Timeguard LEDPRORFKB Manual

Installation & Operating Instructions
Dedicated PIR Light
Controller c/w RF remote
control for LEDPRO
Floodlights
Model: LEDPRORFKB – Black
Model: LEDPRORFKWH – White
Model: LEDPROFOB RF Remote Fob

1
1. General Information
These instructions should be read carefully
and retained for further reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the
mains supply to the PIR sensor is switched off
and the circuit supply fuses are removed or
the circuit breaker turned off.
• It is recommended that a qualified electrician is
consulted or used for the installation of this PIR
sensor and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including
when this PIR sensor is fitted does not exceed the
rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
PIR Light Controller
• Operating Voltage: 230V AC 50Hz
• This product is of Class I Construction and must
be earthed.
•Detection Angle: 180°

2
• Motion Detection Range:
Up to 12m distance at a 2.5m mounting height
• Maximum Switchable Load;
140W LED Lighting
1000W Halogen Lighting
200W CFL Lighting
500W Fluorescent tube w/o PF correction
• Time ON Adjustment: 3 seconds – 18 minutes
• Warm Up Period: Approximately 35 seconds
• Dusk (LUX) Level Adjustment: 2 – 1000 Lux
• Operating Temperature: -20°C to +40°C
• Standby (W): <0.5W
• Manual Override Mode:
ON/OFF operation using RF Remote Fob (6 fobs max)
•Sensor Head Adjustment:
Pan angle = Left/right 90°, Tilt angle = Down 150°
• RF Module: RX Receiver
• RF Frequency: 433.92MHz
•IP55 Rated suitable for restricted external applications
• CE Compliant
• Dimensions (H x W x D): 114 x 78 x 127mm
RF Remote Fob
• Battery: 3V (1x CR2032)
• Battery Life:
Approximately 24 months (@ 10x opt/day)
• Class Rating: Class III

3
• Transmission and Receiving Distance:
100m hand held (clear line of sight)
10m when mounted inside a wall switch
(recommended mounting height = 1.2m)
• Total number of fobs usable per PIR: 6
• Operating Temperature: -20°C to +40°C
•RF Module: TX Transmitter
• RF Frequency: 433.72MHz to 434.12MHz
• IP44 Rated suitable for restricted external
applications
• CE Compliant
• Dimensions (H x W x D): 60 x 38 x 15mm
4. Pack contents
• 1x LEDPRORFKB-WH Dedicated PIR Light Controller
c/w RF remote control for LEDPRO Floodlights
• 1x LEDPROFOB RF Remote Fob
• 1x Instruction Manual
• 1x 3V CR2032 Battery
• 1x Lens Sticker
• 2x Wire (for wall mounting a fob)
5. Selecting a Location
• The light controller has number of detection zones,
at various vertical and horizontal angles as shown
(see diagram A).

4
• A moving human body needs to cross/enter one
of these zones to activate the light controller.
The best all-round coverage is achieved with the
unit mounted at the optimum height of 2.5 metres.
• Careful positioning of the light controller will be
required to ensure optimum performance (see
diagram A detailing detection range and direction).
• The light controller is more sensitive to movement
ACROSS its field of vision than to movement
directly TOWARDS (see diagram B). Therefore
position the unit so that the light controller looks
ACROSS the likely approach path.
• Avoid positioning the light controller where
there are any sources of heat in the detection
area (extractor fans, tumble dryer exhausts etc.)
including opposite any other light sources such
as other security lights.
• Reflective surfaces (i.e. pools of water or white
painted walls) and overhanging branches may
cause false activation under extreme conditions.

5
6. Installation
6.1 Ensure the mains supply is
switched off and the circuit
supply fuses are removed or
the circuit breaker turned off.
6.2 An isolating switch should be installed
to enable the power to be switched ON & OFF
for maintenance purposes.
• During extreme weather conditions the motion
light controller may exhibit unusual behaviour.
This does not indicate a fault with the light
controller. Once normal weather conditions return,
the light controller will resume normal operation.

6
6.3 Remove the jumper plug from the floodlight.
6.4 Pass the 230V 50Hz mains supply and load
cables the holes provided on the PIR ensuring
that a cable gland, grommet or sealing
compound is used to maintain the IP rating.
6.5 Terminate the cables into the terminal block
ensuring correct polarity is observed and that
all bare conductors are sleeved (See section 7.
Connection Diagram).
6.6 Ensure that all connections are secure.

