Timbertech RadianceRail User manual

RadianceRail®
Installation Guide
decking | railing | lighting | fastening timbertech.com
Installing RadianceRail®with Balusters ............................................................................................................ 2
Installing RadianceRail®Stairs with Balusters................................................................................................... 7
Notes ........................................................................................................................................................ 11
ATI Architectural Testing, Inc.
CCRR-0114 • RadianceRail & RadianceRail Express
TimberTech Code Listings
Once a product is tested by an independent lab, an application and report is submitted to one of several agencies that provide listings for building
products that meet the requirements of Acceptance Criteria 174 (AC 174) as set forth by the International Code Council Evaluation Service (ICC-ES).
TimberTech currently has listings from the ICC-ES and Architectural Testing Inc. The following TimberTech reports on code compliance are available
to download on www.timbertech.com.
For the most up-to-date code listings visit
www.timbertech.com/installation.
• Please read all instructions completely before starting any part of the installation.
• TimberTech Rail should be installed using the same good building principles used to install wood or composite railing and in accordance with the local building
codes and the installation guidelines included below. TimberTech accepts no liability or responsibility for the improper installation of this product.
• TimberTech Rail may not be suitable for every application and it is the sole responsibility of the installer to be sure that TimberTech Rail is fit for the intended use.
Since all installations are unique, it is also the installer’s responsibility to determine specific requirements in regards to each Rail application.
• TimberTech recommends that all applications be reviewed by a licensed architect, engineer or local building official before installation. If you have any questions
or need further assistance, please call TimberTech Customer Service at 1.800.307.7780 or visit our website at www.timbertech.com.
• TimberTech Railing is tested as a whole system and should be used that way. It is not intended to be used in conjunction with other railing systems or fasteners.
• The following Installation Guidelines are applicable for installation of TimberTech RadianceRail railing.
• IMPORTANT: Make sure the DRIVE TOOL/DRILL is configured or set to use the SCREW setting when driving and/or tightening all FASTENERS.
• SAFETY: Always wear goggles when handling, cutting, drilling and fastening materials.
• Failure to install this product in accordance with applicable building codes and TimberTech’s written Rail Install Guide may lead to personal injury, affect rail system
performance and void the product warranty.

Page 2
Installing RadianceRail
®
with Balusters
Measuring Your Railing Area
Important Information
Component Dimensions
Tools Required
Components Needed For Installing
One RadianceRail
®
Section
RadianceRail
®
is available in 10’, 8’, and 6’ lengths.
• Measurements are from center to center of the posts. Rails
are produced in 10’, 8’, and 6’ lengths to allow for finished
end cuts and angles.
• Determine how many 10’, 8’, and 6’ RadianceRail sections
you need and check to be sure you have all the components
(and quantities) listed in the chart shown to the right.
• RadianceRail 10’, 8’, and 6’ Rails are designed not to exceed
10’, 8’, and 6’’ center of post to center of post, respectively.
•For stair applications maximum rail length must not exceed 91”
• Cut slowly, using a fine tooth saw blade to avoid chipping.
• For 42” railing use 12’ Post Sleeves.
• Custom Rail Packs should be used when installing Aluminum
Balusters.
• Miter Saw
• Drill
• Measuring Tape
• 7/64” Drill Bit
• 3/16” Drill Bit
Components Included
in Complete 6’ and 8’
Kits (white only).
Visit www.timbertech.com/installation to view TimberTech installation videos.
Consult your local building codes for guard and handrail requirements.
Components available
separately for
mix-and-match rail
systems
Additional Components
Needed for Each
System
1 - Top Rail
1 - Bottom Rail
2 - Support Rails
Foot Blocks
- 1 in 6’ kits
- 2 in 8’ Kits
Square Balusters
-13 in 6’ Kits
-18 in 8’ Kits
Hardware Mounting Kit
Support Block Mounting Templates
Baluster Screw Kit
1 - Top Rail
1 - Bottom Rail
2 - Support Rails (1 - Aluminum Top Support Rail for 10')
Hardware Mounting Kit
Support Block Mounting Templates
Foot Blocks
- 1 in 6’ Packs, - 2 in 8’ Packs, - 3 in 10’ Packs
RadianceRail Pack
Baluster Pack
Hardware Mounting Kit
4 - Mounting Brackets
2 - Support Blocks
16 - #8 x 3/4” Screws
6 - #8 x 1 3/4” Screws
6 - #8 x 2 5/8” Screws (Stairs Only)
3 - #8 x 3” Screws
12 - #8 x 3” Green Screws
T20 Driver Bit
2 - Post Caps
2 - Post Sleeve
2 - Post Skirts
5”
5”
2.9”
3”2.25”
2.5”
1.8”
1.8”
1.25”
1.25”
.75”
Top Rail
Post Sleeve
Bottom Rail
Support Rail Square
Composite
Baluster
Round
Aluminum
Baluster
Square
Aluminum
Baluster
Post Cap (2)
Top Rail (1)
Mounting Bracket (4)
Support Rail (2)
Support Block (2)
Bottom Rail
Post Sleeve (2)
Composite Baluster
(23 in 10’ Section)
(18 in 8’ Section)
(13 in 6’ Section)
Aluminum Baluster
(25 in 10’ Section)
(20 in 8’ Section)
(15 in 6’ Section)
Post Skirt (2)
Foot Block
(3 in 10’ Section)
(2 in 8’ Section)
(1 in 6’ Section)
.75”
.75”
.75”
Baluster Screw Kit
18 - #8x2” Screws
18 - #8x3” Screws
Baluster Screw Kit
20 - #8x2” Screws
20 - #8x3” Screws
Composite Balusters
- 18 Balusters per Pack
(23 required per 10’ section)
(18 required per 8’ section)
(13 required per 6’ section)
- 29” for 36” Railing
- 31” for 36” Railing
(with less than 2” gap
between deck & Bottom Rail)
- 35” for 42” Railing
- 37” for 42” Railing
(with less than 2” gap
between deck & Bottom Rail)
Aluminum Balusters
- 20 Balusters per Pack
(25 required per 10’ section)
(20 required per 8’ section)
(15 required per 6’ section)
- 29” for 36” Railing
- 31” for 36” Railing
(with less than 2” gap
between deck & Bottom Rail)
- 35” for 42” Railing
- 37” for 42” Railing
(with less than 2” gap
between deck & Bottom Rail)
Hardware included in
Hardware Mounting
Kits:

