SIIG AV-GM0703-S1 User manual

16x16 3G/HD/SD-SDI Matrix
P/N: AV-GM0703-S1

Safety and Notice
The AV-GM0703-S1 16x16 3G/HD/SD-SDI Matrix has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all
electronic equipments, the AV-GM0703-S1 should be used with care. Please read and follow the
safety instructions to protect yourself from possible injury and to minimize the risk of damage to the
unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
TABLE OF CONTENTS
INTRODUCTION................................................................................................................ 1
FEATURES ........................................................................................................................ 1
PACKAGE CONTENTS...................................................................................................... 1
SPECIFICATIONS.............................................................................................................. 2
PANEL DESCRIPTIONS.................................................................................................... 3
CONNECTION DIAGRAM.................................................................................................. 4
HARDWARE INSTALLATION ............................................................................................ 4
OPERATION APPROACH.................................................................................................. 5
LIMITED WARRANTY........................................................................................................ 9

1
INTRODUCTION
The AV-GM0703-S1 16x16 3G/HD/SD-SDI Matrix provides the most flexible and cost
effective solution in the market to route 3Gbps high definition video sources from any of
the sixteen SDI sources to the any eight SDI receivers at the same time. This solution is well
suited for use in home theater, conference room presentation systems, or other similar
setting or application.
FEATURES
●Inputs meet SMPTE 259M, 292M, 424M, 425M
●Allows any SDI display to view any SDI source at any time
●Auto-Reclocking
●The matrix master can switch every output channels to any SDI inputs by push-in button,
IR remote controller or RS-232 control
●Easy installation with rack-mounting and wall-mounting designs for master and receiver
respectively
PACKAGE CONTENTS
●1x AV-GM0703-S1 ●1x UL AC C13 power cord
●1x BNC Terminator Plug ●1x IR Remote control
●1x Rack-mounting ear set ●1x User Manual
●1x Installation software CD

2
SPECIFICATIONS
Model Name
AV-GM0703-S1
Technical
Role of usage
True 16x16 matrix
Video bandwidth
2.97 & 2.97/1.001Gbps
Video support
[3G] 1080p@50/59.94/60 (4:2:2)
[HD] 720p50/59.94/60, 1080p24/30, 1035i50/59.94/60,
1080i50/59.94/60
[SD] [email protected], PAL@50Hz
Audio support
Yes
Cable equalization
[3G] up to 100m(300ft) / [HD-SDI] up to 150m (500ft) / [SD-SDI] up
to 300m (1000ft)
Reclocking function
Yes
PCB stack-up
4-layer board [impedance control —differential 100; single 50]
Input
16x SDI BNC + 1x Synchronized BNC + 1x RS-232
Output
16x SDI BNC + 1x Synchronized BNC loop-out
SDI Input selection
Push button / IR remote / RS-232
IR remote control
Electro-optical characteristics: = 25/ Carrier frequency: 38kHz
RS-232 connector
DE-9 [9-pin D-sub female]
Mechanical
Housing
Metal case
Dimension
s
[L x W x H]
Model
440 x 280 x 42mm [1’5” x 0.9” x 1.3”]
Package
513 x 456 x 144mm [1’7” x 1’5” x 5.6”]
Carton
535 x 320 x 495mm [1’8” x 1’ x 1’6”]
Weight
Model
4051g [8.9 lbs]
Package
4900g [10.8 lbs]
Fixedness
Interlocking power supply
Power supply
AC Power 100-240V
Power consumption
35 Watts [max]
Operation
temperature
0~40C [32~104F]
Storage temperature
-20~60C [-4~140F]
Relative humidity
20~90% RH [no condensation]

3
PANEL DESCRIPTIONS
Front Panel
1. Power Switch: Power ON/OFF switch
2. Output Push Buttons & 7-segment LED Indicators: Front panel push buttons used to
select the number of display channel & LED display for output ports
3. Input Push Buttons & 7-segment LED Indicators: Front panel push buttons used to select
the number of input source & LED display for input channels
4. IR sensor: IR sensor for receiving the IR commands from IR remote
Rear Panel
5. RS-232: RS-232 control port
6. Digital I/O: Control signal
7. INPUT PORT 1 –16: SDI inputs
8. OUPUT PORT 1–16: SDI outputs
9. AC Power: 100-240V

4
CONNECTION DIAGRAM
HARDWARE INSTALLATION
AV-GM0703-S1
1. Connect all sources to SDI Inputs on the 16x16 SDI matrix
2. Connect all outputs to SDI Receiver
3. Connect the AC power supply to the 16x16 SDI matrix
4. Power on the 16x16 SDI matrix AV-GM0703-S1

5
OPERATION APPROACH
Method A: Push-in Button
IN/OUT Mapping
(1) Use the “+” or “-” output push button to select the number of display
(2) Use the “+” or “-” input push button to select the number of input source
“+”: change selected input/output port in ascending order
“-”: change selected input/output port in descending order
After few seconds, the setting will be active.
Method B: IR Remote Control
Button
Function
ON
Mute off the video output
OFF
Mute the video output
F1, F2, F3, F4
Reserved Buttons
Route input to
output
output port number + To + input port number +
Take
Select I/O 10, choose
Select I/O 11-16, choose + (1-6)
Preset
Mapping
Number + Preset + Take
[Memory 6 sets of configuration]
Save Mapping
Number + Save + Take
[Memory 6 sets of configuration]
ALL
Input Port number + To + All output port + Take
STATUS
Output port number + Status + Take
CLEAR
Clear the remote setting
Mute
Output port number + Mute + Take

6
Method C: Software Control through RS-232 port
System Requirements and Precautions
1. Whenever power off AV-GM0703-S1, please stay unpowered at least 5 to 10 seconds to
allow power capacitors to discharge.
2. The AV-GM0703-S1 provides software control program under Microsoft Windows XP, 7, 8
through the interface of RS-232 control port
3. Before you click on the icon of the software, make sure you have secured the
connection between your computer RS-232 port and the AV-GM0703-S1.
Start the software control program
When clicking on the executable file, the following dialog will pop-up (under Microsoft
Windows 7, please run as administrator).
Control Interface
1. Info
Read the software version.
2. COM Port selection
Use RS-232 cable to connect the port on device and computer. Select correct COM port
and click the button.
1
2
3
4
5
7
6

7
3. Connection Status
Show the connect status (Connected or Disconnected).
4. In/Out switch panel
For each output, you can assign arbitrary video source or mute output video here.
5. Firmware Update
The “Firmware update” window shows up as below. Before firmware update process,
please ensure your RS-232 cable is connecting and the status is “CONNECTED”.
Click button to select the firmware file which you want to update.
Click button.
Recycle power.
Click button and the firmware will start to update.
6. Mapping
Save/Recall the Mapping Configuration. In this part, you can rename the mapping, save
the current mapping or recall previous saved mapping.

8
7. Default Reset
To do factory default reset. This default reset process will take about 10 seconds.
Method D: Terminal control:
Baud rate: 9600
Data length: 8bit
Parity check: No
Stop bit: 1
Command Set:
COMMAND
ACTION
ST + 0x0d
Show all mapping
PON + 0x0d
Power on the device
POFF + 0x0d
Power off the device
MUTE + number (ASCII) + 0x0d
Mute output video
VR + 0x0d
Show the firmware version
P + number (ASCII) + I + number (ASCII) +
0x0d
Switch I/O mapping
SMAP + number (ASCII) + 0x0d
Save mapping
LMAP + number (ASCII) + 0x0d
Recall mapping
WHO + 0x0d
Show the model no.
FSET## + 0x0d
Factory reset