Timeguard TLRX05 Manual

INSTALLATION & OPERATING
INSTRUCTIONS
RECEIVER
CONTROLLER
Cat No. TLRX05
iTLRX05_Instructions.qxd 1/19/05 11:59 AM Page 1

1
Introduction
The TLRX05 In Line Receiver is part of the Timeguard
range of products which communicate by radio
frequency (r.f.) signals.
This enables substantial amounts of wiring to be
eliminated which is particularly useful in long runs
and coverage of outbuildings.
It is an In Line Receiver which receives r.f. signals from
transmitters it has been programmed to recognise and
turns connected lighting on.
In the following instructions products with catalogue
numbers including Tx (ones that send information
about PIR detection) are referred to as Tx units and
products with catalogue numbers including Rx (ones
that receive information about PIR detection) are
referred to as Rx units.
AC
Wall fixing hole
Wall fixing hole
iTLRX05_Instructions.qxd 1/19/05 11:59 AM Page 2

2
Output cable
to light
Mains supply
IN
Program/reset
button
Time
ON/Test
BD
Indicator
LED
Parts included
• In Line receiver unit.
• Instruction manual. Please keep safe for future
reference.
• Accessory Pack.
Tools and parts needed
• Electric/hand-held drill & bits.
• Terminal or Electricians screwdriver.
• Large slotted/philips screwdriver.
• Wire cutters.
Selecting a location
This unit can be used to control lighting indoors or
outdoors. The unit is designed for use with fixed
wiring only. Ensure that the incoming and outgoing
cables are protected from water ingress by use of
silicon sealant around the cable inlets.
Do not attempt to install during wet weather, or if you
are suffering from nausea or dizzy spells or on
medication with similar side effects.
If in any doubt, consult a qualified electrician.
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 3

3
The In Line Receiver must be within transmission
range of your chosen transmitter. The In Line
receiver can be placed at any convenient break point of
the wiring connected to the luminaire it
is intended to control. We suggest that the Transmitter
is placed in its optimum position to give the coverage
and detection required, then the In Line receiver is
placed at a point where it can
receive the Transmitter`s signal. To ensure that the
Receiver is receiving the transmission signal. This will
be less than 100m away if walls or chain link fences
come between the Tx and Rx units - if there is any
doubt about whether communication will take place make
temporary installations before programming.
Installation
IMPORTANT
Switch off the electricity at the fuse box by removing
the relevant fuse or switching off the circuit breaker
before proceeding with the installation.
Remove the front cover of the TLRX05 by removing the
4 x cover fixing screws as (Fig A).
Mark position of the fixing holes. (Fig B).
Drill the holes. Insert the wall plugs into the holes.
PASS THE CABLE THROUGH THE INCOMING
AND OUTGOING CABLE GROMMETS BEFORE
FIXING THE UNIT TO THE WALL.
Allow approximately 100mm of cable to pass through
the grommet. (A template for this wire length is
provided on page 8 of this manual). Fit grommet into its
location hole ensuring a good seal.
Fix the unit to the wall. Take care not to overtighten the
screws to prevent damage to the mounting plate. If
using a power screwdriver, use the lowest torque
setting.
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 4

4
Connection
Connect the incoming mains cable through one of
the lower grommets and into the terminal block
as follows (see connection diagram):
NEUTRAL (Blue) N
EARTH (Green/Yellow)
LIVE (Brown) L
Ensure the connectors are secure.
Connect the cable connected to the switched
luminaire through the upper grommet to the
terminal block as follows (see connection
diagram Fig B):
NEUTRAL (Blue) N
EARTH (Green/Yellow)
LIVE (Brown) L1
Ensure the connectors are secure.
Replace front cover and fully tighten the 4 fixing
screws as (Fig A).
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 5

