TIS 875770 User manual
875770 HDBaseT/HDMI/Audio Matrix
Manual
875770 HDBaseT/HDMI/Audio Matrix 8x8
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the life
of your equipment.
SAFTY AND NOTICE
1. The transmission distances of HDMI over UTP cables are measured using
TE CONNECTIVITY 1427071-6. The recommended quality of cable is
AWG 24/1.
2. EIA/TIA-568-B termination (T568B) for CAT cables is recommended for
better performance.
3. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POE OVER-CURRENT
and damage POE components. Please use straight-through CAT cable (both
RJ45 headers are 568A or 568B standard).
4. It is recommended that power up the device after connections of source, sink
and CAT cable.
5. To reduce the interference among the unshielded twisted pairs of wires in
CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables. Shielded CAT cables can be used
to improve EMI problems, which is worsen in long transmission.
6. Because the quality of the CAT cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality,
the actual transmission range is subject to one’s choice of CAT cables.
7. Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS electronics GmbH approved Replacement Part.
Doing so will void the warranty and potentially expose the user to dangerous
voltages resulting in an electrical shock.
8. Do not disassemble the device for any reason. Doing so will void the
manufacturer’s warranty. Also, our unique case is an integral part of the
design of this unit and is responsible for cooling and circuitry shielding. Any
modifications to this case will potentially cause malfunction and product
failure.
9. Do not expose the device to water, moisture, or liquids. Possible electric
shock may result as well as failure of the unit to operate.
875770 HDBaseT/HDMI/Audio Matrix 8x8
Table of Contents
1. Introduction.............................................................................................4
2. Features.....................................................................................................4
3. Panel Descriptions………………………………………….............................5
4. Remote Control Descriptions……................................................................8
5. Application Diagram.....................................................................................9
6. Specifications.............................................................................................10
7. Package Contents......................................................................................11
8. RS-232 Pin Assignment.............................................................................10
9. RS-232 and Telnet Commands .................................................................12
10. GUI control..............................................................................................14
11. Manual setting of input detection of video source……………………………29
12. Maintenance...............................................................................................30
13. Warranty Policy.......................................................................................30
14. Limitations of Warranty............................................................................30
15. Exclusive Remedies.................................................................................31
16.RMA Policy...........................................................................................31
17.Standard Replacement………………………………………………………31
875770 HDBaseT/HDMI/Audio Matrix 8x8
Introduction:
HDBaseT/HDMI/Audio Matrix is a modular design 8x HDMI/HDBaseT and 8x
HDMI and 8x HDBaseT matrix switcher together with 24x8 audio matrix switcher,
supporting 1080p Full HD up to 4K plus all 3D formats, along with multichannel
digital audio formats such as Dolby® True HD and DTS-HD® Master Audio™.
Based on HDBaseT technology, the input or output distance can reach up to
100m via Cat5e/Cat6. Embedded Ethernet switcher provides flexible access to
Ethernet for each zone. Each source can be routed to any display using the
front-panel push buttons, IR remote control, RS-232 interface, or via TCP/IP.
Features:
•2U modular design, flexible input and output cards selection.
•24x8 stereo audio matrix supporting Audio Return Channel.
•HDBaseT chipset inside for input or output distance up to 100m.
•Matrix can power the remote receivers and transmitters, POH (power over
HDBaseT), no power supply needed for the transmitters and receivers. The
maximum number of supplied transmitters and receivers is 8. For
additional devices you have to use the external power supply, which is
delivered with the transmitter-receiver-set. Do not mix with other
manufacturers !
•Supports resolutions up to 1080p@60Hz,4K@30Hz(4:4:4),4K@60Hz(4:2:0)
•Allows any source to be displayed on multiple displays at the same time
•Allows any HDMI display to view any HDMI source at any time
•Dolby TrueHD and DTS-HD master audio pass through HDMI output
•Advanced EDID management for rapid integration of sources and displays
•Front-panel LCD display for status feedback
•Multiple switching mode, push-in button, Windows Software, IR remote
control, RS-232 control, and TCP/IP control
•Easy installation with rack-mounting ears
•Full 3D pass through.
•HDCP compliant
875770 HDBaseT/HDMI/Audio Matrix 8x8
Panel Descriptions
Front Panel
1. LCD display---Show the status of input-output selection, EDID info and so on.
2. IR receiver window----Receive the IR from the remote control of
HDBASET/HDMI/AUDIO MATRIX.