7
6.7 Connect the 3 way PIR plug, by pushing the
plug and socket inside the floodlight together
until they lock. DO NOT FORCE. THE PLUG AND
SOCKET WILL ONLY FIT TOGETHER ONE WAY
AROUND (See Jumper Plug diagram).
6.8 Secure the PIR to the floodlight using the
4 fixing screws.

8
7. Connection Diagram
• Connect the cables to the terminal block as follows;
• Note: The Switch Live terminal is for additional
standalone floodlights (see section 3. Technical
Specifications for maximum switchable loads).
Any floodlight connected to the L1 switch live
terminal ‘Live Output’ will be controlled by the PIR

9
8. Setting Up
Walk Test Procedure (Test Mode)
• The sensor will rotate from left to right, and will
tilt downwards. Adjust the light controller to point
in the required direction and angle down to limit
forward range as required.
• Set the two adjustment controls on the underside
of the unit to the following positions:
TIME ADJUST – Fully anti-clockwise
DUSK/DAWN LEVEL ADJUST – Fully clockwise
• Turn the power to the unit ON.

10
• The floodlight will illuminate for approximately
35 seconds. This indicates the unit is wired
correctly. The unit is in Test Mode when the light
turns OFF.
• If the detection area is too big for your
requirements, try angling the PIR light controller
head downwards. This will reduce the detection
area should a smaller coverage be required.
Setting Up for Automatic Operation
(Auto Mode)
• When walk tests are complete, the unit can be set
into Auto Mode.
• The TIME ADJUST setting controls how long the
unit remains illuminated following activation
and after all motion ceases.
• The minimum time (fully anti-clockwise) is approx.
3 seconds, whilst the maximum time (fully
clockwise) is approximately 18 minutes.
• Set the control to the desired setting between
these limits.
• The DUSK/DAWN LEVEL ADJUST control determines
the level of darkness required for the unit to start
operating. The DUSK adjustment knob is indicated
by the ‘Moon’ and ‘Sun’ symbols).

11
• Set the light threshold to maximum (fully clockwise/
Sun end), then turn the control anti-clockwise
about three quarters of the way round to the
Moon end. This will give operation after
DUSK approximately.
• For a more accurate setting of the DUSK/DAWN
LEVEL ADJUST control turn it fully anti-clockwise
(Moon end) and leave for at least 20 seconds for
the unit to settle.
• When the ambient light level reaches that required
for DUSK, adjust the DUSK control a small amount
clockwise pausing to try to get the unit to detect
and turn the lights under control ON by moving
a hand slowly backwards and forwards across the
front of the detector lens for around 5 seconds.
• Continue to turn the control small amounts in
a clockwise direction, stopping after each
adjustment to try to get the unit to detect as above.
• Eventually detection will occur and the DUSK level
is now set as required.

12
10. RF Remote Fob
Battery
• To access the battery holder,
remove the back plate from
the fob as shown in
the diagram.
9. Masking the PIR Light
Controller Lens
•To reduce the PIR light controllers coverage,
preventing detection in unwanted areas, mask the PIR
light controllers lens using the lens sticker supplied.
• The top section of the lens covers long range
detection, the bottom covers short range.
Similarly the left and right lens sections cover
the left and right detection area respectively.
• Mask the PIR Light controllers lens to suit
your installation.

13
Pairing the RF Remote Fob(s) with the PIR
Light Controller
Note: You must complete the Walk Test Procedure
before you can pair the devices. The pairing of the
fob(s) cannot be actioned with the PIR light controller
set to Test Mode. Make sure the PIR light controller is
functioning correctly and set for Automatic Operation
(Auto Mode) before you continue.
•Press the centre button that
is located on the bottom
of the PIR light controller once
(do not press and hold for
longer than 4 seconds), the
lamp will flash twice to indicate
it is ready to pair your fob(s).
Note: once the lamp has flashed twice, the PIR
sensor will no longer trigger the lamp with motion
until the pairing sequence has been completed.
• Press the fob button once.
The lamp will turn ON
for 3 seconds, and back
OFF again, to indicate
it has been registered.