5
Programming
Each Rx unit needs to learn the codes involved in the
messages from all the Tx units which are required to
control it (up to 20).
Turn OFF/remove batteries from any Tx unit which is not
required to control this RX unit. Turn off any other Rx units.
If it is convenient more than one Rx unit can learn the code of
a Tx unit simultaneously in which case leave these Rx units
switched ON.*
** If introducing the TLTXK2 hand held transmitter
press the “1” button on this unit to activate the TLRX05.
***If the button is pressed for 5 seconds or more then all
the codes that have been learnt will be erased.
1
2
3
4
The Rx unit needs to be set in programme mode. This will
happen automatically up to 4 seconds after the Rx unit is
first powered up. It can also be set by pressing the
Programme/ Reset button for 1 to 2 seconds (pressing for 5
seconds or longer will erase all programming within the Rx
unit). In either case the Time On/Test control must be set to
Test which will give a 5 minute period of programme mode.
The lights under control of the Rx unit will turn on at the
start of this period indicating it is in progress.
Go to the Tx unit** to be introduced to the Rx unit and
move across the face of its PIR lens within detection
range causing it to detect (indicated by the lights under
control turning ON for most Tx units and by a flash
from the red LED on the TLTXDCB.
Return to the Rx unit and check that it has turned the
lamps under its control off (indicating correct code learning).
*Any other Rx units left connected should now be
checked in the same way.
Press the Programme/Reset button for 1 to 2 seconds*** if
the Rx unit is required to learn the code of another Tx unit.
*Any other Rx units required to learn the code of this
new Tx unit should be left connected.
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 6

6
5. If the lights did not go OFF in step 4 page 5 the Rx is
not picking up a signal. Check the radio signal path
between the Sensor and Receiver for any metal
obstructions (support beams, chain link fences etc).
These can block radio signals and interfere with signal
transmission. A way to check path if using the Battery
Powered Detector TLTXDCB is to set the Rx On time
dial to test, remove the sensor from its location and
walk the sensor around the Rx. As you walk, wave
your hand in front of the sensor Tx. Note when the it
turns the Rx light OFF, and re mount in that area.
Settings
After Programming, set the ON TIME dial.
To set how long the lamp will remain ON after the
TLRX05 hs received a signal from a Tx unit, set the ON
TIME dial on the RX to 1, 3 , 5 or 12 minutes. See fig D.
Manual override
The lamp can be turned on and off independently of
any transmission signal by switching the unit off/on
once in less than two seconds To return to Auto Mode
repeat this switching action.
Erasing all codes
Tx unit codes can be erased for reprogramming. To
erase codes, while the TLRX05 is powered, press and
hold the PROGRAM button for more than 5 seconds.
The light will turn on, go out and then turn on again.
This will clear the unit of all programmed codes and
place it back into the AUTO PROGRAMMING Mode.
Now return to the Programming Section.
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 7

7
Solution
1. The installation switch is turned off.
2. Light bulb is loose or burned out
3. Sensor is positioned too far from
receiver. Move Tx closer
1. Tx unit is installed in a dark
location.
2. Receiver is in Manual Override
Mode. Flip Transmitter wall switch Off
then On twice to place back into Auto
Mode
Receiver is in Manual Override. Flip
wall switch Off then ON twice to place
back into Auto Mode.
This is the Low battery signal. replace
batteries in the Transmitter.
2. The Tx unit is positioned too far
from receiver. Move Tx closer.
Problem
• Light will not
come on when
motion is
sensed.
• Light Comes on
in Daylight.
• Light Stays on.
• Light Flashes on
and off twice
when activated.
• Light comes on
irregularly
when motion is
sensed.
Troubleshooting guide
Power Supply:
Maximum Switchable Load:
Time On Adjustment:
Environmental Protection:
Transmission Range:
Conforms to Directives:
230 V AC ~ 50Hz
2000W (e.g. 4 x 500W
Tungsten Halogen)
1, 3, 5 and 12 minutes
IP44 (suitable for outdoor use)
Up to 100m (varies with
surrounding structures)
73/23/EEC and 89/336/EEC
Technical specifications
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 8

8
Incoming Wire Template
25mm
1”
Use this template to estimate incoming cable length
75mm
3”
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 9

HELPLINE
020-8450-0515
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND
020-8452-1112
or email [e-mail]
5 Year Guarantee
In the unlikely event of this product becoming faulty due to
defective material or manufacture within 5 years of the date
of purchase, please return it to your supplier in the first year
with proof of purchase and it will be replaced free of charge.
For years 2 to 5 or any difficulty in the first year telephone
the helpline on 020 8450 0515.
FIVE YEAR
GUARANTEE
5
iTLRX05_Instructions.qxd 1/19/05 12:00 PM Page 10