Thuasne AeroSling II L3960 User manual

5.1 Detach sling from bolster and remove Waistband
Strap from Rigid Waistband. Insert arm into sling,
adjust strap and use foam handle as needed.
5.2 Waistband Strap may be used in conjunction
with Sling to provide additional immobilization.
Using Velcro provided, join both ends of the strap
(buckle and fabric) to create a belt. Fix the belt to
the side of the sling closest to the body using Velcro
already in place. Adjust belt length for a snug and
comfortable fit.
4615 Shepard Street, Bakersfield, CA 93313
800-432-3466
ThuasneUSA.com
AeroSling II
Shoulder Immobilizer
L3960
AeroSling II
Instructions
Please read the Instructions for Use completely before applying this product.
Hand wash
30°C with mild
detergent
Do not
tumble
Do not submerge
metal components
in water
Lay flat
to dry
Instructions for Care
L-0123 Rev C
Indications
Recommended for shoulder stabilization post-operatively, joint separation, muscle strain; anterior,
interior or posterior instability.
Warnings
This product is to be used under the supervision of a medical health professional. If you experience
any pain, swelling, sensation changes or any unusual reactions while wearing the product, discontinue
use and contact your medical professional immediately.
Brace Components
1. Rigid Waistband
2. Interior/Exterior Rotation Plate
3. 30° Abduction Bolster
4. 90° Abduction Bracket
5. Sling
6. Over Shoulder Strap
7. Waistband Strap
8. Foam Hand Grip
1
3
3
2
4
5
5
6
8
7
7
5.1
5.2
ADJUST
ADJUST
ADJUST
ADJUST
5. For use with Sling Only

AT TACH
TRIM
1
7
1. Fitting the Rigid
Waistband and Strap
FORM the Rigid Waistband (1) to fit the
patient’s waist on the affected side.
Attach the Waistband Strap (7) to the
Rigid Waistband using the Velcro
included. ATTACH the buckle end of
the strap to the anterior side of the
waistband just under the 30° Abduction
Bolster, the fabric end of the strap will
attach to the posterior side. TRIM strap
as needed for proper fit.
2. Apply and Adjust Sling, Shoulder Strap, and Cuff
RELEASE buckles and strapping. Place arm inside of sling with elbow positioned to the back
of the sling pocket. FOLD back cuff to accommodate patient arm length. Patient may grip
foam handle for additional comfort and support.
Place shoulder strap over unaffected shoulder and buckle into place at the front of the sling.
ADJUST strap length as necessary to ensure arm is supported.
4.1 With brace doffed, DETACH the 30° Abduction
Bolster (3) from Rigid Waistband by opening Velcro
covering behind the Internal/External Rotation Plate
(2) and removing the four exposed nuts. Detach
Bolster from Waistband (1).
4.2 With bolts still in place, apply the 90° Abduction
Bracket and reapply/tighten nuts. Attach 30°
Abduction Bolster to Bracket using bolts/nuts
provided.
4.3 Don Rigid Waistband and Bracket, ensuring the
brace fits snugly around the waist and at the correct
height. Fix sling to Bolster and adjust strap length as
necessary to ensure arm and shoulder are
supported. Reverse steps 4.1 - 4.2 to step brace
down to 30° abduction
AeroSling II
Instructions for Use
BUCKLE
BUCKLE
STRAP
30°
3. Using 30° Abduction Bolster
and Interior/Exterior Rotation
Plate
Fix Sling to 30° Abduction Bolster using Velcro
provided, patient’s shoulder will remain at 30°
abduction.
To adjust interior/exterior rotation bend the
Interior/Exterior Rotation Plate to desired
position and attach to Bolster using provided
Velcro. For internal rotation bend plate towards
waistband, bend out for neutral or external
rotation.
1
3
DETACH
4.1
2.1
SHORT
MEDIUM
LONG
FOLD
FOLD
FOLD CUFF
2.2
2
(x4) (x4)
(x4)
4.2
3.1
90°
4.3
ADJUST
4. Using 90° Abduction Bracket
FORM