14
Note: If you have more than one fob to pair
(Up to 6 max) then press the fob buttons, one at a
time, waiting for the lamp to turn ON for 3 seconds
and back OFF again each time, between presses.
You cannot pair a 7th fob. If attempted, the lamp
will flash twice to indicate it has not been paired.
• After the last fob press, wait for approximately
30 seconds until the lamp flashes twice.
This will indicate that your fob(s) have successfully
been paired.
Note: once the lamp has flashed twice, the PIR
light controller will begin to trigger with motion
once again.
• Test your fob(s) by pressing the fob button once to
turn the lamp ON, and once to turn the lamp OFF.
If you are using more than fobs, you are able
to turn the lamp ON using one fob, and turn
the lamp OFF using another.

Remove
rubber caps
15
• Using 2 of the wires supplied,
push them firmly into the 2 spring
clamp terminals. Check they are
both secure with a light tug.
Erase all RF Remote Fobs from the PIR
Light Controller
• Press and hold the centre button, located on the
bottom of the PIR light controller, for approximately
5 seconds. The lamp will flash 5 times. This
indicates that un-pairing has been successful.
Installing a RF Remote Fob into a Wall Switch
• Remove the rubber caps from
the bottom of the fob as shown.

Dry Contact
w/o 230V AC Potential
16
• Follow the wall
switch wiring
image for
connection.
11. Troubleshooting Guide
PROBLEM
•Lamp stays
ON all the time
night and day.
SOLUTION
Check wiring connections.
Wires to L and L’ terminals may
be transposed.
•Lamp stays
ON all the
time at night,
or PIR keeps
activating at
random for
no apparent
reason
The unit may be suffering from false
activation. Cover the sensor lens completely
with black PVC tape. This will prevent the
sensor from ‘seeing’ anything. If the unit
now switches off after the set time duration
and does not re-activate, this indicated that
the problem was caused by false activation.
The problem may be solved by slightly
adjusting the direction/angle of the sensor
head (see previous section). If however, the
unit continues to remain ON or to operate
randomly then the unit is faulty and should
be replaced.

17
•PIR sensor
will not operate
at all.
Check that the power is switched ON at the
circuit breaker/internal wall switch.
Turn OFF the power to the unit and check
the wiring connections as per the diagram
(see 7. Connection Diagram).
Ensure no connections are loose.
Check the bulb (if it’s replaceable). If the
bulb has failed, replace (do not hold the
bulb directly with fingers, use a tissue or
clean dry cloth).
Where relevant, ensure the bulb is seated
correctly in the bulb holder.
•The PIR sensor
will not operate
at night.
Refer to section 8. Setting Up for DUSK
control adjustment.
•Unit activates
during the
daytime.
Refer to section 8. Setting Up for DUSK
control adjustment.
You may not be allowing the unit time to
complete its warm-up period. Stand well out
of the detection range and wait (the warm-
up period should never exceed 5 minutes).
Occasionally, winds may activate the sensor.
Sometimes passages between buildings
etc. can cause a “wind tunnel” effect.
Ensure the unit is not positioned so as to
allow detection of cars/people using public
thoroughfares adjacent to your property.
Ensure that the unit is mounted securely,
even the slightest movement can result
in a false detection.

18
3 Year Guarantee
In the unlikely event of this product becoming faulty due to
defective material or manufacture within 3 years of the date
of purchase, please return it to your supplier in the first year
with proof of purchase and it will be replaced free of charge.
For the second and third years or any difficulty in the first year
telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible
replacements (where agreed by Timeguard) the customer is
responsible for all shipping/postage charges outside of the
UK. All shipping costs are to be paid in advance before a
replacement is sent out.
•PIR coverage is
poor/ sporadic.
Unit may be poorly located. See Section
5. Selecting a Location and re-locate
the unit.
•Detection range
varies from day
to day.
PIR sensors are influenced by climatic
conditions. The colder the ambient
temperature, the more effective the sensor
will be. You may need to make seasonal
adjustments to the sensor head position
to ensure trouble-free operation all year
round.

67.058.622 (Issue 2)
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [e-mail]
For a product brochure please contact:
Qualified Customer Support Coordinators will be online
to assist in resolving your query.
If you experience problems, do not immediately
return the unit to the store.
Telephone the Timeguard Customer Helpline:
HELPLINE
020 8450 0515
or email [e-mail]
www.timeguard.com
Zerofour – June 2018