsing the aerial lead supplied, connect the RF Out socket on your DTR to the
Aerial In socket of your VCR (or TV).
CUsing the scart lead supplied, connect the TV SCART socket on your DTR to
the AV1/EXT1/AUX1scart socket at the back of your TV.
DAnd lastly, connect the mains lead to the Mains Input socket on your DTR
and switch on at the mains. Reconnect the power to all your existing
equipment and Turn your TV on.
When you plug your box into the power supply or when it is updating, a red-
amber light will be displayed for about 45 seconds. You must wait for it to
change to solid red or green before pressing any buttons.
Step 3
You now need to scan your box for all the available channels and install your
14 day TV listings guide.
Press the DTR button on your remote. The button will momentarily flash. This will
confirm that the remote control is working correctly. Now wait for the light on
the front of your DTR to turn from amber to green.
Your TV should now automatically switch
to external output and display the image
shown. If this does not happen, select the
external TV input to which the DTR is
connected. Refer to your TV Handbook for
details but it’s likely the button will be
labelled AV/AUX/E or similar.
7
Once you can see the image on screen displayed here, and have ensured all
connections are correct, press on your remote.
You will now see this screen
showing that your DTR is now
searching for all available channels.
In the event that your DTR does not
find any channels, or has missed
some, see the section on What to do
if your Installation fails.
When your DTR has successfully found all channels, your DTR will search for and
install your 14 day TV listings guide.
Step 4
You will now be prompted to set up the Parental Control for your DTR as it
enables you to receive programmes from Top Up TV Anytime throughout the day
using a viewing card, in addition to the standard Freeview channels.
If children have access to your DTR, it is advisable to select the appropriate
viewing certification now, in order to restrict access. E.g. By selecting 12A, you
will receive programmes to this certification and not those of 15 or higher.
Once you have completed this step, press on your remote.
Quick Start Guide

8
Step 5
If you have a Top Up TV Viewing Card giving you access to programmes from
channels including UKTV old, Discovery, LIVIN , Paramount Comedy and more,
you should insert it when you see this screen.
To insert the viewing card, simply pull
down the panel on the front of the DTR
and insert the card into the viewing card
slot following the direction of the arrow
and with the gold chip facing down.
Ensure the card is fully inserted. You will
see the screen shown below if the card is
not properly inserted.
Now turn to Channel 5straight away and
leave your box tuned to this channel for
around 30 minutes. Some customers will
need to call us to activate their service so
you should refer to your card instructions
for details.
It will take up to 48 hours for your first Top Up TV Anytime programmes to
appear on your DTR, but you will be able to watch your Freeview channels as
normal.
Please ensure you ALWAYS leave your DTR N or in STANDBY to make sure you
receive all the programmes Top Up TV sends you on a daily basis. It will take 7
days for your DTR to fill up to its full capacity.
9
If you do not currently have a Top Up TV viewing card but would like to watch
programmes from channels such as those mentioned above, call Top Up TV on
08444 158 158. Otherwise, press on your remote and you should now
be able to start watching any of the available Freeview channels.
What to do if your installation fails
• Check that all the connections have been made as shown in the diagram
and the power is switched on to all of the equipment.
• Check that the batteries in the remote control are in the right way round
and press the DTR button. Check that the DTR button flashes when pressed.
• Make sure the TV aerial is connected directly to your DTR (1st in chain).
• Check any signal boosters are Digital TV compatible and switched on.
• Repeat the installation by following the tuning instructions on page 27 of
the main user manual.
• If this does not help, you may need an aerial upgrade. For more information,
contact our approved Aerial Installation Helpline on 0800 5428265.
Quick Start Guide

11
Safety Information
10
●Place the recorder on a flat and hard surface. Do not place any objects (e.g.
newspapers) on or under the recorder.
●If placed in an enclosed unit, the all-round distance between the recorder and the
sides of the unit must be at least 10cm. Do not allow the vent slots in the sides or
underneath to become obstructed.
●Do not place the recorder in the immediate vicinity of a heat source or in direct
sunlight as this would prevent appropriate cooling.
●During a thunderstorm it is recommended that you disconnect the recorder from the
mains and aerial to prevent damage from lightning strikes.
●Never open the recorder as this will invalidate your guarantee.
This symbol on your set guarantees your product complies with European
Directives 2006/95/EC, 89/336/EEC on safety and Electromagnetic compatibility.
Environmental Information
The batteries use some hazardous substances which are very polluting for the
environment. Do not throw them out. Remember to dump them in collection points.
CLEANING - Dust will collect on the unit and can be removed with dry clean cloth.
Do not spray any substances directly on to the unit.
In order that you may enjoy this product for a long time it is important that you observe
the following points when installing and operating your recorder.
Note: In order to disconnect this equipment completely from the mains it is necessary to
withdraw the plug from the wall socket. Please ensure that the plug remains accessible
at all times. As soon as the mains plug is inserted into the wall socket it will become
powered and commence its initialisation sequence. When complete the unit will remain in
its standby mode until activated by use of either the remote control or front panel stand-
by button .
●Disconnect the recorder from the mains supply before you connect the recorder to
(or disconnect it from) any other equipment. Remember that contact with 230 Volt AC
mains can be lethal or cause severe electric shock.
●This recorder is intended for the reception of TV picture and sound signals. Any other
application is expressly prohibited.
●Do not expose the recorder to any moisture. The recorder is intended for use in dry
rooms. If you wish to operate it in the open air, make absolutely sure that it is
protected against moisture (rain, splashes, etc.).
●Do not place any object filled with water (vases or similar) on the recorder.

