Timewatch FB2000 User manual

Manual
Flap Barrier FB2000/2200

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
Content
1.Brief introduction..........
2.Appearance and size·········································································
3.Product structure and working principle················································
Electric control system and accessories
Operating principle of the system
4.Equipment installation·······································································
5.Device function debugging·································································
Control board button description
Function parameter setting
Motherboard wiring instructions
6.Common failure and solution······························································
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
I. equipment introduction
1.1. A brief introduction
Pedestrian gate is intelligent channel management equipment after years
of R&D. The device integrates mechanical, electronic, microprocessor control and
various reading and writing technologies.
The appearance of the equipment adopts stainless steel plate laser
welding molding, beautiful and generous shape, rust-proof, durable, and external
use of standard electrical interface, bar code card, ID card, IC card and other card
readers can be easily integrated in the equipment, to provide civilized and orderly
access for personnel, but also can eliminate illegal personnel access; In addition,
the system is specially designed to meet the fire requirements of the function, in
the case of emergency, to ensure that the passage unimpeded, convenient
personnel timely evacuation;
1.2 functional features
1) with zero self-check function, convenient for users to maintain
and use;
2) illegal entry with alarm function;
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
3) anti-impact function, when no signal is received, the door will
automatically lock or alarm;
4) infrared anti-clamping function;
5) it has the automatic reset function of timeout. After the
pedestrian reads the valid card, if the pedestrian fails to pass
within the specified time, the system will automatically cancel the
pedestrian's permission to pass;
6) unified standard external electrical interface, which can be
connected with a variety of card readers, and can achieve
remote control and management through management
computer.
1.3 Main specification
Frame
material
304 stainless
steel
Input power
AC220±10% V 、
50HZ
Working
voltage
24 V DC
Drive motor
24V dc motor
Working
temp.
-20 ℃-
70 ℃
Relative
humidity
relative humidity
≤90%, no
condensation
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
Opening
signal
Relay dry
contact signal
Communicati
on interface
RS232
Application
Indoor
Traffic speed
30-40 people/min
3. Product structure and working principle
3.1. Mechanical system of pedestrian gate
The mechanical system of gate is divided into two parts: frame
and drive. As a carrier, the frame is equipped with a direction
indicator, a reading and writing device and an infrared sensor.
The main components of the drive are motor, support frame,
transmission shaft, gate.
Drive system
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
.
3.2. Electronic control system of channel gate
The electronic control system consists of card reader, main
control board, infrared sensor, direction indicator board, alarm,
transformer, etc.
Card reader (self-provided) : after reading the information on the
card and judging and processing, send the application pass
signal (switch signal) to the main control board.
◆master control board: the control center of the system, which
receives signals from the card reader and infrared sensor,
makes logical judgment and processing of these signals, and
then issues execution commands to the direction indicator,
motor, counter and alarm.
◆infrared sensor: detect the pedestrian position and play the
role of safety protection.
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
◆direction indicator light: displays the current status of the
channel and guides pedestrians to pass through the channel in a
safe and orderly manner.
◆alarm: when the system detects pedestrians entering the
passage illegally, it will send out an alarm.
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
3.3. Operating principle of the system
◆turn on the power and the system will enter the working state
after 3 seconds.
◆when the card reader reads an effective card, the peal
speaker will make a pleasant sound to remind the pedestrian
that the card is read successfully. At the same time, it will judge
◆
Name
Function
1
Entrance
guard system
IC/ID card access control, fingerprint device,
face recognition, QR code device, gate
opening signal on the control board of gate
machine, remote control, button to open the
door (optional)
2
Control board
The control center of the system, which
receives signals from the card reader and
infrared sensor, and makes logical judgment
and processing of these signals, and then
sends out execution commands to the
direction indicator, motor, counter and alarm
。
3
Infrared
sensor
Detect the position of pedestrians and safety
protection
4
Direction
indicator
Display the current traffic sign status of the
gate and guide pedestrians through the gate
5
Alarm
(speaker)
When the system detects a pedestrian illegally
entering the passageway, it gives an alarm.
6
Motor
Drive the mechanism
7
power supply
Switch
Control panel power supply
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
and process the information read from the card and send an
application signal to the main control board.
◆the main control board receives the signal from the card
reader and infrared sensor, and after comprehensive processing,
sends an effective control signal to the direction indicator and
the motor, so that the direction indicator sign turns into a green
arrow pass sign. At the same time, the brake sends a setting
voice, the main control board controls the motor operation, and
the gate opens to allow pedestrians to pass.
◆after the pedestrian passes through the channel according to
the direction indicator sign, the infrared sensor senses the whole
process of the pedestrian passing through the channel and
continuously sends signals to the main control board until the
pedestrian has passed through the channel completely;
◆if the pedestrian forgets to read the card or reads the invalid
card to enter the channel, the system will forbid the pedestrian to
pass, and will issue a voice alarm, until the pedestrian exits the
channel, the alarm will be lifted; Reread valid chi-square allowed
pass.
Iv. Equipment installation
Attention: During installation and construction, relevant
circuits should be disconnected to ensure that all circuits are
correct before energizing.
4.1 equipment installation instructions
◆prepare the equipment installation tools and check the
accessories according to the packing list.
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
◆after finishing the foundation surface of the installation
equipment, arrange the equipment well.
◆after the hole location is determined, drill the hole and embed
the anchor bolt or expansion bolt of M12.
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
◆put the strong electric cable and weak electric cable
through 3/4 "PVC pipe and bury them in cement to the
corresponding position.
◆open the case door, select one of the equipment as the
reference (it is better to choose the middle one as the reference),
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