3. Power LED indicator---Indicate the status of the power for the matrix.
4. Power button---Press to power on/off the matrix.
5. HDMI output selection button 1 to 8---Press to select the output from 1 to 8.
6. All button for HDMI outputs---Press to select all of the outputs from 1 to 8.
7. Menu button---Press to enter EDID set mode. Three EDID segments will
display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example:
IN1 1080P 2.0CH, means to set 1080P 2.0CH EDID to INPUT1. The blinking
segment is the one can be changed currently. Segment content items as
below:
875770 HDBaseT/HDMI/Audio Matrix 8x8
INPUT VIDEO AUDIO Note
IN1 1080I 2.0CH.
IN2 1080P 5.1CH
IN3 3D 7.1CH
IN4 4K2K NONE
IN5 D1024 D1024=DVI 1024 x 768
IN6 D1080 D1080=DVI 1920 x 1080
IN7 D1200 D1200=DVI 1920 x 1200
IN8 OUT1 OUT1=Copy OUTPUT1 EDID to INPUTx
ALL OUT2 ALL=Set EDID to ALL INPUTs
OUT2=Copy OUTPUT2 EDID to INPUTx
OUT3 OUT3=Copy OUTPUT3 EDID to INPUTx
OUT4 OUT4=Copy OUTPUT4 EDID to INPUTx
OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx
OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx
OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx
OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx
8. Up selection button--- Press to change segment’s value.
9. ESC---Press to quit EDID set mode.
10. Lock LED indicator---Indicate the status of Lock.
11. Lock button---Press to lock the buttons of the front panel.
12. HDMI input selection button 1 to 8---Press to select the input from 1 to 8.
13. PTP button---Press to mirror all inputs and outputs (e.g. output 1 to input1,
output 2 to input2 and so on).
14. Selection button---Press to select segment to change setting. Selected
segment will be blinking.
15. Down selection button---Press to change segment’s value.
16. Enter button--- Press to set EDID to specified INPUT or copy EDID from
specified OUTPUT to specified INPUT.
875770 HDBaseT/HDMI/Audio Matrix 8x8
Back Panel
1. HDMI inputs 1 to 8 --- Connect HDMI sources
2. HDBT inputs 1 to 8 --- Work with remote HDBT transmitter
3. HDMI outputs 1 to 8--- Output for displays, AVR etc.
4. HDBT outputs 1 to 8--- Work with remote receivers for long distance
transmission.
5. Ethernet--- Connect to the LAN switch for Ethernet access, embedded 1x16
Ethernet switch for remote 8x HDBT transmitter and 8x HDBT receiver
6. RJ45 ---TCP control
7. Power switch--- Power on/off the unit.
8. GND---Connect to ground.
9. RS232 port--- 1x 3-pin phoenix terminal connector
10. L/R In 1 to 8--- 3.5mm stereo phone-jack.
11. IR Out 1 to 8---3.5mm mono phone-jack, connect to IR transmitter cable.
12. Coaxial Output 1 to 8 ---RCA connector.
13. L/R Output 1 to 8 ---3.5mm stereo phone-jack.
14. IR In 1 to 8 ---3.5mm stereo phone-jack, work with control processor.
15. Master RS232---1x 3-pin phoenix terminal connector
16. Global IR Out--- 3.5mm mono phone-jack,
17. Global IR In--- 3.5mm stereo phone-jack.
18. AC power input---100-240V power input.
875770 HDBaseT/HDMI/Audio Matrix 8x8
Remote Control Description
875770 HDBaseT/HDMI/Audio Matrix 8x8
Output and Input select
A. OUTPUT-X select INPUT-Y:
1. Press OUTPUT-X (X means 1 to 8 of outputs)ÆPress INPUT-Y ( Y means
1 to 8 of inputs )
2. Press OUTPUT-X (X means 1 to 8 of outputs)Æpress the left and right
arrow buttons to select the input.
B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTÆPress
INPUT-Y button ( Y means 1 to 8 of inputs ), then INPUT-Y switched toALL
OUTPUTS
C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc):
Press PTP button in Zone OUTPUT
EDID Set Up
A. Fixed EDID to INPUT-Y/ALL
Press 1080I/1080P/3D/4KÆ
Press 2.0CH/5.1CH/7.1CHÆ
INPUT-Y/ALL button in Zone INPUT
B. Copy EDID of OUTPUT-X to INPUT-Y/ALL
Press COPY buttonÆPress OUTPUT-X buttonÆPress INPUT-Y/ALL button
C. User defined EDID to INPUT-Y/ALL
Press USER1/USER2 buttonÆPress INPUT-Y/ALL
NOTE: Pressing button sequence should be finished in 5 seconds, otherwise,
operation discarded.