The OFF button on the remote control and on the recorder itself, does not completely
disconnect the unit from the mains supply, but switches operating power on and off.
Accessories
Aerial lead Scart lead
Remote
Control
User Manual
Quick uide
Mains Lead
2x AA
Batteries
Remote control
TV set-up codes
Safety Information



Remote Control
Using your DTR Remote to control your TV
The DTR remote control is capable of controlling the common functions of your TV. Locate the
“Remote control TV set-up codes ” sheet from your accessories and find your make of TV on the
list. Note the four digit number(s) applicable to your TV. On the DTR remote Press TV,
, now press
and hold K and AV together. The TV button will flash twice. Now enter the 4digit code relating
to your make of TV. Again the TV button will flash twice. If an invalid code is entered, the TV button
will only flash one long flash.
Make sure that the entered code is the right one for your TV by
pressing the ‘active’ buttons from the list below. If your TV does not
respond, repeat the sequence with the next available code in the
table. Once you are sure that the code is correct you can write it
down in the box to the right and on an identical label on the inside
battery door of your DTR remote control.
Controlling your TV set
TV Sets the remote control unit in TV mode (by pressing once)
and enables you then to control your TV set.
Switches the TV set on or off
Vol. +/- TV Volume control.
Switches sound off or on again.
CH +/- Switches channel or selects an AV socket.
AV Selects an AV socket.
0 to 9 Change channel or enters digital values.
TEXT Access Teletext pages (On /Off).
‘Play’ button Access Teletext pages (Off)
Colour buttons Enables you to use the Teletext function on TV sets.
Insert the batteries into the handset as shown. Point the remote
control at the DTR and press the DTR button. The DTR button will
flash once to confirm that the remote control is working correctly.
Important information regarding the batteries
Do not mix different types of batteries or new and old batteries. Do
not use re-chargeable batteries. Do not throw batteries into a fire,
do not recharge them. Remove the batteries from the remote control
if you are not going to use it for several weeks. Immediately remove
any leaking batteries. Take care in doing this, as leaking batteries may cause burns to the skin or
other physical injury.
Inserting the batteries
Please respect the environment and prevailing regulations.
Before you dispose of batteries ask your dealer whether they
are subject to special recycling and if they accept them back.


12 13


Introduction
Congratulations on your choice of this state-of-the-art Digital Television Recorder (DTR). We hope
you will enjoy all the new features this technology brings to your home for many years. Your DTR
is going to revolutionise the way you watch TV.
You can pause live TV, for example while you answer the phone and then resume watching where
you left off. You can also record two different channels at the same time. Delayed viewing, fast-
forward and rewind functions allow you to play and replay the sports action without having to
worry about the rest of the game which is still being recorded. These features could make you lose
track of time, but fortunately the LIVE TV button brings you back to the present instantly.
Your dealer should have checked your postcode for reception, but the availability of Digital Signals
does depend on the transmitter(s) available to your receiving aerial. If you have any doubt about
this availability, please contact your dealer, or try one of the following:
• Text your postcode to 83331 (standard rates apply)
• Visit the websites www.freeview.co.uk or www.dtg.org.uk/consumer
• Call FREEVIEW on 08708 809980
If you experience reception problems, check page 35 for some suggestions
or contact our aerial helpline on 0800 5428265
N TE : This product can be upgraded from software updates broadcast over the air to your
recorder. The manufacturer reserves the right to transmit software updates that it would consider
appropriate in order to improve the functionality of the product, without degrading the quality
level.
Getting started

15
14
Advanced Connections
If your TV or VCR has an S-video connector, you can connect
your recorder to it with a suitable S-Video cable.
You can also connect your recorder to an external audio
amplifier with suitable cables. You can choose between analogue
audio or digital audio outputs.
More/Advanced Connections
The diagram on page 14 shows a connection method that includes a VCR. The supplied Accessory
cables allow rapid connections to the TV only, in order to get you going as quickly and easily as
possible. But should you wish to adopt the more advanced connections shown in the diagrams,
please purchase additional leads as explained below.
Archiving off the DTR onto a VCR or other recorder
Use a scart lead to link the VCR SCART socket on your DTR to the
AV1/EXT1/AUX1socket of your VCR. This connection will allow you to
archive to a permanent media. If your VCR supports auto-start recording,
then the DTR will control the VCR automatically.
Connection to a Hi-Fi system
Use a pair of stereo coaxial phono leads to connect the L/R AUDI UT
socket on your DTR to the L/R AUDI IN on your Hi-Fi unit. This will allow
you to hear higher quality sound through your Hi-Fi.
N TE : Audio sockets are generally identified by colour. White for Left and Red for Right.
Coaxial connection to an Audio Visual Amplifier
To get even better sound from your DTR, use a digital audio phono lead to
connect from the DIGITAL AUDI UT socket on your DTR to the DIGITAL
AUDI IN on your AV amplifier.
S-Video connection to a TV, Plasma Display or Projector
The scart connection to a TV provides the best picture as R B
(Red, reen,Blue separately), but some types of display device don’t have a
scart socket. In this case, either an adaptor should be purchased, or connect
an S-Video lead from the S-VIDE UT on your DTR to the
S-VIDE IN on your TV, Plasma display or projector. This will also give a
high quality picture, but you must make a separate audio connection, as the
cable doesn’t carry sound.
How to connect the aerial and scart cables
REMEMBER SAFETY FIRST - ALWAYS UNPLU ALL YOUR EQUIPMENT FROM THE MAINS BEFORE
MAKIN CONNECTIONS
Connections
Follow the steps below referring to the numbered parts on page 7 and the diagram above:-
AUnplug the antenna cable from your VCR (or TV) and plug it into the Aerial In socket of your
DTR.
BUsing the aerial cable supplied, link the RF ut socket on your DTR to the Aerial In socket of
your VCR. Your DTR should now be linked first to your aerial, then to your VCR and finally the
VCR to the TV.
CUsing the scart lead supplied, link the TV SCART socket on your DTR to the AV1/EXT1/AUX1
socket of your TV.
DFinally, connect the mains lead to the Mains Input socket on your DTR and turn on your TV.
If you have a Top Up TV viewing card, please make sure it is inserted correctly now.
After a few seconds, the lights on the front will come on and a menu
will appear on the TV screen. Please follow the on screen instructions
carefully or refer to the Quick-Start uide.


BC DA
Getting started

To change the view to show what’s on NOW or NEXT, use the up /
down arrows.
To see what’s on another channel use the left or right arrows.
If you see a programme you want to watch, press K.
Using the Quick TV Guide
When you are watching TV you can find out what’s on other channels without interrupting your
viewing using the Quick TV uide. This is the small banner that appears at the bottom of the screen
during channel changes or when you press an arrow button.