([phone]
[phone]
[email protected]
www.TimeWatchindia.com
align the bolt hole of the machine seat with the corresponding
anchor bolt, and tighten the nut first.
◆refer to the wiring diagram, connect the power line and control
line well, and connect the system ground wire protection.
◆After check, if the equipment status is normal, the following
function debugging can be carried out!
◆Check the mains wiring according to the wiring diagram,
check the power wiring and other wiring of the whole equipment
is correct, the debugging can be done after confirmation.
5. Equipment function debugging
5.1 key description
Long press "menu " for 3 seconds -- to enter the L-series, press
"up " enter L-2...
Press "ok" again to enter the H-series , press up or down to
make adjustment , press "menu key" to return and save, and
press "ok" to exit the setting option
Long press "menu key" for 3 seconds -- enter l-1 and press
"down key" plus value d-2...
Press "ok" again to enter the h-series adjustment value "up key -
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020

Follow Us:
www.timewatchindia.com
plus value" "down key - minus value", press "menu key" to return
and save, and press "ok" to exit the setting option
5.2 Function parameter setting
< L-1 >OPENING TIME OF ENTRANCE AND EXIT (DEFAULT 6
SECONDS)
SETTING THE OPENING TIME OF SWINGING DOOR AFTER
SWIPING CARD AUTHORIZATION
< L-2 > SET WORKING METHOD
0: swipe card from left & right
1: left infrared sensor, right swipe the card
2: right infrared sensor, left swipe the card
3: infrared sensor left and right

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
< L-3 > Delay closing time
be set from 0-50s
< L-4 > Left pass voice speaker
default：1：welcome
Voice speaker number code from 0 to 18
For example：0：welcome ，1：welcome back
< L-5 > Right pass voice speaker
default：15：Safe Travel
Voice speaker number code from 0 to 18
For example：0：welcome ，1：welcome back
< L-6 > infrared stack time ( second)
Set the time setting for sensing multiple infrared simultaneously
(default 3/ s)
< L-7 > opening direction when power off
After setting the gate opening direction when power off
Default: 0 to the left , according to the site
Set closing time after pedestrian pass the channel (default: 0.2s), can

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
0：open to the left
1：open to the right
< L-8 > trespassing alarm
default：0：trespassing, please swipe the card
0：trespassing, please swipe the card，
1：ticking sound
< L-9 > Entrance and exit memory function, continuous swipe card
Set up group ticket, continuous swipe mode
default：0: without memory function
0: without memory function, 1：with memory function
< L-10 > Infrared anti-pinch
Set when pedestrians and other circumstances touch off the
anti-clip infrared, swing door will close or not (default: 1 means:
close)
0 represents: open 1 represents:close
< L-11 > Infrared sensor quantity
Default: 0:4 pairs，
0：4 pair 1：6vpair
< L-12 > speaker volume
Set the speaker volume, ( value: 0-15), 0 is min volume, 15 is max volume.

