Timeguard LEDPRO70B Manual

Installation & Operating Instructions
Professional
Rewireable Floodlight
LEDPRO70B
Black
LEDPRO70WH
White
LEDPRO100B
Black
LEDPRO100WH
White

1
1. General Information
These instructions should be read carefully in full before installation and retained
for further reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the floodlight
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.
•It is recommended that a qualified electrician is consulted or employed
for the installation of this floodlight and that it is installed in accordance
with current IEE wiring and Building Regulations.
•Check that the total load on the circuit including when this floodlight is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.
• DO NOT place any object closer than 1 metre in front of the floodlight.
3. Technical Specifications
•230V AC 50Hz
• This PIR sensor is of class I construction and must be earthed
•Colour Temperature: 5000K
• Energy Efficiency: Class A+
•Operating Temperature: -20°C to +40°C
• IP65 Rated, suitable for restricted external applications
• Dimensions (H x W x D): 235 x 305 x 66mm
• CE Compliant
LEDPRO70B & LEDPRO70WH
• 70W LED Non replaceable lamp
• Energy Usage: 70kWh/1000h
• Lumen Output: Black = 7000lm, White = 7100lm
LEDPRO100B & LEDPRO100WH
• 100W LED Non replaceable lamp
• Energy Usage: 100kWh/1000h
• Lumen Output: Black = 10,000lm, White = 10,200lm

2
4. Installation
•Ensure the mains supply is switched off and the circuit supply fuses are removed
or the circuit breaker turned off.
• An isolating switch should be installed to enable the power to be switched
ON and OFF to the floodlight. This allows the unit to be easily switched OFF
for maintenance purposes.
• Mark the position of the mounting holes on the wall using the U bracket
supplied as a template.
• Drill the holes for the wall plugs ensuring not to infringe on any gas/water
pipes or electrical cables that may be hidden below the surface.

3
•Fix the U bracket to the wall using the correct screws for the wall plugs being used.
Note: Ensure that when you mount this, the slots at the end of the bracket open
upwards to allow you to easily attach and secure the floodlight when ready.
•Attach the floodlight to the U bracket fitted to the wall. You can pre-fit the
supplied fixing screw/bolt and washers to the floodlight before you do this,
the screws/bolts will just need to be loose enough to fit over the upward-facing
slots at the end of the U bracket. Make sure the washers are in the correct order
as per the diagram. When the floodlight is in place, secure the screws/bolts,
ensuring not to overtighten.

4
• Pass the supply cable through the holes(s) provided in the backplate ensuring
that a cable gland, grommet or sealing compound is used to maintain the
IP rating of the floodlight.
•Terminate the supply cable into the terminal block (see section 5.
Connection diagram) ensuring correct polarity is observed and that
all bare conductors are sleeved.
•Attach the backplate to the floodlight, and apply pressure to the top and
bottom, then secure all four fixing screws ensuring not to overtighten.

230V 50Hz Mains Supply
Live Supply (Brown or Red) to L
Neutral Supply (Blue or Black) to N
Earth (Green/Yellow) to
5
5. Connection Diagram
•Connect the 230V 50Hz mains supply cable as follows;
Note: the L1 terminal is a Switch Live “Live Output” for slave floodlights
(when used in conjunction with the Timeguard LEDPROSLB-WH, LEDPRORFKB-WH
PIRs or the LEDPROPCB-WH Photocell).

6
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material
or manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge. For years
2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/postage
charges outside of the UK. All shipping costs are to be paid in advance before
a replacement is sent.
6. Operation
•Turn the power ON and test for normal operation.
7.Lamp Adjustment
•The floodlight can be tilted as per the diagram.

Zerofour – September 2018
67-058-637 (Issue 2)
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [e-mail]
For a product brochure please contact:
If you experience problems, do not immediately return the unit
to the store. Telephone the Timeguard Customer Helpline:
Qualified Customer Support Coordinators will be online
to assist in resolving your query.
HELPLINE
020 8450 0515
or email [e-mail]
www.timeguard.com