N TE: The full Programme uide will normally be updated by your DTR automatically overnight.
Until then, you will have use of a reduced guide that will not enable you to access all the features
of your DTR. Please ensure you leave your DTR in Standby overnight, every night. Depending on
what time of day you set up your DTR, it may take up to 48 hours for Top Up TV Anytime
programme downloads to be recorded and placed in your library.
Shows the
current date
and time
Next Shows the
programme
name and start
time
Shows short
details of the
programme
(synopsis)
Now Shows the
programme
name and start
time
Shows the
channel name
16
Basic peration
Note : Before you go any further, are you watching a digital TV picture?
If not, check that your TV aerial is plugged into the DTR Aerial In and follow the on screen
instructions carefully or refer to the Quick-Start uide. This will make the DTR try tuning again. If
it fails again, you will probably need to upgrade your aerial, please refer to the troubleshooting
section on page 35.


To turn on your DTR, press any number button, the DTR button or
the button. The red standby indicator light will go green.
To turn off your DTR, press the button. The standby light will turn
red again. An amber light indicates the box is updating and that you
should wait before pressing any further buttons.
The DTR must be on or left in standby if you want to keep the
Programme Guide and Top Up TV programmes updated.
Turning n and ff
Changing channels
To change channel press the CH+ or CH- buttons. This will move
through the channel list one at a time. You can also set a favourite
channel list which will allow you to skip between the channels you
watch most often. How to set up this list is explained on page 33.
Note that the channel numbers are not continuous. These are set by
the broadcaster and cannot be changed.
If you wish to search for your channel by name, use Quickfind.
Press the K button.
Use the arrow buttons to move the highlighter around the
programme names, until the channel you wish to watch is
highlighted. (Only some channels are shown inside the box, keep
moving left or right to find the rest.) If favourite channels are
set, only those chosen will appear in the box.
Press the K button again to change the channel.
If you know the channel number you are looking for, enter this using
the number buttons. With digital TV there can be up to 3digits in the
number.
A banner with information about the programme currently showing
will appear briefly each time the channel changes. For more details
on getting programme information, see page 17
Teletext and interactive services
If your chosen channel has digital text features press the TEXT or coloured buttons to access them.
To return to normal viewing press TEXT again. Some services offer interactive features, details of
these and how to use them will appear on screen as they occur.
Using Your DTR
17

Using Your DTR
Using the Programme Guide
Your DTR has access to two programme guides. Initially your DTR will access
the broadcast 7day Programme uide, but as soon as your DTR has acquired
the Top Up TV on-screen programming guide, you will have access to 14 day
listings. The Programme guide screen gives you a fast way of planning your
viewing and recording. To access this guide, press the GUIDE button.
While in the Programme uide, you can navigate around using the arrow buttons. Up/down arrows
will move between channels, while the left and right arrows move in time. The uide is split into
three sections of 30 minutes each. The information contained in a time segment usually shows the
name of the programme. This is only the case when the programme takes up the whole of that 30
minute time slot. As programmes can be longer or shorter than 30 minutes, the Programme uide
has been constructed to inform you of this.
If a programme is longer than 30 mins the next time slot shows three dots to indicate that the
programme runs in to the next slot. If a programme is shorter that 30 mins the programme name
is followed by an arrow to indicate that more than one programme exists in that slot.
If a programme does not start exactly on the time boundary, it will have two dots in front of the
programme name to indicate that it starts later than the time shown in the column heading.
If you leave the highlighter box over a
programme for more than five seconds, a box
will appear showing a synopsis of the
programme. It also shows the start and end
times for that programme in the top right-hand
corner.
To set up and work the other facilities of your DTR you will need to
get used to operating the menus. Throughout this manual, we will
use B LD text when referring to remote control button presses, and
ITALIC text when referring to a particular menu level.
You will be using the remote control buttons highlighted and the
coloured buttons, take a moment to find them now.
Please refer to the inside front cover for a full colour image of your
remote control and its primary functions.
To use these menus, you must first press the MENU
button which will then display the main menu.
Now choose the item (called a sub menu) that you
want to look at.
You do this by using the UP arrow (), to move
the yellow box up the list and the D WN arrow
() to move it down the list.
Once you have highlighted your choice with the yellow box, press the K button to move to the
new menu level.
If the DTR states that a PIN number is required (Personal
Identification Number), enter this now.
The default number is 0000 you can find how to change this on
page 32.
As you learn to use the DTR you will find that the number buttons
can take you directly to sub menus without the need for using the
arrow buttons. e.g. Use 4for the fourth item (setup), 1for the first
item (Programme Guide), etc.
In each menu, look at the bottom lines of text for more information
on which buttons to press. This could be arrow buttons (or )
or the coloured buttons.
Finally, when you have finished making adjustments, use the BACK
button to return to the TV picture. You may need to press it more
than once, depending on the menu item.


Using the Menus


18 19

Using Your DTR
Across the bottom of the screen are a number functions activated by pressing the coloured buttons
on your remote control.
Go to day
Pressing the GREEN button will bring up an overlay
box (pop-up). This is the G T DAY menu.
Using the up and down arrows you will move the
highlighter to a day in the future. Pressing K will
take you back to the Programme uide, but now the
guide is showing programmes on the day you
selected. From here you can set-up recordings or
reminders.
Favourites
Pressing the BLUE button will present the guide with
just your selected favourite channels displayed.
If you have not yet created a Favourites list, you will
see a pop-up as shown. Pressing the RED button will
close the pop-up. Pressing the REEN button will
take you to the Favourites set-up screen.
Use the Up and Down arrows to highlight a channel that you
would like to make a favourite. Press K to add it to your
Favourites. Your Favourites are identified by a . You can
remove it from your list by pressing the OK button again. Also
use the RED button to select all, or the REEN button to delete
all.
To exit this menu press the BACK button.
Set reminder
Pressing the YELL W button will add a reminder to the currently highlighted programme. you can
see if you have set a reminder as the reminder icon will appear next to the programme name.
If you wish to cancel the reminder, press the YELLOW button again.
When that event arrives, you will be reminded by a pop-up which
will appear on-screen.
You can accept the reminder by pressing the GREEN button to
watch the programme or cancel it with the RED button.
Record
Pressing the RED button will take you to the PLANNED
REC RDINGS screen. Press the RED button again to
add the recording to the ‘planned recordings list.
When you go back to the TV uide, you will see
next to the planned recording.
For more information on planned recordings, please
refer to ‘Using Planned Recordings’ on page 24.
Top Up TV Anytime
In addition to the standard Freeview channels, your DTR
can also give you access to a wider range of programmes
on Top Up TV Anytime.
By subscribing to Top Up TV Anytime for a small monthly
fee, your DTR will automatically record and download
programmes from channels such as Discovery, UKTV
old, Paramount Comedy, MTV, LIVIN and more, for
you to watch whenever it suits you.
The channels from which you can choose to select programmes are shown across the
bottom of the Programme uide screen.
Pressing the Top Up TV button on your remote enables
you to view the list of programmes available to watch
right now. Then you simply use the left and right arrow
buttons to scroll through and press OK on anything
you want to watch.
To view programmes from these channels call now on
08444 158 158.
20 21

