Thrustmaster T3PA-PRO User manual

- USER MANUAL
- MANUEL DE L’UTILISATEUR
- BENUTZERHANDBUCH
- HANDLEIDING
- MANUALE D’USO
- MANUAL DEL USUARIO
- MANUAL DO UTILIZADOR

РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
 ΕΓΧΕΙΡΙΙΟ ΧΡΗΣΗΣ
KULLANIM KILAVUZU
INSTRUKCJAOBSŁUGI

1/17
For: PC – PlayStation®3 – PlayStation®4 – Xbox One
User Manual

2/17
TECHNICAL FEATURES
12 lateral arches (left and right)
24 M8-type Allen screws
(to attach the lateral arches)
3 2 plastic washers
(to attach the lateral arches)
46 mm Allen key
(to attach the lateral arches)
5Removable CONICAL RUBBER BRAKE MOD
6Fastening and adjustment nut
(to attach the CONICAL RUBBER BRAKE
MOD)
7Backup
(various extra screws and nuts)
8 4 M3-type Allen screws
(to attach the removable metal stop)

3/17
11 Pedal set cable and connector
15 Removable foot rest
16 Lateral arches when installed
17 Removable pedal heads
18 Removable SPRING BRAKE MOD
(not installed by default)
19 Included 2 mm Allen key
20 Included 2.5 mm Allen key
17 Metal head
21 Plastic head support
22 Metal pedal arm
23 Removable metal stop
(not installed by default)

4/17
WARNING
Before using this product, be sure to read these instructions carefully and save them for future reference.
For safety reasons, never use the pedal set with bare feet or while wearing
only socks on your feet.
THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF
INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.
Warning – Pedal set pinching hazard during gaming sessions
* Keep the pedal set out of the reach of children.
* During gaming sessions, never place your fingers or thumbs on or near the sides of the pedals.
* During gaming sessions, never place your fingers or thumbs on or near the rear base of the pedals.
* During gaming sessions, never place your fingers or thumbs on or near the front base of the pedals.
NEVER
NEVER
NEVER

5/17
AUTOMATIC CALIBRATION OF PEDALS
IMPORTANT:
- Never connect or disconnect the pedal set from the base of the wheel when the wheel is
connected to the console or PC, or during gaming sessions, to avoid calibration problems.
= Always connect the pedal set to the wheel before connecting the wheel to the console or PC.
- Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate
themselves after being pressed a few times.
- Never press on the pedals when the wheel is self-calibrating or when your game is starting up, to
avoid calibration problems.
- If the pedals are not functioning correctly or appear to be improperly calibrated, power off your
console, completely disconnect your wheel, then reconnect all of the cables (including the power
supply cable and the pedal set cable), power the console back on and restart your game.
ATTACHING THE PEDAL SET TO A COCKPIT
- Attach the pedal set using the small screw threads located on the underside of the pedal set.
- Screw M6 screws (not included) into the cockpit’s pedal support plate and into the small screw
threads located on the underside of the pedal set.
Important: The length of the M6 screws must not exceed the thickness of the cockpit’s pedal
support plate plus an additional 10 mm, to avoid damaging the pedal set’s internal components.
To be handled only by users
16 years of age or older
HEAVY PRODUCT
Be careful not to drop the product on
yourself or on anyone else!

6/17
INSTALLING THE 2 LATERAL ARCHES (1)
Positions of the pedal set’s 2 lateral screw threads (1 upper + 1 lower) in order to attach the 2 lateral
arches (1):
- Place one of the plastic washers (3) on the screw thread located on the lower part of the pedal set.
- Next, place one of the arches (1) on the screw thread located on the upper part of the pedal set
and on the plastic washer (3).
- Attach the arch (1) using 2 of the M8-type Allen screws (2)and the 6 mm Allen key (4) by turning
the screws clockwise.
- Repeat this procedure on the other side of the pedal set to attach the second arch.
You are now ready to play!

7/17
CONFIGURING THE PEDALS
Each of the 3 pedals features:
- A metal head (17) with several perforations
(9 for the accelerator – 6 for the brake – 6 for the clutch)
- A plastic head support (21) (between the head and the arm) with 4 perforations
- A metal pedal arm (22) with 4 perforations
CAUTION: To avoid any calibration problems, always disconnect the USB cable
from your steering wheel before adjusting the settings on your pedal set.
Adjusting the pedal HEIGHT
- Using the included 2.5 mm Allen key (20), loosen and remove the 2 screws holding the metal
head (17) and its support (21) in place.
- Once this is done, select the height of your choice and then replace and re-tighten the screws.
Examples with the accelerator pedal:
Low position
Medium position (default)
High position
Very high position
Number of possible height positions per pedal:
- 4 for the accelerator pedal
- 2 for the brake pedal
- 2 for the clutch pedal

8/17
Adjusting the pedal SPACING
- Using the included 2.5 mm Allen key (20), loosen and remove the 2 screws holding the metal
head (17) and its support (21) in place.
- Once this is done, select the position of your choice (to the left, in the center or to the right) and
then replace and re-tighten the screws.
Examples with the brake pedal:
Left position Center position (default) Right position
Number of possible spacing positions per pedal:
- 3 for the accelerator pedal
- 3 for the brake pedal
- 3 for the clutch pedal
Adjusting the pedal TILT
- Using the included 2.5 mm Allen key (20), loosen and remove the 2 screws holding the metal
head (17) and its support (21) in place.
- Once this is done, turn the plastic head support (21) 180°, and then replace and re-tighten the
screws.
Examples with the accelerator pedal:
Less tilted position More tilted position (default)
Number of possible tilt positions per pedal:
- 2 for the accelerator pedal
- 2 for the brake pedal
- 2 for the clutch pedal

9/17
Adjusting the range of TRAVEL and resistance FORCE of the brake pedal (with
no BRAKE MOD installed)
- Install the metal stop (23) at the rear of the brake pedal arm.
- Select your choice of position (Long, Medium or Short range of travel), and then tighten the 4 M3-
type Allen screws (8) using the included 2.5 mm Allen key (20).
Long travel and strong Medium travel and Short travel and
resistance (default)medium resistance weak resistance
Long travel and strong Short travel and
resistance (default) weak resistance
Number of possible travel or resistance positions:
- Long travel with resistance of approximately 22 lbs / 10 kg
- Medium travel with resistance of approximately 18.7 lbs / 8.5 kg
- Short travel with resistance of approximately 15.4 lbs / 7 kg
Note: the longer the travel, the stronger the pedal’s resistance (and vice versa).