Page 3
Installing RadianceRail
®
with Balusters
1/3
1/3
1/3
1/2
1/2
1 2
3
• Trim Post Sleeves
to desired length.
39” above deck surface is
optimal for 36” railing heights.
•Slide Post Sleeve and Post
Skirt over post (do not
force).
•Ensure post are
square and plumb.
INSTALL POST
SLEEVES
INSTALL LOWER
SUPPORT BLOCK
•Position template at
bottom of Post Sleeve
above Post Skirt.
If you do not have a the template, position
the top of the Support Block 4” above the
deck and 2-1/2” above the post skirt.
CUT AND ASSEMBLE
BOTTOM SUPPORT
RAIL
•Cut the Bottom
Support Rail to
length.
For sections up to 6’: Place one Foot Block in the center of the rail
For sections 6’ to 8’: Space two Foot Blocks approximately at 1/3 intervals on the rail
For sections 8’ to 10’: Space three Foot Blocks approximately at 1/4 intervals on the rail
45°
Straight Section
Angled Section
Center screw aligned to
rail centerline
Foot blocks
8’ Section
6’ Section
Center screw
aligned to rail
centerline
Bracket set
flush to rail
face
Bracket set
flush to rail
face
For angled rail installations, align
angled face of Support Block
parallel to rail section.
Optimal 39” 4”
2.5”
Template
Support
Block
Post Skirt
Pre-Drill 7/64”
#8 x 3” Coated
Screws
Pre-Drill 7/64” for Brackets
#8 x 3/4” Coated Screws
Pre-Drill 7/64”
#8 x 3” Coated Screws

Page 4
Installing RadianceRail
®
with Balusters
4
5
INSTALL BOTTOM
SUPPORT RAIL
SPACE BALUSTER
AND
TRIM RAILS
The space between the end baluster and post can not exceed 4”
• Position Bottom
Support Rail assembly
onto Support Blocks.
• Measure distance between
the posts at the Bottom
Support Rail.
• Transfer measurement to Bottom
Rail and center either on a pre-drilled
hole or between two pre-drilled holes.
• Cut Bottom Rail and Top Support Rail
to length.
#8 x 3” Green
Coated Screws
Centerline
Odd number of balusters
Even number of balusters
7/64” Pre-Drill
#8 x 3” Green
Coated Screws
Bottom
Rail
Top
Support
Rail

Page 5
Installing RadianceRail
®
with Balusters
6
7
ASSEMBLE BALUSTER
SECTION
INSTALL RAIL
ASSEMBLY
• Attach Mounting Brackets
at each end of the Top
Support Rail as outlined in
Step 3.
Position rail assembly with lip of
Bottom Rail toward outside of
deck, over bottom Support Rail.
• Align top Support Rail to
center of posts.
Top Support
Rail
Bottom Rail
Lip (facing out)
See step 3 for
bracket installation
#8 x 3” Coated
Green Screws
Align to center
of post
7/64” Pre-Drill
#8 x 3” Coated Screws
Pre-Drill 7/64”
#8 x 3/4” Coated Screws
#8 x 2” Coated Screws

