CYP PU-442PL-KIT User manual

PU-442PL-KIT
4 x 4 HDBaseT™ Lite Matrix with PoE, plus 2 Additional
Independent HDMI Zone Outputs (total 4 x 6 Matrix)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 16/12/2013 First release
v1.01 17/12/2013 Corrected description/features
v1.02 13/01/2014 Added new image/description

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 Side Panel...................................................10
6.4 Remote Control........................................10
6.5 IR Pin Assignment....................................11
6.6 RS-232 Protocols......................................11
6.7 RS-232 & Telnet Commands.................12
6.8 Telnet Control............................................14
6.9 Web GUI Control ......................................16
7. Connection Diagram .......................... 18
8. Specications...................................... 19
9. Acronyms............................................. 20

6
1. INTRODUCTION
This 4 by 6 HDBaseT™ Lite Matrix utilises four HDMI inputs and four
HDBaseT outputs over a single CAT5e/6/7 cable (up to 60m) for
each output, plus two additional HDMI outputs. All six outputs are
independent allowing any source to be distributed to any output. The
HDBaseT outputs feature Power over Ethernet (PoE) functionality and
allow the user to power the supplied PU-515PL-RX receivers without the
need for a separate mains power supply.
The PU-442PL-KIT supports the transmission of video (resolutions up to
1080p Full HD and 1920x1200@60Hz), PoE, 2-way IR, multi-channel digital
audio, and control via IR, RS-232, or Web GUI/Telnet IP. Use the IP control
feature to enable users to access and control the matrix remotely and also
allow additional options for integration of third-party control systems.
2. APPLICATIONS
HDMI system controls
Video/TV wall display and control
Security surveillance and control
Commercial advertising, displaying and control
Lecture room display and control
3. PACKAGE CONTENTS
4 by 6 HDMI HDBaseT Lite Matrix
4×PU-515PL-RX receivers
5×IR Receiver
5×IR Emitter
1×24V/3.75A DC Power Supply
1×Remote Control
1×Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment with HDMI connection cables
Certied CAT5e/6/7 cables
Output displays or audio receiver equipment with HDMI connection
cables

7
5. FEATURES
Supports all v1.3 HDMI resolutions
Supports uncompressed video/audio up to 10.2Gbps
Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,
1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA.
HDMI, HDCP and DVI complaint
High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio plus LPCM (up to 192kHz)
Uncompressed data transfer over single CAT cable (60m - CAT5e/6/7)
Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit.
Supports RS-232, 2-Way IR, Manual Selection Buttons, and HDMI CEC
control pass through
Selectable EDID settings - TV (downstream) and STD (xed)
Compact 1U Rack mount design
Supports 3D signals
Supports additional IR Control via a master (ALL) Input/Output
Supports full IP control
Supplied with 4x PU-515PL-RX receivers

8
6. OPERATION CONTROLS AND FUNCTIONS
The following sections describe the hardware components of the unit.
6.1 Front Panel
POWER LOCK MENU
OUT
B2
A1C3
D4IN
FE
1 2 3 4 5 6
1LCM: This monitor displays your setting information with each input
and output selection.
2IR: This IR window accepts the remote control signal of this device
only.
3Power Button & LED: Press this button to turn ON the device and
the green LED will illuminate when the power is ON. When the LED
illuminate in red it is in standby mode.
4LOCK: Press this button to lock all the buttons on the panel and the
LED will illuminate. To unlock, just press it again.
5Menu: Press this button once to select EDID setting from STD(internal)
1 or TV(external) 2 then press it again to conrm the selection. Press
this button every time to conrm the selection.
61~4/A~F & OUT/IN button: Press OUT/IN button rst to select the
output/input then press the number button to make the selection
accordingly. For example, output A~B wish to select input 1 and C~E
wish to select input 2. Press OUT→A→IN→1→Menu, and then press
Out→C→D→E→In→2→Menu. If the menu button is not pressed the
selection will not be changed.

9
6.2 Rear Panel
SERVICE
RS-232
CONTROL
B CA E FD
DC 24V
1
2
3
4
GND
GND GND
IR OUT
IR IN
ALL
V+
V+
1
IR IN IR OUT
2
IR IN IR OUT
3
IR IN IR OUT
4
IR IN IR OUT
HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4
HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT
HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT
2 3 4 45 5 5 10 115 6
1
7
8
7
8
7
8
7
8 9
1RS-232: This slot is to connect with D-Sub 9pin cable from the PC/
Laptop device for RS232 control.
Note: This RS-232 obtain routable function that is, from the Matrix it can
send commands to all receivers or from receiver sides it can also send
commands to control the Matrix. In order to allow the receivers to send
command to control the Matrix, a null modern cable/adaptor is required.
In order to allow the receivers to send command to control the Matrix, a
null modern cable/adaptor is required.
2CONTROL: This port is for Telnet and Web GUI control. Connect and
active network system with RJ45 terminated cable (for details, please
refers to section RS-232 & Telnet commands and Web GUI Control).
Warning: Please do not connect this port directly to the PC/Laptop as the
Telnet function will not work.
3Service: This slot is to connect with mini USB B type cable for rmware
update only.
4HDMI OUT A/E: These slots are to connect with HD TV/display for
instant display.
5CAT5e/6/7 OUT B/C/D/F: These slots are to connect with HDMI over
CAT5e/6/7 Receiver for signal extension up to 60m.
6HDMI IN 1~4: These slots are to connect to input source equipment
such as DVD player or Set-Top-Box with HDMI cable or DVI to HDMI
converter cable for input signal sending.
7IR IN 1~4: These slots are to connect with IR Receiver included in the
package for IR signal receiving.
8IR OUT 1~4: These slots are to connect with IR Emitter included in the
package for IR signal sending.
9ALL IR OUT: This slot is to connect with the IR Emitter for IR signal
received from receiver sides and send to the source side.

10
10 ALL IR IN: This slot is to connect with the IR receiver for IR signal
receiving and send out to receiver sides.
11 DC24V: This slot is to plug the power cord with adaptor included in
the package and then connect them with AC wall outlet for power
supply.
6.3 Side Panel
1
1Ventilator: These are fan ventilation areas, DO NOT block or cover
with any object.
6.4 Remote Control
1Power: Press this button to
switch ON the device or set it to
standby mode.
2IN: Input ports selection 1~4.
3OUT: Output ports selection A~F.
H
8
1A
B
2
C
3
4D
5E
6F
7G
CR-110
IN OUT
3
1
2