Thorn WeatherForce LED User manual

IP65
IP65
IP65 IP65
IP65 IP65
WeatherForce LED
Installation Instructions
Warning
Please read these instructions carefully before installation or lamp
replacement. Warranty of this product is subject to installation
and maintenance being carried using appropriate conventional
practices and/or any specic instructions enclosed within.
Installation must be carried out by a qualied electrician in
accordance with local wiring regulations. Ensure that the rated
voltage and frequency of the luminaire are compatible with the
electrical supply.
Disconnect mains power supply before installing, servicing or
maintaining the luminaire.
Changes to specication
The right is reserved to change the design and/or specication
without prior notice or public announcement.
Specication
This luminaire is designed to comply with
the requirements of AS/NZS 60598.
Supply Voltage: 240v ~ 50Hz
Classication For Protection: Against electric shock:
Class 1 earthed metalwork. This luminaire must be earthed.
IP Rating: 65 - A 6-10mm Ø, circular electrical supply
cable must be used to maintain the IP rating.
Maximum ambient operating temperature:
Up to Ta: 25�C
1. Remove the diffuser and gear tray
Product application
IP65
To install, remove diffuser, detach gear tray and maintenance suspension devices.
Installation positions and IP rating
This strong impact resistant product is made from Polycarbonate.
This material is ideal in waterproof & industrial applications.
However, it is not suitable for use in areas prone to contact with
solvents, detergents, oil, alkalis, organic chemicals, animal fats &
industrial cleaners.
Please contact your local Thorn ofce for suitable alternative
products to suit the above applications
Remove Screws
Suspended Mounting Direct Mounting
600mm Single
416mm 507mm
600mm Twin
1200mm Single
880mm 980mm
1200mm Twin

Green/Yellow Earth
Brown Active
Blue Neutral
1
2
3
SAP No: 96540006 Rev: A 1/2013
thn_weatherforce_0113
Thorn Lighting Pty Limited (ABN 74 060 142 501)
Head Ofce: 43 Newton Road, Wetherill Park NSW 2164
Ph. 1300 139 965 Fax. [phone] www.thornlighting.com.au
Attach the gear tray to the
base. Tighten screws rmly.
Fit the uorescent lamp (ordered
separately).
Attach the diffuser to the base.
Ensure the diffuser is locked in
place.
Mounting kits suitable for surface mounting, or suspension mounting
are available to order.
Order reference: Single - 96039252, Twin - 96039253.
5. Secure the gear tray to the base
8. Attach the diffuser
Mounting kits
Make the electrical connections at the terminal block.
4. Make the electrical connections
The WeatherForce can be mounted by direct screw xing through the
housing. It should only be drilled at the appropriate marked points where
the housing is suitably reinforced. Do not use oil.
Note: Fixing screws and washers are NOT supplied.
It is recommended drill bits specically designed for plastic are used.
Standard metal or timber twist drills may be used but if not properly
prepared for plastic they can instigate stress cracking which may spread
under load.
Do not overtighten any screws into or in contact with the plastic housing.
Permanent damage may occur even if not immediately obvious.
Recommended maximum torque 1.5Nm
It is recommended that installation is made using the end entry and gland
kit provided with the tting.
Warning: If the housing is pierced for back entry of cabling, do not run
mains cabling past ballast, Temperatures exceed 100°C.
Fit the electrical supply cable, conduit and cable gland to the entry point
on the base. Ensure the cable gland is tightened rmly.
Note: If not suitably sealed with
appropriate washers, glands
or proprietary sealing kits any
piercing of the housing will
interfere with the IP rating of
the product.
2. Mount the luminaire
3. Attach conduit, cable glands and electrical
supply cable to tting.
Mounting point
Mounting screws
Cable gland
Suspension mounting kit
Surface mounting kit
Screw
Washer