Thrustmaster T3PM User manual

Europe, Middle East
ENGLISH
FRANÇAIS
DEUTSCH
NEDERLANDS
ITALIANO
ESPAÑOL
PORTUGUÊS
РУССКИЙ
ČESTINA
TÜRKÇE
POLSKI
SVENSKA
SUOMI
SLOVENCINA
MAGYAR NYELV
תירבע
ﺔﻴﺑﺮﻌﻟا
North America/
Norteamérica
ENGLISH
FRANÇAIS
ESPAÑOL
Latin America/
América Latina
ENGLISH
ESPAÑOL
PORTUGUÊS
Asia Pacic
日本語
繁體中文
한국어
ENGLISH

1/12

2/12
TECHNICAL FEATURES
1Pedal set
2Additional hard spring (black)
32.5 mm Allen key
4Spring retaining rod
5Upper retaining head with washer
6Elastomer cushioning ring (white – Shore 70)
7Upper plastic spacer (red)
8Soft spring (silver – installed by default)
9Lower plastic spacer (red)

3/12
WARNING
Before using this product, please read this manual carefully and save it for later reference.
For safety reasons, never use the pedal set with bare feet
or while wearing only socks on your feet.
THRUSTMASTER®DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF
INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.
Warning – Pedal set pinch hazard when playing
* Keep the pedal set out of children’s reach.
* During gameplay, never place your fingers on or anywhere near the sides of the pedals.
* During gameplay, never place your fingers on or anywhere near the pedal’s rear base.
* During gameplay, never place your fingers on or anywhere near the pedal’s front base.
NEVER
NEVER
NEVER

4/12
AUTOMATIC CALIBRATION OF THE PEDAL SET
IMPORTANT
- Never connect or disconnect the pedal set from the base of the wheel when the wheel is
connected to the console or PC, or during gaming sessions, to avoid calibration problems.
= Always connect the pedal set to the wheel before connecting the wheel to the console or PC.
- Once the racing wheel’s calibration is complete and the game has been started, the pedals are
automatically calibrated after a few presses.
- Never press the pedals during the racing wheel's self-calibration phase or while a game is loading!
This could result in improper calibration.
- If your racing wheel and/or pedal set do not function correctly, or if they seem to be improperly
calibrated: Power off your console or PC and completely disconnect the racing wheel. Then
reconnect all cables (including the power supply cable and the pedal set), and restart your console
or PC and your game.

5/12
ATTACHING THE PEDAL SET TO A SUPPORT OR COCKPIT
The pedal set can be attached to a variety of different compatible supports (sold separately) using
the five M6-type threaded holes located underneath the base. To do so, screw at least two M6
screws (not included) through the support shelf, and into the threaded holes on the underside of the
pedal set’s base.
Important: the length of the M6 screws must not exceed the thickness of your support by
more than 0.47 inches/12 mm, so as not to risk damaging the pedal set’s internal
components.
The pedal set’s setup diagrams for cockpits and other supports are available at
https://support.thrustmaster.com:click Racing Wheels / T3PM, and then Template - Cockpit
setup.

6/12
ADJUSTING THE PEDAL SET
Each of the three pedals includes:
- A pedal arm (10) with two perforations.
- A plastic head support (11) (placed between the head and the arm) with four perforations.
- A metal head (12) with multiple perforations (nine for the accelerator – six for the brake – six for
the clutch).
ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s
USB cable from the console or PC before making any adjustments to your pedal set.
Adjusting the HEIGHT of the gas pedal
- Using the included 2.5 mm Allen key (3), unscrew the two screws holding the metal head (12) and
its support (11) in place.
- Select your preferred height position, then replace and re-tighten the screws so that the metal
head (12) and its support (11) are held firmly in place.
Low position
High position (default)

7/12
Adjusting the SPACING of the three pedals
- Using the included 2.5 mm Allen key (3), unscrew the two screws holding the metal head (12) and
its support (11) in place.
- Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the
screws so that the metal head (12) and its support (11) are held firmly in place.
Examples illustrating the brake pedal:
Left position Centered position
(default)
Right position
Number of possible spacing positions per pedal:
- Three for gas pedal
- Three for brake pedal
- Three for clutch pedal
Adjusting the INCLINATION of the pedals
- Using the included 2.5 mm Allen key (3), unscrew the two screws holding the metal head (12) and
its support (11) in place.
- Turn the plastic head support (11)180°, then replace and re-tighten the screws so that the metal
head (12) and its support (11) are held firmly in place.
Examples illustrating the gas pedal:
Less inclined position (default) More inclined position
Number of possible inclination positions per pedal:
- Two for gas pedal
- Two for brake pedal
- Two for clutch pedal

8/12
INCLUDED SET OF BRAKE SPRINGS
4 possible configurations and settings for the brake pressure force
This mod lets you experience a different feel and resistance when braking.
You can choose to install it or not, according to your preferences.
Brake resistance Soft
Medium
(by default)
Hard Very hard
Recommended use Desk Desk
Pedal set
support
Cockpit
Soft silver spring (8)
x
x
White elastomer cushioning
ring (6)
x
x
Hard black spring (2)
x
x
1. Pull hard on the lower plastic spacer (9) to compress the spring and remove the spring retaining
rod (4) from its location.
Method 1:
Method 2:

9/12
2. Reposition the different elements on the spring retaining rod (4).
Start with the lower plastic spacer (9), your choice of spring (2) or (8), and then the upper plastic
spacer (7).
3. After your selected configuration, install the elastomer cushioning ring (6).
4. Adjust the upper retaining head with washer (5) and position it in its location.
5. Strongly compress the spring in order to place the spring retaining rod (4) in its location
A video showing how to change the spring is available at https://support.thrustmaster.com: click
Racing Wheels/ T3PM.