Using Your DTR
Using your Programme Library
To access the PR GRAMME LIBRARY press the
LIBRARY button on your remote control or option 2
from the MAIN MENU.
Initially the Programme Library will be empty, but as
you start using your DTR, it will build and show not
just the recordings that you have made or saved, but
also the Top Up TV Anytime programmes that are
stored on your DTR and available to watch at
‘anytime’.
Your DTR storage area is partitioned into two sections.
For more information on how to change the partition
sizes, please turn to page 30. The two sections are
arranged so that you have control over the ‘top’
section which appears first on the top section of the
menu. Here you can keep your recordings or delete
them to make more space as required. To delete a
recording, move the highlighter with the UP or Down
arrow buttons over the programme that you wish to
delete and press the BLUE button.
When you move the highlighter into the Top Up TV Anytime storage area, you will notice that the
screen appears slightly different. There are two differences, the first and most important is the Da s
Left column, the second is the red Save button.
Days Left
This shows how many days the programme will
remain stored on your DTR before it is automatically
deleted and replaced with new programmes. You may
watch the programme at anytime, but if the Da s Left
number reaches zero, you only have a few hours left
before the programme is over written. If you would
like to watch the programme, but do not have time
within the time remaining, you can move the
programme to ‘your’ storage area by pressing the
RED button. The programme will now appear in the top section of the Programme Library and the
Da s Left will show Saved.
There are a number of functions that are common to both storage areas: If you pause the
highlighter over a programme, that programme will automatically start playing in the small preview
window on the right-hand side of the screen. If you wish to watch the programme, press the K
button. If you had previously not finished watching a programme, press the GREEN button to
resume the playback from the last watched point.

You can always access the Top Up TV programmes by pressing the Top Up TV button.
Folders
Programmes on your recorder are automatically
placed in folders. Each recording can reside in more
than one folder, the ALL category and typically one
other genre folder, for example, Movies, Sport, Kids
etc.
To move between Folders use the LEFT and RIGHT
arrow buttons. To Highlight a programme use the Up
and Down buttons. To view the programme, press the
K button.
Synopsis
With the highlighter over a programme / recording, pressing the YELL W button will pop-up a small
window with a brief summary of the contents of that given programme.
Delete
With the highlighter over a programme, press the BLUE button. You will see a confirmation pop-
up to confirm that you wish to delete the programme or exit without deleting.
IC NS
There are two icons used to assist you in managing your Programme Library.
The at the end of the programme name field is used to indicate that a programme has been
watched.
The at the end of the programme name field is used to indicate that a programme is currently
‘playing’.
Pop-ups
Finally, you need to be aware of a few pop-ups that may appear to help you with your selections.
Depending upon the way you have set-up your recorder, or if you
have not set-up enough storage space on your DTR or you have
simply run out of space, your DTR will prompt you that there is not
enough space to store your selection. If this happens, you will need
to delete some of your recordings if you wish to save additional
programmes.
Also, a similar pop-up may appear if you are saving a programme
that will limit the storage space for any future recording. In this
instance you may save this programme, but you should also go to
the Planned Recordings menu to make sure you have enough space
and if necessary delete old recordings.
22 23

Using Your DTR
Using Planned Recordings
Your DTR is very versatile and will allow you to customise the way your record a programme.
In this section, we will show you just what options
are available to you. Typically you will have pressed
the RED button in the Programme Guide which will
have automatically taken you to this screen, but you
may also wish to set an recording manually. If you
have arrived at this screen via the Programme uide,
simply press the RED button to accept the default
settings and your recording will be added to the list
and completed without further interaction.
If you wish to set-up a manual recording via the
Planned Recordings menu, you will typically be
presented with a virtually blank screen as shown.
Press the GREEN button to continue and you will be
prompted to enter the channel, date, start and stop
times. Use the LEFT and RIGHT buttons to increment
or decrement the selection and use the UP and
D WN buttons to move between the settings. Finally
press the GREEN button to add the event to your Planned Recordings list.
Editing an event
There may be an occasion where you wish to adjust the recording (event) that you are setting.
This DTR allows you to change both the start time (TIME) and the duration of a recording.
Entering a recording from the Programme Guide or manually from the Planned Recordings menu,
the highlighter will be positioned over the PROGRAMME field. Press the RIGHT arrow button to
move the highlighter over the TIME field. Use the GREEN or YELL W buttons to increase or
decrease the start time. You can also move the Highlighter to the DURATION field again with the
RIGHT arrow and use the GREEN or YELL W buttons to increase or decrease the recording duration.
Once satisfied with your adjustments, press the RED button to add this recording to the list.
Why edit an event?
There may be occasions where multiple recordings overlap and your DTR will warn you that two
recordings collide. You may know that the programme you wish to record has moved due to an
over-run of a previous programme. Or simply, you know that the part of the programme you are
interested in starts later that the actual programme start time; for example, a football match. Editing
the timing will allow you to record programmes that would otherwise conflict with each other and
save space on your DTR for future recordings.
Your DTR is also capable of automatically adding time to a recording to guard against programme
over-run. Please refer to Page 31 for more information on Guard Times.


