TLS Electronics QuickControl XL User manual

TLS electronics GmbH
Tel.: [phone] - 0
Marie-Curie-Straße 20
Fax: [phone] - 90
D –40721 Hilden
e-mail: [e-mail]
QuickControl XL
Installation and user manual
Ident. Nr.: 8705663

Installation and user manual
2 Stand 09/17
Content
C 1 Allgemeine Informationen ............................................................3
C 2 Bestimmungsgemäße Verwendung und Einsatz.........................7
C 3 Geräteansicht/Gehäuse ...............................................................8
C 4 Montage/Verkabelung................................................................11
C 5 Inbetriebnahme ..........................................................................16
C 6 Bedienung..................................................................................50
C 10 Optionen...................................................................................51
C 11 Pflege, Wartung, Entsorgung, Support ....................................54
C 12 FAQ..........................................................................................55
C 13 Anschlussplan und Diagramme ...............................................57
E
G
B

Installation and user manual
Stand 09/17 3
C 1 General Information
C 1.1 Identification
Manufacturer: ..................................................... TLS electronics GmbH
Marie-Curie-Straße 20
D-40721 Hilden
Tel: [phone]
email: [e-mail]
Product:....................................................................... QuickControl XL
Version:.............................................................................................1.0
Installation and user manual:..............................................State 09/17
These operating instructions are a part of this product. They contain
important notes on handling the device. Please remember this also if
you pass on the device to third parties. Keep these operating
instructions for further reference.
Imprint
This operating instructions are published by TLS Communication
GmbH. All rights, including translation, reserved. Reproduction of any
kind, e.g. photocopies, microfilms or capturing through electronic data
processing equipment requires written approval by the publisher.
Reprint, also in part, is prohibited. These operating instructions reflect
the technical status at the time of going to press. Technological and
design changes are reserved.

Installation and user manual
4 Stand 09/17
C 1.2 Scope of delivery
QuickControl XL Ident. Nr.:
1x QuickControl XL..................................................................8640045
1x Infrared emitter single .......................................................8705445
1x Mains adaptor 5V/1000mA .................................................8706599
1x Screwdriver.........................................................................8705602
1x Cable USB 1m Am/BMini5m ..............................................8705594
Optional:
Adaptor (installation version) ..................................................8640024
C 1.3 Technical Data
External power supply: ................... 230 VAC, 50 Hz auf 7,0 VDC,
.................................................................................................0,5 A
Switching outputs max:................................................30V / 300mA
Connections:........................................2 x 9 pin Wago Klemmleiste
Inputs:.............................................................1 x Schlüsselschalter
........................................................................2 x externe Eingänge
Outputs ...................................................................................2 x IR
..............................................................................4 x Schaltkontakt
............................................................ 1 x Schaltkontakt GreenLine
.........................................................................................1 x RS232
Weight:.......................................................................................96 g
Dimensions (D/H/W):.............................................81 x 26 x 81 mm
C 1.3.1 PC System requirements
PC with INTEL® based or compatible Processor
256 MB RAM
50 MB available hard disc
Graphics card Minimum resolution 1024x768 Pixel
From Windows XP
Microsoft ® .NET Framework from Version 2.0
C 1.4 Environmental conditions
Operating temperature:............................................+5°C bis +40°C

Installation and user manual
Stand 09/17 5
Rel. humidity:....................................................................Max. 85%
Atmospheric pressure:.........................................600 bis 1000 hPA
C 1.5 In case of damage in transport
In case of transport damage, please observe the following:
Do not change the goods and the packaging in any way.
Let the deliverer sign for the damage.
Do not use the damaged device.
In case of delivery by a forwarding agent or parcel service,
please notify us of the damage telephonically or in writing
within 5 calender days.
Do not return the device without prior consultation!
Please note that we only accept returned goods if agreed to
accept the return in advance.
Non-compliance with these regulations invalidates any claim
for compensation!
The following regulations and safety notes regarding installation
and maintenance must be observed:
C 1.6 Standards and regulations
VDE 0100 Regulations for erection of power installations for rated
voltages below 1000V.
VDE 0105 Operating power installations, general stipulations.
EN 60335-1 Safety of household and similar electrical appliances.
C 1.7 General safety notes

Installation and user manual
6 Stand 09/17
This operating instructions contains basic notes to be observed when
operating TLS QuickControl XL. Follow the instructions closely to
avoid errors. It is therefore imperative to read these operating
instructions before working with TLS QuickControl XL.
The safety notes contained in these instructions that result in hazards
to persons unless observed, are indicated by the
Safety symbol in acc. With DIN 4844-W8 and the word “Danger”.
Work on electrical components or component groups may only be
performed by a qualified electrician in acc. with electrical regulations
(e.g. EN 60204, DIN VDE 0100/0113/0160).
Plug connections and cables may be destroyed. Connect plugs and
sockets without using force. Do not kink cables when laying; lay with
an adequate radius (R>5 x cable diameter).
Screws, bolts and threads may be damaged. Use suitable tools to
loosen screws and bolts.
Use device indoors only, i.e. not in open air. Never expose the device
to moisture!
C 1.8 Assembly notes