Application Diagram
Cover page no. 4
875770 HDBaseT/HDMI/Audio Matrix 8x8
Specifications:
Bandwidth：10.2Gbps
Video Input Connectors: 8x HDMI Type A, 8x RJ-45 connector
Video Output Connectors: 8x HDMI Type A, 8x RJ-45 connector
Audio Input Connectors: 8x 3.5mm stereo jack
Audio Output Connectors: 8x 3.5mm stereo jack,8x RCA (SPDIF)
Ethernet Input: 1x RJ-45
RS-232 serial port: 9x 3-pin phoenix terminal connector
TCP/IP Control: 1x RJ-45
IR Input ports: 9x 3.5mm stereo jack
IR Output ports: 9x 3.5mm mono jack
Rack-Mountable: 2 U rack height, rack ears included
Dimensions (W x H x D): 440mm x 358mm x 87mm , without
feet
Shipping Weight: 8.8Kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature : -4°F to 140°F (-20°C to 60°C)
Power Supply: 100V-240V
Package Contents:
1. 1x 875770 HDBaseT/HDMI/Audio Matrix XxX
2. 1x AC power cord
3. 1x Remote control
4. 9x IR Transmitter,
5. 9x IR Receiver.
6. 1x mounting kit.
7. 2x RS232 to Philex Cable
875770 HDBaseT/HDMI/Audio Matrix 8x8
RS-232 Pin Assignment
HDBASET/HDMI/AUDIO
MATRIX Remote Control
Console
PIN
Assignment PIN Assignment
1
NC 1 NC
2
Tx 2 Rx
3
Rx 3 Tx
4
NC 4 NC
5
GND 5 GND
6
NC 6 NC
7
NC 7 NC
8
NC 8 NC
9
NC 9 NC
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
875770 HDBaseT/HDMI/Audio Matrix 8x8
RS232 and Telnet Commands
No.
Command
Action
1
?
Print Help Information
2
HELP
Print Help Information
3
STATUS
Print System Status And Port Status
4
PON
Power On, System Run On Normal State
Reply: Set system power ON, please wait a
moment… Done
5
POFF
Power Off, System Run On Power Save State
Reply: Set system power OFF
6
IR ON/OFF
Set System IR Control On Or Off
7
KEY ON/OFF
Set System KEY Control On Or Off
8
DBG ON/OFF
Set Debug mode on or off
8
LCD ON/OFF
Set LCD always on or Auto Turn Off in power on
state
9
BEEP ON/OFF
Set Onboard Beep On Or Off
10
RESET
Reset System To Default Setting
(Should Type "Yes" To Confirm, "No" To
Discard)
11
MXIR xx FR yy Output
Port IR:xx From Local
IR:yy
xx=[00]: All Output IR, [01...08]: Output IR
yy=[01...08] Local IR
12
MXIR GI (+-)xx Global
IR_IN Signal To
Input/Output IR:xx
xx=[01...08]: Input IR, [09...16]: Local IR
xx=[17...24]: Output IR
+: Add xx To Current Setting
-: Remove xx From Current Setting
13
MXIR GO (+-)xx Global
IR_OUT Signal From
Input/Output IR:xx
xx=[01...08]: Input IR, [09...16]: Local IR
xx=[17...24]: Output IR, [25]: Global IR In
+: Add xx To Current Setting
-: Remove xx From Current Setting
14
MXUART xx TO yy
Local UART:xx Connect
To Input/Output
xx=[01...08]: Local UART, [09]: Global UART
875770 HDBaseT/HDMI/Audio Matrix 8x8
UART:yy
yy=[00]: Disconnect With Any Uart
yy=[01...08]: Input UART, [09...16]: Output
UART
15
MXSTA
Print Matrix IR And UART Connect State
16
AUD TX xx STE yy
Output Port:xx Audio From Input Port:yy Stereo
17
AUD TX xx EXT yy
Output Port:xx Audio From Input Port:yy Extract
18
AUD TX xx ARC tt
Output Port:xx Audio From Output Port:tt ARC
19
AUD TX xx FOSTE
Output Port:xx Audio From Select Video Input Stereo
20
AUD TX xx FOEXT
Output Port:xx Audio From Select Video Extract
21
AUD TX xx DL ss
Set AUDIO:xx Delay zz ms
22
AUD STA
Print Input/Output Port Audio Setting State
xx=[00]: All Output Audio, [01...08]: Output
Audio
yy=[01...08]: Input Port Audio
tt=[01...08]: Output ARC Audio
zz=00 ~ 500ms Delay, 50ms per Step
23
AUD RX xx BPS Input Port:xx Bypass Receive HDMI/DVI Signal
24
AUD RX xx STE Input Port:xx Insert Stereo To HDMI/DVI Signal
25
AUD RX xx AUTO
Input Port:xx Insert Stereo To DVI Signal Only
xx==[00]: All Input Port, [01...08]: Input Port
26
IN xx FO yy
INPUT:xx Force Select Source:yy, Stop Auto Detect
27
IN xx AU yy
INPUT:xx Auto Detect Source, Source:yy High
Priority
xx=[00]: All INPUT Port, [01...08]: INPUT Port
yy=[01]: HDMI, [02]: HDBT
28
OUT xx ON/OFF Set OUTPUT:xx On Or Off
29
OUT xx FR yy
Set OUTPUT:xx From INPUT:yy
Reply: Set output xx connect from input yy
30
OUT xx EH/ET yy
Set OUTPUT:xx Use HDMI/HDBT EDID
xx=[00]: All OUTPUT Port, [01...08]: OUTPUT
Port
yy=[01...08]: INPUT Port
875770 HDBaseT/HDMI/Audio Matrix 8x8
GUI Control
PC System: Microsoft Windows Operation System
Installation
8x8 HDMI Matrix controller is a green software. You just need to copy “8x8
HDMI Matrix Controller vx.x.exe” to the PC which is used to control the Matrix by
RS232 COM or TCP to complete installation.