Space for recordings
When you add a recording to the Planned Recordings, your DTR will
check to see if there is enough space to complete all the scheduled
recordings. If there is a risk that there is not enough space, you will
see this pop-up. You have the option to cancel the recording or
continue with the event. If you continue with the recording, you
should go to the Programme Library menu and try to clear space by
deleting programmes that you have already watched and no longer wish to keep. If you do not
make space, you may lose the end of your recording or fail to be able to record further
programmes.
Simultaneous recordings
Your DTR has two tuners which means that it is capable of recording
two different programmes at the same time. In the event that you try
to record more than two programmes at the same time, your DTR will
alert you to this overlap with the pop-up shown. The pop-up will
inform you of the date, time and duration of the overlap.
Make a note of this overlap and go back to the Planned Recordings main menu. Find the
programmes that overlap and look to see if you can manually change the start times or durations
of the overlapping events to resolve the conflict. This will still enable you to record the
programmes you wish and not miss anything of significance.
Series Link
Some programmes are broadcast with special tags that indicate that
the programme is part of a series. If while setting a recording your
DTR detects this tag, it will advise you with this pop-up. You now
have three options; cancel the recording (RED button), record all
programmes with that ‘Series link tag’ (GREEN button) or just that
specific programme and remove the Series link (YELL W) button. When you go back to the
Programme Guide, you will see that a series link icon has been added to the programme name. It
looks like this
Top Up TV Anytime services conflict
At certain times of the day (or night) your DTR will attempt to use both tuners to record the Top
Up TV Anytime services. If the recording that you are setting up conflicts with a Top Up TV Anytime
service event, your DTR will warn you of this conflict and present
you with a list of the Top Up TV Anytime programmes that won’t
record as a result. You then have the option to cancel your recording
and allow the Top Up TV Anytime download, or continue with your
recording and not the Top Up TV Anytime one.


24 25

Recorder Functions
Numeric channel entry
Channels are ordered in a preset list this is called the Logical Channel
Number (LCN). Once you have been using your recorder for a little
while you will remember the LCN associated with a particular channel.
You can enter the LCN directly with the numeric buttons on your remote
control. You will need to enter all three digits of the LCN.
Stream swap
Your DTR has two tuners which means it can receive two different channels at the same time.
You can switch between these two channels by pressing 0on your remote control. If that channel
is paused, it will automatically switch to play to allow you to watch the programme. Furthermore,
if you are watching a recorded programme, your DTR will pause that programme and switch to the
programme currently being received by one of the tuners. Pressing 0again will switch to the other
tuner and pressing 0again will return you to your recorded programme and resume playback.
Instant record
If while watching a programme you decide you wish to record it, press the REC RD button on your
remote control and hold for 3seconds. Y our DTR will automatically record the programme to the
end of the scheduled time and add any of that programme that exists in your review buffer.
Chase play viewing
This is the ability to view a programme that is currently being recorded as part of a scheduled
record or an instant record process. There are two ways to view a programme while it is being
recorded. From Planned Recordings highlight the programme you wish to watch and press the RED
button on your remote control and hold for 3seconds. This will start the programme from the
beginning. You can also change channels to the one that is recording your programme and use trick
modes such as REWIND to move back through the recording to your desired point.
Trick modes
These are functions that enable you to move forward or rewind
through a recording. There a nine incremental speeds for both
forward and rewind, these are ⁄, fi, x1, x2, x4, x8, x16, x32 & x64.
Press the forward or rewind button on your remote control to enter
the trick mode. Repeated presses of that button will increase the
speed. To reduce the speed press the opposite button.
Note: That quarter and half speed modes are only accessed from pause mode. To enter pause
mode, press the Pause button on your remote control. Also, while in pause mode, you can press
the pause button again to advance one frame. Continued pressing will advance frame by frame.


Set-Up
From the MAIN MENU, press 4or select Set-Up. The basic set-up menu has 6options, but the
ability to be expanded with additional options. Press the RED button to expand the menu to see
all of the set-up options. The set-up menu should now look like this:
Use the UP and D WN buttons to highlight the sub-menu you wish to enter and press the K
button, or press the number button that is associated with the sub-menu.
SCAN For Channels
You will have performed this option automatically as
part of the installation process, but if for any reason
you wish to re-scan for new channels (if you have
moved or have a new aerial for example), make sure
that all the connections to your DTR are connected
correctly. Press the GREEN button to start the
automatic search for available channels.
Once the scan has started you can cancel it by pressing the RED button.
You can monitor the progress of the search as your DTR first searches for digital broadcast
frequencies and then for specific programmes on those frequencies. Finally your DTR will attempt
to acquire the Top Up TV Anytime service.
When the scan is complete, the text at the bottom of the screen will say Scan complete and the
GREEN button will re-appear to enable you to re-scan if required. To exit this menu option, press
the BACK button.


26 27
Setting Up

Throughout the set-up menus, we will list the available settings within an option. Please note that
the DTR factory default will be UNDERLINED. If at anytime your are not sure what setting to make,
refer to the relevant page and look for the setting that is underlined.
Customise DTR
Use the UP and D WN arrow buttons to select
an option and use the LEFT and RIGHT arrow
buttons to cycle around the available settings.
TV Picture format
Use the LEFT and RIGHT arrow buttons to
choose from 4:3 letterbox (black bars top and
bottom), 4:3 Centre Cut- ut (full screen, but
lost picture on left and right), 4:3 Full Screen (if
your 4:3 TV supports 16:9 switching, check your
TV manual) or 16:9 Widescreen (for widescreen TV's).
TV Picture Adjust horizontal and TV Picture Adjust vertical
Select these options to move the picture generated by the DTR either horizontally or vertically
so it sits centrally on your television screen.
SCART setting
Use the LEFT and RIGHT arrow buttons, to choose from S-Video (for specific TV’s), RGB (for
best pictures) or PAL for all other types. See your TV manual for the best choice, it usually
depends on which socket you connect to.
Programme search
This option turns on or off the "Search" facility (accessed using the red key in the uide) that
provides a search facility across the EP and VOD listings. When enabled the red key is used to
access the Search screen and the white (R) key is used to record programmes within the uide.
If disabled the red key is also used to record programmes within the guide.
Synopsis Pop Up delay
This option allows you to either turn off the synopsis window that pops-up over the uide or
video when a programme is selected, or to change the period that you wait for before it
appears.
RF modulator [advanced]
Your DTR is equipped with an RF (aerial) modulator. This feature allows you to watch pictures on
a TV set when only connected via the aerial lead. This can be useful if you wish to send the pictures
from your DTR to more than one TV in your house. Using the example method below, you can also
view the VCR on other TV's in your home. Check your VCR manual for details on its RF modulator.
Plasma blanking [advanced]
This option allows you to specify a time after which the display automatically dims. This is
important as static images can damage certain screen types.
For both Radio and Plasma blanking the available settings are: FF 3, 5, 10, 20 (mins)

It is strongly recommended that the main TV is connected using the scart lead provided as this will
provide the best possible pictures. These instructions assume you are connected to the main TV
with a scart lead as shown on page 5.
Make sure that all the aerial connections have been made as shown in the diagram below. You
will need an aerial distribution amplifier (splitter), this can be purchased at most good dealers
or DIY stores. Make sure you use good quality, double screened co-ax aerial cables. (e.g.
CT100)
Referring to your TV user manual, tune your TV's into channel 22 (default) for the DTR.
If this picture is snowy or disrupted, you may need to change the modulator channel.
Use the LEFT and RI HT arrows to change the modulator channel number (21 to 69).
Finally, re-tune the TV again.
Repeat step 3until you have clear pictures on all your TV sets.
If you do not wish to use the RF modulator then choose off.
Press BACK to return to TV viewing.