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
Default: 15
< L-13 > voice message test
After entering the voice test, the gate will automatically
broadcast all the voices to make sure all the voice message are
normal and convenient for users to quickly understand which
voice options are included. For example: exit the voice test
mode, please press the "OK" key on the motherboard.
< L-14 > aging test
After entering the aging mode, the gate will automatically open
and close the door and enter the aging mode.
Such as: exit aging mode, please press the menu key.

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
< L-15 > Main motor type selection
Select the corresponding value according to different brands of motors,
the default value is 1, do not change at will.
< L-16 > Main motor type selection
Select the corresponding value according to different brands of motors,
the default value is 1, do not change at will.
< L-17 >Reverse entry gate setting
0 means no close , 1 means close, default value 0, do not change at
will.
< D-1 > Zero setting of closing position
When pedestrian gate close, the channel is not aligned , nor in the middle
position. You can adjust the channel position by enter the parameter setting
according to the voice prompt to manually move the pendulum door to the
desired position, press “ok” to save.
< D-2 > left open position setting
When the gate open not in desired position, You can adjust the channel
position by enter the parameter setting according to the voice prompt to

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
manually move the pendulum door toward the left direction to the desired
position, press ok to save
< D-3 > right open position setting
When the gate open not in desired position, You can adjust the channel
position by enter the parameter setting according to the voice prompt to
manually move the pendulum door toward the right direction to the desired
position, press ok to save
< D-4 > Open speed setting
Set open speed, value from 1-10, 1 is the fastest speed, 10 is slowest
speed.
< D-5 > Gate type
Set type ；swing gate / flap gate, ( 0: swing gate, 1: flap gate). This
parameter is set as factory default. Do not change
< D-6 >The clutch
According to the corresponding drive Settings of brake configuration, "0
is no clutch, 1 : clutch" this parameter is set according to the factory default.
Do not change
< D-7 > Resistance rebound Mode

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
When a pedestrian pass the channel, and hit by the gate, it will
bounce back or keep closing, default setting is 0.
0: Hit the pedestrian then bounce back then keep open1: hit the
pedestrian, stop for seconds, then keep open
< D-8 > counter strength( master)
When the swinging door is in the closed non-working state, the
reverse force can be adjusted when the swinging door is forced open by
the external force. The larger the value, the greater the force ( value 1-20),
default：14
< D-9 > Reset time
Setting the time interval between swiping card 《value 0.1- 10》default：
0.1
< D-10 > buffer strength from gate closing ( master)
The buffer strength is adjusted, The larger the value, the faster the
closing speed and the greater the vibration. The smaller the value, the
slower and more stable the closing speed. Value 50-150 default value: 35
< D-11 > Motor strength( master)
Motor strength setting, the larger the value is, the greater gate closing

(+ 91 )- 11 – 41916615
+ 91 9609749609
sales @ timewatchindia . com
www . TimeWatchindia . com
D-162, Okhla Phase-I, Okhla Industrial Area,
New Delhi,110020
strength and the greater the vibration. Value : 1-100, default is 40.
< D-12 >buffer strength from gate closing ( slave)
The buffer strength is adjusted, The larger the value, the faster the
closing speed and the greater the vibration. The smaller the value, the
slower and more stable the closing speed. Value 50-150 default value: 35
< D-13 > Motor strength( slave)
Motor strength setting, the larger the value is, the greater gate closing
strength and the greater the vibration. Value : 1-100, default is 40.
< D-14 > Power supply
Adjust the power of the main board power "value 1-10" default value: 6
Do not change it at will.
< D-15 > Speed to find zero position
After the gate connected to power, the speed to find the zero speed, the
bigger the value is, the faster the speed, the value is 1-10, default is 5,
don’t change it at will
< D-17 > physical pinch sensitivity
The sensitivity setting when the gate hit pedestrian or in the face of