Page 6
8INSTALL TOP RAIL
AND POST CAPS
• Measure and cut Top Rail to
length. Trim both ends for a
clean cut.
• Attach Post caps using exterior
grade caulk applied to the
underside of the cap.
Caution: Screws must be 1 3/4” so they won’t go through the Top Rail on straight rail sections.
Post Cap
Top Rail
Pre-Drill 3/16”
#8 x 1 3/4” Coated Screws
Installing RadianceRail
®
with Balusters

Page 7
Installing RadianceRail
®
Stairs with Balusters
Top Rail Length
Bottom Rail Length
1 2
• Trim Post Covers
to desired length.
•Slide Post Cover and Post Skirt
over post. Do not force.
•Ensure post are
square and plumb.
INSTALL POST
COVERS
TRIM RAILS
TRIM RAILS
Support Rails are rotated 90° for
stair rail applications.
•Trim both the
Top Support Rail
and the Bottom
Support Rail to
those dimensions.
Test fit rails
to check for
accuracy.
• Transfer measurement from
Bottom Support Rail to
Bottom Rail.
• Determine
measurements
and angle as shown.
• Trim Top Rail to match Top
Support Rail at appropriate
angle.
Stair Angle
Right Wrong
3
Bottom Rail
Top Rail
Top Support Rail
Bottom Support Rail

Page 8
Installing RadianceRail
®
Stairs with Balusters
4 5
Drill Baluster
Holes
TRIM BALUSTERS
ASSEMBLE
BALUSTER
SECTION
6
• Place the Bottom Rail
and the Top Support Rail
together as shown to
keep the holes aligned.
• Separate the
two rails, once
all holes are
drilled.
Drill 3/16” hole through the top Support
Rail using the Bottom Rail holes for
alignment, drilling at the same angle
used to cut rail ends.
Bottom Rail
and Top
Support rail
Pre-Drill 3/16”
Important: Start cut at top edge to
maximize the length.
Trim Baluster ends to required angle
as shown.
Aluminum stair Balusters are pre-cut
to a stair angle and are not to be cut
on the job site.
Bottom Rail
Top Support
Rail
Lip
(facing out)
Tip for Bottom Rail: Partially drive
screws into all Balusters before driving
them in completely.
Brackets must be on the side of the rail
facing the stairs.
• Attach Brackets to Top
Support Rail.
Pre-Drill 7/64”
#8 x 3/4” Coated
Screws
Center screw
aligned with rail
centerline
Scrap Piece of
Wood Cut to
Stair Angle
#8 x 3” Coated Screws
#8 x 2” Coated Screws

Page 9
Installing RadianceRail
®
Stairs with Balusters
7
8
INSTALL BOTTOM
SUPPORT RAIL
INSTALL RAIL
ASSEMBLY
Pre-Drill through
Bottom Support
Rail ONLY with
3/16” bit
Bottom Support Rail
#8 x 3”
Coated Screw
• Wedge Foot Block under
Support Rail & attach.
#8 x 3” Green
Coated Screws
• Secure Mounting Brackets to
posts.
Pre-Drill
7/64”
• Attach Mounting
Brackets to
Bottom
Support Rails.
Pre-Drill 7/64”
#8 x 3/4” Coated
Screws
Center screw
aligned with rail
centerline
Brackets must be on the side of the rail
facing the stairs.
For sections up to 6’: Place one Foot
Block in the center of the rail
For sections 6’ to 8’: Space two Foot
Blocks approximately at 1/3 intervals on
the rail
Position and center rail
assembly over Bottom
Support Rail.
• Mark Ends of Top
Support Rail.
• Rotate Rail
assembly out of
way to fasten
Support Block.
• Secure Mounting
Brackets to Posts.
Pre-Drill
7/64”
#8 x 3”
Coated
Screws
Pre-Drill 7/64”
#8 x 3” Green
Coated Screws

Page 10
Installing RadianceRail
®
Stairs with Balusters
9INSTALL TOP RAIL
AND POST CAPS
• Position Top Rail over
Support Rail and attach
with screws.
• Secure Post Caps with
exterior grade caulk.
Pre-Drill 3/16”
#8 x 2 5/8”
Coated Screws
For typical stair angles, use
provided 2 5/8” screws to
fasten the Top Rail.

Page 11
Notes

RadianceRail®
Installation Guide
© 2014 TimberTech RRKITINSTALL (Balusters) | 02/14
TimberTech
894 Prairie Avenue
Wilmington, OH 45177
timbertech.com
1.800.307.7780