28 29
Setting Up

Customising Top Up TV Anytime
One of the great things about Top Up TV Anytime is
that you don’t have to download all the programmes
available. You can choose to record and download
only those programmes from channels you watch. So
for example, if you don’t have kids, you can save
space on your hard drive by de-selecting the kids
channels, giving you more space to download those
you do want to watch. Customising your channels is
easy and should be done on a regular basis to ensure you maximise the amount of space you have
available for your own recordings. This menu presents a list of available Top Up TV Anytime
channels. Use the LEFT and RIGHT arrow buttons to move between columns. Use the UP and D WN
arrows to move the highlighter over a channel for
activation. Press the RED button to activate the
channel.
Note the two times on the bottom of the screen. The
Top Up TV (TUTV) hours per week will change as you
activate or de-activate channels. The available space
left for personal recordings on your DTR’s hard disk
drive (storage space) is shown on the far right.
In some cases there will be insufficient free storage space in the Personal Disk Space area to re-
assign for Top Up TV Anytime use. In this case, a pop-up will be displayed as shown to enable
you to remove content from the Record Library. Use the UP and D WN arrows to select a
programme and then delete it by pressing the RED button. Once you have created enough space,
you can activate the new channel by pressing the GREEN button. To exit this menu press the
YELL W button.
You may attempt to activate a channel for which you do not have the right level of subscription.
If this occurs, you will be taken to the Subscription screen. Follow the steps on screen to change
your subscription.
Warnings
There are some warnings that may pop-up as a result of some of your selections / actions.
The first of these may be if you de-activate a Top Up TV Anytime channel. The warning will inform
you that if you de-activate this channel, you will no longer receive any of that channel’s
programmes and delete any recordings made from that channel.
The second warning you may see is in activating a new channel, you may not have enough space
on your disk drive for planned recordings. The warning will advise you to review your Planned
Recordings as soon as possible. Please refer to page 23 on how to make space by deleting
unwanted recordings.




Recording Preferences
There are two options available to change, the uard
time and the rewind buffer size. Use the UP and
DOWN arrow buttons to move between the two
options and the LEFT and RI HT arrows to scroll
through the available values for that option.
Recording guard time
A guard time is a small amount of time added to the
start and end of a recording to help protect against programmes starting slightly ahead of schedule
or more typically over-running their scheduled finishing time. There is obviously a small penalty
for this feature which is that you will use up more space for each recording with a guard time set.
The available settings are FF,1, 3 or 5minutes. As you can see the default setting is OFF to
maximise the available disk space for recordings.
Pause live TV
Your DTR automatically records and buffers the channel you are currently watching. The size of this
record buffer is set to 30 minutes. This means that you can pause and rewind the channel you are
watching back by 30 minutes, or by the amount of time you have set as the Pause live TV buffer
size. As with the guard times, this obviously takes up space on your Hard disk drive for recording
other programmes so if you do not use this feature you can turn it off to increase the available
space for recordings. The available settings are FF, 15, 30, 45 or 60 minutes.
If while watching a programme you decide to record it, your DTR will use as much of the buffer as
is available to add to your recording in an attempt to record the whole of the programme from the
start.
Messages
Occasionally, events may occur that your DTR stores for your information. For example, your DTR
is capable of having its software upgraded automatically using the same transmission media as the
programmes themselves. If you have any messages
waiting to be read, a light on the front of your DTR
will come on. Also, in the Main Menu screen top
right-hand corner, a small envelope icon will appear
as shown. To view any messages, select Messages
from the Main Menu or Set-Up menu. Once you have
read your messages, you may delete them by
pressing the RED button.


30 31
Setting Up

Help
This is a high level information screen that will tell you basic information about your DTR. If you
require further assistance please call the telephone number shown on-screen.
There is also an option to press the RED button for
tuning information. This screen shows the current
status of the two tuners, what channel number they
are currently set to and the Strength & Quality of the
signals being received. You can also change the
channel a given tuner is set to with the coloured
buttons; RED & GREEN for Tuner 1or YELL W & BLUE
for Tuner 2.
Changing the channels that the tuners are set to may result in you losing scheduled recordings.
Please use this screen with care or wait to be advised on how to use this screen by one of our
Customer Care Advisers.
Child Lock [Advanced]
This menu option enables you to set-up
Parental Control levels and to determine the
access you and your family have to content.
As soon as you select this option, you will be
prompted to enter your Personal Identification
Number (PIN). The default number for this is
0000.It is highly recommended that you
change this number as soon as possible. Once
you have entered a valid PIN you are given the
option to change the PIN by pressing the RED
button and following the simple steps on-
screen.
Max Certificate
This sets the maximum certificate value allowed on any viewed content (Live or Recorded). If at
anytime a user tries to view content with a certificate higher than the maximum certificate allowed,
the recorder will blank the screen, mute the audio and pop-up the PIN entry window.
Unless a valid PIN is entered, the content cannot be viewed. The available settings are; U, PG, 12,
15 or 18. Note that the default is 18 which means that there is no automatic block of any content
from being viewed. You should lower this to a level suitable for the people with access to your
DTR.
Note that setting a certificate does not limit the content that can be recorded, only what can be
viewed. This allows viewing decisions to be made when the viewer is present.




