ThunderDog B103 User manual

INSTRUCTION MANUAL
B103
Charging the Battery
Before using this product, fully charge the B103 headset unit by
plugging the charger into an AC outlet and inserting the connection pin
into the Charging Port on the headset.
Headset Functions
1. Power ON your headset:
2. Power OFF your headset:
Pairing the B103 Headset to Your Phone:
1. Turn your phone OFF entirely and then turn it back ON to refresh its Bluetooth memory.
2. Find the Bluetooth menu in your mobile phone turn the Bluetooth function ON.(Check your mobile phone user guide)
4. On your phone, perform a Bluetooth “device discovery” to add the B103 headset as a new device. It only takes a few seconds to search
& find the B103 Bluetooth headset.
5. When the B103 headset is discovered (found) the phone will display “B103”
6. If prompted by your phone to enter a code, enter; "0000" and the phone will now pair with the headset and be ready to use.
7. If supported by your phone menu, set the B103 as "set as authorized "or "add to trusted devices".
8. Keep the Bluetooth function on your phone ON with your phone near, the headset will automatically pair.
9. If the pairing is not successful, the headset will shortly return to the standby mode.. Please repeat the process to try the pairing again.
10. Refer to your phones User Manual for any additional steps.
Note: To conserve power, the unit automatically turns off when not paired with your Bluetooth Phone.
For Assistance please call 1-800-936-1168. Do NOT return this product to your retailer.
Operating the Headset:
2. To ANSWER or END a call:
3. To REJECT* a call:
4. To REDIAL* the last call:
Press the FUNCTION button twice.
5. To activate VOICE DIALING*:
6. To adjust theVOLUME:
3. With the B103 POWER OFF hold the headset 12” inches away from your mobile phone and Press and Hold the FUNCTION button
on the headset for about 6 seconds until the LED light flashes blue and red alternating which indicates your headset is in PAIRING MODE
and is now ready to be “paired” with your Bluetooth Mobile Phone.
Press the FUNCTION button once when there is an incoming call to answer. Press the FUNCTION button once again to end the call.
Press and Hold the the FUNCTION button (approx. 2-3 seconds) when there is an incoming call you want to ignore and send it to your voicemail.
While connected to your phone, Press and hold the FUNCTION button (approx. 2-3 seconds) until you hear two beeps.
Voice commands must already be recorded into your phone for this function to operate (see your phones user guide)
Click the VOLUME UP or VOLUME DOWN button during a call to adjust to the desired level. The volume level will be remembered by the
B103 for the next call.
* To use these functions, your phone/device must also support the Bluetooth Profile.
Press and Hold the FUNCTION button (approx. 2-3 seconds) until the blue
Press and Hold the FUNCTION button (approx. 2-3 seconds) until the
red indicator flashes twice and the power will turn off.
indicator flashes four times.
Charging port
Speaker
LED indicator
Function
button
Microphone
VOLUME (-)
button
VOLUME (+)
button
11. To pair a second phone, turn the headset OFF and repeat steps 3-10.
1.
To Change the VOICE PROMPT LANGUAGE:
The headset will cycle through available language options. Press the FUNCTION
button to confirm your language choice.
Press and Hold the FUNCTION button for about 6 seconds until the LED light flashes blue & red alternating. Now Press and hold the
FUNCTION button until you hear a beep.

Bluetooth Specifications V3.0
Bluetooth Profiles Supported Headset, Handsfree
Transmission Power Class 2
Operation Range Up to 10 Meters
Frequency Range 2.402~2.4835 GHz
Battery Built-in Rechargeable
3.7V Li-polymer Battery
Charging Voltage DC4.75-5.25V
Charging Time About 2 hours
Talk Time*
Up to 5 hours
Standby Time* Up to 200 hours
Dimensions (mm) L51 X W15 X H10
Weight About 10g
Speaker Dimension 10mm
Mic Model 4015
*May vary due to user’s operation mode and device settings
Specifications
Power on
Power off
Standby mode
Pairing mode
Active call
Low battery
Charging
Charging complete
LED indicator chart
LIMITED 90-DAY WARRANTY
We warrant this product to be free from defects in material and workmanship under normal use for a ninety-day period from the original date of
purchase by the original purchaser from an authorized THUNDERDOG dealer. We will repair or replace the unit free of charge should it become
defective under this warranty.
Should you be missing any parts, please contact the retailer or Technical Support Center to secure a replacement for those parts.
THUNDERDOG will warrant for a period of ninety-days from the original date of purchase, the unit and all accessory components described in the
Instruction Manual. The warranty covers defective materials and workmanship and is applicable only under normal use. This model is not intended for
outdoor use. This warranty does not cover any product, which has been subject to damage due to improper assembly or disassembly, an act of nature,
misuse, neglect, accident, abuse, commercial use, or modification of, or to, any part of the product. Also not covered are labor or assembly costs,
products purchased from unauthorized THUNDERDOG sellers or costs incurred in shipping the unit or part for warranty repair. Under no circumstances
shall THUNDERDOG, be liable for any loss (direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage arising out
of, or in connection with, the use of this product.
This warranty does not cover product sold ‘As Is’.
This warranty is valid only to the original purchaser of the Product in the United States and Canada and grants specific legal rights.
Blue indicator blinks 4 times
Red indicator blinks 2 times
Blue indicator blinks once
every 2 seconds
LED indicator does not blink
Flashing Blue and Red Light
Blue indicator blinks rapidly
All Blue indicators will
change to Red
Steady Red Light
Steady Blue Light
Power Conservation
mode
Note: Power Conservation mode means your headset maintains a connection
with your phone but is conserving power and will wake up when any function is activated.
Our Customer Support Center is available Monday - Friday (9:00AM to 9:00PM EST) and Saturday (9:00AM to Noon) for technical assistance or
troubleshooting. To contact us, please call 1-800-936-1168.