Thrane&Thrane SAILOR 6215 VHF DSC Radio User manual

What’s in the box?.....
What do I need to fit it?.....
How to install the VHF on desktop and overhead.....
How to install the VHF flush mount..... Drilling plan.......flush mount.....
INSTALLATION GUIDE
SAILOR 6215/6216 VHF DSC
Thrane & Thrane A/S •in[email protected]om •www.thrane.com
TT98-128470-THR-F
AA
BB
99-130248
Gasket
Flush Mount Bracket (2 pcs.)
Screw M4x45 TORX 20 (4 pcs.)
Connect to LOUD HAILER
(RED isolation on inner connector)
Connect to EXT. SPEAKER
(WHITE isolation on inner connector)
Connect to POWER +
(RED wire)
Connect to POWER -
(BLUE wire)
Square Nut M4x7x2.2 (4 pcs.)
Max wall thickness 26mm
99-130250
Remove material from shadedarea only!
89mm
177mm
R2.5mm x 4
Drilling plan.......on desktop and overhead.....
Cable assembly for waterproof installation..... How to install the handmicrophone cradle.....
99-130249
4 x M4 or hole for
self-tappingø3.9
150mm
53mm
71mm
196mm
23mm
9mm
Tilting ±20°
1.
2.
3.
4.
Connect the 4 cable connections with rubber vulcanizing tape as shown .....
Power Drill Jigsaw Screwdriver
TORX 20
Drill for M4 or
Ø3.9 self-tapping
NotNot
NotNot
Note!e!
e!e!
e!
- Firmly tie back and secure any wires not used in order to
avoid possibility for mutual shorting or shorting to ground!
- To ensure waterproof sealing:
If the surface isn’t plane and/or rigid remove the gasket and
seal with silicone sealant between the VHF and the surface.
U-Mounting
Bracket
Transceiver Gasket
Flush Mount
Bracket (2 pcs.)
Sun Screen
Fuse
6.3x3.2mm (10AT)
User & Installation
Manual
Handmicrophone
Cradle
Wheel Knob
(2 pcs.)
Screw M4x45
TORX 20 (5 pcs.)
Square Nut
M4x7x2.2 (5 pcs.)
Screw M4x12
TORX 20 (3 pcs.)
Screw ø3.9x19
TORX 20 (3 pcs.)
Screw M4x12
TORX 20 (5 pcs.)
Screw ø3.9x19
TORX 20 (5 pcs.)
USER& INSTALLATION MANUAL
SAILOR 6215 VHF DSC
Power CableConnection Cable,
1 m

Flush mount template
Remove material from shadedarea only!
89mm
177mm
R2.5mm x 4
Thrane & Thrane A/S •in[email protected]om •www.thrane.com
TT98-128470-THR-F
Scale 1:1
How to install the GPS..... input signal.....
Cutout template for flush mounting of the VHF…..
2 x M4 or hole for
self-tappingø3.9
34.6mm 46.8mm
28.5mm
Scale 1:1
Handset
Speaker Microphone
Control
SAILOR 6208
6215/16
(DSC Radio)
GPS in (NMEA 0183)
Cable
Service
Loud Hailer (4 ohm)
Speaker (8 ohm)
External
ACC. Port
Power
Handset Option
Control Speaker Microphone
Connection Box
SAILOR 6209
Accessory
SAILOR 6204/05
Speaker Microphone
Control
SAILOR 6204/05
Speaker Microphone
Control
SAILOR 6204/05
SAILOR 6201
SAILOR 6201
Connection Box
99-129890-A
VHF
Handmicrophone
SAILOR 6202
OR
12V DC
110/220V AC
GPS
GPS,
N163S
CALL
Hi/Lo
MENU
16/9
VOL
SQ
(HHstørrelse)
DISPLAY
Push=
Enter
CALL
Hi/Lo
MENU
16/9
VOL
SQ
(HHstørrelse)
DISPLAY
Push=
Enter
CALL
Hi/Lo
MENU
16/9
VOL
SQ
(HHstørrelse)
DISPLAY
Push=
Enter
Aerial
RX/TX
12V Battery
N420
24V DC
System Configuration..... Example.....
IMPIMP
IMPIMP
IMPOROR
OROR
ORTT
TT
TANAN
ANAN
ANT!T!
T!T!
T!
If this template was printed from an electronic
file or copied, scaling (1:1) may not be correct.
Consequently do not attempt to use a printed
or copied template without prior checking of
dimensions.
NotNot
NotNot
Note!e!
e!e!
e!
The SAILOR 6204/05 Control Speaker Microphone not yet available.
IMPIMP
IMPIMP
IMPOROR
OROR
ORTT
TT
TANAN
ANAN
ANT!T!
T!T!
T!
If this template was printed from an electronic
file or copied, scaling (1:1) may not be correct.
Consequently do not attempt to use a printed
or copied template without prior checking of
dimensions.
Mounting template for handmicrophone cradle.....
Brown,Pin 1,NMEA in +
Blue,Pin 2,NMEA in -
For waterproofinstallation use
rubber vulcanizingtape
GPS Cable (NMEA 0183)
99-130267
IMPIMP
IMPIMP
IMPOROR
OROR
ORTT
TT
TANAN
ANAN
ANT!T!
T!T!
T!
Please note that the unused wires do not short-circuit.
Cable Connections.....
Pin assignments
Front View
Wire color Pin
Brown 1
Blue 2
White 3
Green 4
Yellow 5
Grey 6
Pink 7
Red 8
1
2 9
8
7
6 10 3
4 5
Black 9
10 Orange - SCREEN (Drain)
NMEA in+
NMEA in-
NMEA out+
NMEA out-
Mike 2 /Line in
EAR 2 /Line ou
Hook_PTT
Bat_SW SupplyVolt when on
Internal GND =- Battery
Internal GND =- Battery
Description