Lock Period Start & Lock Period End
This allows the DTR to be locked down during the START and END times. Use the LEFT and RI HT
arrow buttons to increment or decrement the time in 15 minute steps. In both cases, the default
value is FF.
Lock
Once you have set lock periods, you will have to activate them by setting Lock on. Likewise, you
can also turn lock periods off with this option.
Favourites [Advanced]
Setting Favourites, enables you to just scroll around the channels that you wish to see and not the
entire list of available channels. This does not preclude you from watching a channel outside of
your favourite list, simply enter the channel number directly or use the Programme uide.
To Set-up your FAV URITES, use the UP and D WN
arrows to highlight a channel that you would like to
make a favourite. Press K to add it to your
Favourites. Your Favourites are identified by a . You
can remove it from your list by pressing the K
button again. Also use the RED button to select all, or
the GREEN button to delete all. To exit this menu
press the BACK button.
Languages [Advanced]
Preferred audio language
This option sets the Preferred language audio output. In a multi-language broadcast, your DTR will
attempt to acquire your preferred language. If your preferred language is not available, your DTR
will switch to the default language.
Preferred subtitle language
This has the same action as Preferred language, but for Subtitles in place of the audio output itself.
To select an option, use the UP or D WN arrow
buttons. To scroll around the possible languages, use
the LEFT and RIGHT arrow buttons. The default
Language is English and the available options are
Welsh and Gaelic.
32 33
Setting Up

Troubleshooting
Tuner conflict resolution
In some cases there may not be enough tuners for all the
functions your recorder is trying to perform, for example
if two recordings are taking place and you try to change
channels, you will see this pop-up menu. If you really wish
to change channels, go to the Planned Recordings menu
and cancel the recording. Pressing the RED button will take
you to the Planned Recordings menu.
Top Up TV Anytime conflict resolution
Watching live TV may conflict with the requirement to record Top Up TV Anytime programmes. This
may occur if you are watching a programme when the Top Up TV Anytime programmes start, you
switch on your recorder while Top Up TV Anytime programmes are being recorded or you are
watching a Top Up TV Anytime programme but then try to change channels.
In the event of a conflict, you will see this pop-up. If you
press the RED button, you will continue to record the Top
Up TV Anytime programmes, however, if you press the
GREEN button the Top Up TV Anytime recordings will be
abandoned and your recorder will be considered to be in
override mode.
Your Recorder will remain in override mode for one hour or until it is placed in stand-by.
In the same way, if your recorder is trying to collect TV
listings or Top Up TV Anytime information, your recorder
will pop-up this warning. If you press the RED button, you
will continue to collect the required information, however,
if you press the GREEN button the task will be abandoned.
By overriding this task, your recorder may fail to update the TV listings and as a consequence,
may fail to record Top Up TV Anytime programmes.
Loss of Signal
If your recorder can not detect a signal, it will present this icon in the top centre of your
TV screen. Check all connections or refer to Reception problems on the following page.




Reception Problems
When you purchased your DTR, your dealer should have checked your postcode to ensure that you
can receive Digital TV. If you wish to check this yourself, please look on the internet websites:-
www.freeview.co.uk or www.dtg.org.uk/consumer.
Once you have established that your area should be able to receive digital TV, there are a few
reasons why you may be experiencing problems.
• Your current aerial and cabling may not be able to receive all the digital channels
due to its age and condition. Now is the time to renew them. We recommend the use
of CAI “Benchmarked” aerials. Look for the logo.
Always use good quality, double screened aerial cable. e.g. CT100 coaxial cable.
• In your location the digital channels may be transmitted on different frequencies to your
existing analogue signals and you may need a different type of aerial to receive them. Check
the ‘group’ of your aerial, you may need a ‘wideband’ one.
• The new digital channels may be transmitted from a new transmitter and if this is the case the
aerial would have to be re-aligned. Alternatively, add a second aerial to your system.
• If you need to use a mast-head amplifier, make sure that it is a digitally compatible one and
that it is as close to the aerial as possible.
• In some blocks of flats, filters may be in use that will interfere with digital signals. Consult with
your landlord if you have difficulties.
• Indoor or window mounted aerials are not recommended, except in areas where the signal is
extremely strong.
• Your aerial could be too high. Try adjusting the height of the aerial to avoid picking up
unwanted signals from other transmitters.
• If you live near a road, the passing traffic may cause problems. Try pointing the aerial at an
upward angle over the road, this helps reduce engine interference picked up by the aerial.
• If you get periodic picture losses, this could be due to electrical interference picked up in your
house. This could be from a central heating thermostat, a fridge/freezer, or any other item with
a motor. Try switching these appliances off temporarily to establish what is causing the
problem. Then replace the problem item.
• If your aerial comes into your room via an aerial connection point (socket), replace it with a
good quality shielded one. This will help prevent electrical noise entering your aerial.
If you are still having difficulties it’s likely that you may require an aerial upgrade. For help and
advice, contact our Aerial Helpline on 0800 5428265.
34 35
Information

Not every picture or sound problem is caused by a defect in your DTR. Leads having been
accidentally pulled out or worn out batteries in the remote control can also cause impairment. If
your unit does something unexpected while you are using it, please unplug it, wait a few seconds
then plug it in again. If this fails to solve the problem or the following measures do not bring about
satisfactory results, please consult an authorised dealer.
Recorder does not
respond to remote
control.
Press the DTR button on the handset.
Point the remote control at directly at the recorder.
Remove all obstacles in the path of the remote control signal.
Check or replace the remote control batteries.
Re-boot the DTR by briefly interrupting the mains power.
No Picture.
Disrupted Picture.
Check all connections at the rear of the unit.
Check the RF IN connection. Ensure cables to TV are inserted correctly.
Select AV channel on TV set.
Refer to reception problems on page 35.
No Sound. Check all connections at rear of unit.
No sound from VCR. VCR sound is not available at the Digital audio output socket. Connect
VCR to your amplifier directly.
No Power or
indicators not lit.
Check mains plug is inserted correctly and the power is switched on.
Check that the mains socket is operational. (Use a lamp to test it.)
Picture shape looks
wrong.
Set your DTR to match your type of TV. 4:3 = conventional
See page 28 for instructions. 16:9 = widescreen
DTR won’t record
any more.
The hard disk is full. Clear some space to allow the DTR to record.
An archiving event is occurring, wait for it to finish.
Live Pause won’t
work.
Two record events are happening at the same time. Wait for the
recordings to stop.
The hard disk is full. Clear some space to allow the DTR to record.
There is a humming
noise in the DTR.
This is the noise from the fan and the hard disk and is normal. It will not
generally be noticeable and is unavoidable.
DTR won’t change
channels.
Two record events are happening at once. Wait for the recordings to
stop.
Programme uide is
empty.
You must leave the DTR plugged in overnight to allow it to receive the
programme information. This takes place at about 3am every day.
No or less than 20
services tuned.
Insufficient signal is getting to the recorder.
Refer to reception Problems on page 35.
Subtitles not
appearing.
Not all programmes have subtitles. Check with your broadcaster for
details on subtitled programmes.
FAULT CAUSE/REMEDY
Technical Specifications
This product fulfils the European directives 2006/95/EC, 89/336/EEC. This device conforms
to the safety regulation EN 60065 and therefore the international safety regulation IEC 60065.
You may not open the DTR. The manufacturer accepts no liability for damage resulting from
improper handling.
Mains voltage: Power consumption: Standby Power consumption:
230V~, 50/60Hz Operating approx. 24W. 24W max
perating temperature: Audio Format: Remote Control battery Type:
+10°C to 35°C Analogue : Stereo Sound R6P SIZE AA 1.5V
Digital : SPDIF Stereo Sound
Hard disk: DTI6300-16/25 Dimensions: WxHxD - 368x62x221mm
Capacity: 160 B/250 B Weight: Approx. 1.8kg
Product Details
Front Panel indicators (LED’s)
Power status, reen On / Red Standby
Remote Command
Recording
Message Waiting
Rear panel connections
Front panel indicators and buttons
Front Panel buttons
MENU - Displays on screen menu
OK - Chooses highlighted option
Arrows - Moves the highlight around the screen
- On/Standby button
Tuner 2
output
to VCR
Tuner 2
Input
Digital audio
utput
PCM (stereo) only
VCR scart output
VCR pin 8record control RGB
loop through for DVD players &
Digital recorders
Analogue
audio output
Mains Input
Main Aerial
Connection
to Tuner 1
Tuner 1
utput
S-video
output
TV scart
output
RGB or CVBS
output
36 37
Information

