TiGHT AV SPK1-C650T-WH User manual

User Manual
SPK1-C650T-WH
6,5" 2-Way Ceiling Speaker, 70/100V and 8Ohm, 50W RMS
All Rights Reserved
Version: SPK1-C650T_2022V1.0

6,5" 2-Way Ceiling Speaker, 70/100V and 8Ohm, 50W RMS
1
Statement
Read this user manual carefully before using this product. Pictures shown in this manual are for reference only, different model and
specifications are subject to real product. This manual is for operation instruction only, not for any maintenance usage. The
functions described in this version are updated by November 2022. In the constant effort to improve our product, we reserve the
right to make functions or parameters changes without notice or obligation. Please refer to your distributor for the latest details.
Safety Precaution
To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further
reference.
Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
Do not expose the unit to rain, moisture or install this product near water.
Do not use liquid or aerosol cleaners to clean this unit.
Refer all servicing to qualified service personnel.
Prior to installing the speakers into any ceiling/wall, check the structure for weight bearing ability and avoid contact with any
wiring or plumbing that might be behind the surface area. Installing on soft materials or in areas incapable of supporting the
speakers weight may cause personal injury or damage to the speaker.
Make sure the speaker is properly secured to the ceiling/wall. Please use the proper screws, bolts, or anchors. Failure to do so
may cause the speaker to become unsecured and cause potential damages/injuries.
Damage to the woofer and tweeter may occur if the speaker is dropped or hit and resulting in no sound or distorted sound.
Never overdrive your speakers to the point of distortion and always reduce volume prior to switching input sources.
Use only approved and certified wiring in your installation, do not stretch or place the wire in contact with sharp objects.
Prior to removing cables ensure all power to your amplifier and other components is turned off.
Customer Service
We provide limited warranty for the product within five years counting from date of purchase (The purchase invoice shall prevail).
Note: Please contact your distributor immediately if any damage or defect in the components is found.
Introduction
The TiGHT AV SPK1-C650T-WH is a full-range coaxial ceiling speaker consisting of a 6.5 inch polypropene cone and a 0.5 inch
mylar dome tweeter. It features combined 70V/100V and low impedance operation mode. The ceiling speaker also features easy-to-
install spring clamps “dog-legs” and a white flat magnetic grille.
Features
6.5 inch polypropylene cone driver with rubber edge
0.5 inch mylar dome tweeter
Supports both 70V/100V and low impedance operation
70V: 1.25W-2.5W-5W-10W & 8Ω
100V：2.5W-5W-10W-15W & 8Ω
Magnetic flat grille that comes in white color.

6,5" 2-Way Ceiling Speaker, 70/100V and 8Ohm, 50W RMS
2
Specifications
RMS Power 50W
Impedance 8 Ω (in low-impedance setting)
Sensitivity(1m/1W) 88dB
Max SPL (1m) 105dB (low-impedance)*
Frequency Range (-10dB) 65Hz-20kHz
Woofer Type 6.5" Polypropylene cone with rubber edge
Tweeter Type 0.5"(13mm) Mylar dome tweeter
Crossover Slope 6dB/Octave
Dimension Φ227X103mm
Cutout Size Φ210mm
Ceiling Thickness Spring clamps can support up to 30mm ceiling
thickness
Net Weight 1.25 kg
Shipping Weight 1.50 kg
Grille Magnetic round grille. Color: White
Transformer
Knob Style
70V：1.25W-2.5W-5W-10W & 8Ω,
100V
：
2.5W-5W-10W-15W & 8Ω
Environmental Compliance RoHS
Warranty Limited 5 years warranty
* Half-space (in ceiling)
Package List
Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged,
please contact your distributor for a replacement.
Speaker Grille Cutout Template User Manual
Installation
①Cut the speaker hole
Use a stud finder to locate an area that is free of obstructions or studs. Position the cutout template where you are installing the
speaker. Trace the template to mark out the speaker location with a pencil. Drill a pilot hole and cut all of the way around the circular
outline with a cutting saw.
②Set the operation mode
Use the knob located on the backside of the speaker to select operation mode and tap settings for 70V/100V mode.
C 1 2 3 4
100V
8ohm
15W
10W
5W
2.5W
70V
8ohm
10W
5W
2.5W
1.25W

6,5" 2-Way Ceiling Speaker, 70/100V and 8Ohm, 50W RMS
3
③Connect speaker cable
Ensure that the amplifier is not connected or turned off before connecting speaker cables. Pull the speaker cable out of the hole which
you have cut and connect it to the speaker.
④Install the speaker
Set the spring clamps “dog-legs” aside and place the speaker into the ceiling. Then use the screwdriver and gently tighten the
four screws on the front of the speaker to secure the speaker. Do not apply to much force as this can break the spring clamps.
⑤Attach the magnetic grille
As several magnets are on the speaker frame, attach the grille to the rim of the speaker directly. Ensure the grill is attached to the
speaker securely to keep the grille from falling.
Note: Anytime you note distortion, reduce the volume. Never allow your amplifier to be driven into "clipping". Otherwise, the
speakers may be damaged. Damage caused by operating the speakers at distorted volume levels is not covered by the warranty.