Preparation
1. Connect PC and Matrix by RS232 cable or UTP cable
2. Power up Matrix (It will take about 5 seconds to be ready with “Di” beep
sound )
3. Double click “8x8 HDMI Matrix Controller vx.x.exe” icon to run it
How to control Matrix
Common information
Click to select tab page
1. COM port or TCP connect status
2. Control command process status
3. Prompt message display area
4. Date and Time display
3241
875770 HDBaseT/HDMI/Audio Matrix 8x8
“General” page
Select control mode: RS232 COM mode (Auto COM ports detected) or TCP
mode
1. List detected COM ports
2. List all Matrix devices after search operation
3. Click to search all Matrix devices that connected in same subnet
4. Click to configuration the selected Matrix’s TCP control configurations
5. Click to connect or disconnect PC and Matrix ( Connection will be
established automatically beforecontrol commands sending )
6. Click to refresh device status: include device information displayed in⑨area
and Input/output port connection status in
⑩
area.
NOTE: Tab pages cannot be changed during control command is processing.
7. To enable or disable Input/output tags displaying when setting buttons on
“Setting” page focused
8. Device information display area
9. Input/output port connection status
2
19
8
7
6
45
3
10
875770 HDBaseT/HDMI/Audio Matrix 8x8
Set TCP control configuration
Click Config button to show TCP configuration window.
1. Set tag to identify Matrix device
2. Set IP mode: Subnet should support DHCP protocol when setAuto IP mode,
then Matrix device will obtain IP automatically. Otherwise, set Static IP mode
and designate a useable IP for Matrix device
3. Set IP address, not editable when Auto IP mode selected. Note: The last IP
BYTE’s range is 2-252.
4. Matrix device MAC address
5. Click OK to set configuration. If configuration is set OK, Matrix devices will be
searched out again
6. Click to Close the window and configuration cancelled
65
4
3
2
1
875770 HDBaseT/HDMI/Audio Matrix 8x8
“Port Tag” page
1. Input port tags
2. Click to edit Input port tags
3. Output port tags
4. Click to edit Output port tags
NOTE: Edit boxes are read only, click “Edit” button to pop up window to edit the
tags.
One set of Input/output port tags can be set for Matrix device when COM control
mode selected.
Input/output port tags can be set for respective Matrix device according to
device’s MAC address.
Edit Input port tags
After action of
②
, edit form will pop-up as below:
42
31
875770 HDBaseT/HDMI/Audio Matrix 8x8
Define tags for respective Input port, then devices connect the Input ports can
be easily remembered.
Click buttons with “×” caption to delete tag which is no use any more, if tag is still
used by any other Input port, delete action will be discarded.
Edit Output port tags
After action of
④
, edit form will pop-up as below:
Define tags for respective Output port, then displays connect the Output ports
can be easily remembered.
Click buttons with “×” caption to delete tag which is no use any more, if tag is still
used by any other Output port, delete action will be discarded.
875770 HDBaseT/HDMI/Audio Matrix 8x8
“Setting” page
1. LED which displays Input number for respective Output port
2. Click to select Input port for respective Output port
3. Click to select previous or next Input port for respective Output port
4. Display Output from Input with tag information when mouse moves over ②
buttons
5. Pre-Setting items: Default is Port to Port
6. Click to edit selected pre-setting item
7. Set selected pre-setting item to Matrix
NOTE: When Change to this “Setting” page, software will try to refresh source
selection status of Output port.
6
7
5
4
1
3
2
875770 HDBaseT/HDMI/Audio Matrix 8x8
Pop-up tag messages
When “Display Input, Output tags when focus setting buttons” checkbox on
“General” page is checked and Input/output port tag has been defined, tag
messages will pop up like as:
Table of contents