Index
Adding
Favourite Channels . . . . . . . . . . . . . . . . . . . . . . . . .20
Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Audio Language
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Banner
programme information . . . . . . . . . . . . . . . . . . . . . .17
reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26,31
Changing
channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
your PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Channels
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
favourites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Child lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Days left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Digital audio output . . . . . . . . . . . . . . . . . . . . . . . . .14,34
Digital text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Disk space management . . . . . . . . . . . . . . . . . . . . . . . .25
Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Editing an event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Favourite Channels
choosing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Front panel indicators . . . . . . . . . . . . . . . . . . . . . . . . . .37
etting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
uard times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . .20,21,23,25,34
Indicators - front panel . . . . . . . . . . . . . . . . . . . . . . . . .37
Information
quick guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Programme uide . . . . . . . . . . . . . . . . . . . . .19,20,21
Inserting your Top Up TV Viewing card . . . . . . . . . . . . . .8
Instant Replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Interactive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Language
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Live Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12,31
Mains Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Optical digital audio output . . . . . . . . . . . . . . . . . . .14,35
Parental control
changing your pin . . . . . . . . . . . . . . . . . . . . . . . . .18
setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,32
Playback
Choosing programme . . . . . . . . . . . . . . . . . . . . . . . .22
Pop-ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,24,28
Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Programme
finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16,17,18
information . . . . . . . . . . . . . . . . . . . . . . . . . . . .17,18
Recording
currently-showing programmes . . . . . . . . . . . . . . . .26
future programmes using the Programme uide . . . .21
making space . . . . . . . . . . . . . . . . . . . . . . . .22,25,30
Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Remote control
replacing the batteries . . . . . . . . . . . . . . . . . . . . . . .13
operating your TV . . . . . . . . . . . . . . . . . . . . . . . . . .13
Removing
favourite channels . . . . . . . . . . . . . . . . . . . . . . . . . .33
viewing restrictions . . . . . . . . . . . . . . . . . . . . . . . . .30
Replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . .13
Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Series link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Setup
connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .14,15
basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
automatic tuning . . . . . . . . . . . . . . . . . . . . . . . . . . .26
languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
child lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
picture settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
favourite channels . . . . . . . . . . . . . . . . . . . . . . . . . .33
Scan for channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Synopsis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
System setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-33
Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Top Up TV Anytime . . . . . . . . . . . . . . . . . . . . . .7,8,21,30
Troubleshooting
eneral problems . . . . . . . . . . . . . . . . . . . . .34,35,36
Reception problems . . . . . . . . . . . . . . . . . . . . . . . . .35
TV uides
Quick uide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Programme uide . . . . . . . . . . . . . . . . . . . . . . . . . .19
Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Viewing restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Warnings
Fuse Rating - Your recorder is supplied with an approved 3AMP fused mains plug. When
replacing the fuse always use a 3 AMP (BS1362) approved type. To obtain a replacement
fuse contact your retailer. If the mains sockets in your home differ or are not suitable
for the type of plug supplied, then remove the fuse from the plug for safety, cut the
plug from the mains lead and refit a suitable type following Brown - Live, Blue - Neutral.
You must use a 13 AMP plug (BS1363) and fit a 3 AMP (BS1362) fuse. If any other type
of plug is used a 3 AMP (BS1362) fuse must be fitted, either in the plug, adaptor or the
distribution board.
Interference - Do not place your recorder near appliances which may cause
electromagnetic interference (e.g. hi-fi speakers). If you do, it may adversely affect the
working of the unit, causing the picture or sound to distort.
Covers - Do not remove any fixed covers as this may expose dangerous voltages.
Weather - It is advisable to unplug the aerial during a thunderstorm. Even if your
recorder and TV are switched off, they can still be damaged by lightning strikes.
Ventilation - The ventilation holes in the casing of your recorder prevent it from
overheating. Do not block or cover these holes - especially with cloth or paper. If your
recorder is to be built into a compartment or similarly enclosed, make sure that there is
a gap of at least 10cm on both sides and 20cm at the top and back of the unit.
Damage - Never use your recorder if it is damaged in any way. Always place your
recorder on a flat level surface avoiding anywhere which may be subject to strong
vibration.
Batteries - batteries are easily swallowed by young children. Do not allow young
children to play with the remote control unit.
Temperature - Avoid extremes of temperature, either hot or cold, place your recorder
well away from heat sources such as radiators or gas/electric fires. Do not place candles
or table lamps on or near your recorder.
Moisture - Do not allow your recorder to be exposed to rain, moisture or dust. Do not
place a plant or flowers which may need watering on your recorder. If any liquid is spilt
into your recorder it can cause serious damage. If you spill any liquid into your
recorder switch it off at the mains immediately and contact your store.
38