Installation and user manual
Stand 09/17 7
Danger
Before starting any work, unplug all devices / equipment / areas and
secure against accidental re-connection.
C 1.9 Warranty
TLS warranty for TLS QuickControl XL is 36 months. Damages
arising from improper operation or through use of force are not
covered by this warranty. The warranty is invalidated if unauthorised
persons open the device.
C 1.10 Safety
Danger
Voltage and current fluctuations when connecting the TLS
QuickControl XL may damage electronic components. Connect all
inputs and outputs before connecting the power supply.
Danger
Allow technical staff only to connect the device. (e.g. EN 60204, DIN
VDE 0100/0113/0160)
Danger
Electrical shocks from the power supply units may be fatal or lead to
grave injury to health. Never open the housing of the TLS
QuickControl XL.
C 2 Application area and intended use

Installation and user manual
8 Stand 09/17
TLS QuickControl XL is a multifunctional room control system for
small and mid-size conference rooms. QuickControl XL trasmits
control commands over long distances via IR commands and RS232
protocols to playback and display devices and controls via I/O
contacts connected screens, ceiling lifts and similar media techno-
logial devices.
QuickControl XL can be mounted space-saving in wall or integrated
in every table installation module. With each button at QuickControl
XL 8 functions can be executed simultaneously. With 8 internal and 2
optionally connectable external buttons a total of up to 80 functions
can be executed in that way.
The labelling of QuickControl XL can be done according to
individual needs.
QuickControl XL can be easily configurated via itsConfiguration
Tool,
The integrated GreenLine function of QuickControl XL diconnects
automatically all connected devices after the presentation from the
230 V~/110 V~ mains and puts all devices back into their initial state.
Thus this room control system helps to save energy costs and to
extend the devices’ life cycle.
C 3 View of device/Housing

Installation and user manual
Stand 09/17 9
C 3.1 Front view, operating mode
Sketch 1
C 3.2 Front view
Sketch 2
The transparent plastic cover for the inscription area is engaged at
the top and bottom. Using the miniature screwdriver, the cover
Mechanical
installation lock
PC output
Infrared receiver
Dip switch

Installation and user manual
10 Stand 09/17
can be loosened at the recess. The mechanical installation lock
and the PC connection, operating mode switch and infrared
learning eye can now be used.
C 3.3 Button numbering
Sketch 3
C 3.4 Rear view with cable terminal strips
Two 9-pole terminal strips X1 and X2 are located at the back of
QuickControl. The mains adaptor, 2 infrared emitters, 4 relays and
the mechanical installation lock can be connected to these terminal
strips (key switch to lock the keypad against unauthorised users).
Sketch 4

Installation and user manual
Stand 09/17 11
Connections terminal strips X1:
1Power supply +7,5 Volt
2Power supply Ground
3Infrared-output 1
4Ground
5Infrared-output 2
6 Ground
7RS232 output
8Ground
9 Input key switch
Connections terminal strips X2:
1Power supply +7,5V
(e. g. for power supply Relay box)
2Output 1 (Relay)
3 Output 2 (Relay)
4Output 3 (Relay)
5 Output 4 (Relay)
6Output 5 (GreenLine function)
7External input 2
8 External input 1
9Ground
C 4 Device installation/Cabling
Lever locking housing
X1
X2

Installation and user manual
12 Stand 09/17
C 4.1 Installation QuickControl XL
Sketch 5
Mount the carrier frame in the correct position on a flush socket
output or trunking (observe TOP).
Push the cover frame onto the carrier frame
Connect QuickControl to your end devices (refer C 4.2 and C
4.4)
Plug the key sensor onto the carrier frame
An installation lock can be activated to prevent disassembly is
available (refer C 3.2 Figure 2)
C 4.2 Cabling QuickControl XL

Installation and user manual
Stand 09/17 13
Press the mounting pins down with a screwdriver (refer C 3.3 Figure
3). This opens the cable terminal underneath. Then insert the
connecting cable of the mains adaptor, infrared receiver, relay etc.
into the opening. Release the mounting pins and the connecting
cable is fastened.
C 4.3 AC adaptor connection
Connect the AC adaptor cable to terminals 1 and 2 (Power + GND) of
the terminal strip X1 (refer C 4.2 Figure 5). The positive supply
voltage is connected to terminal 1 and the earth lead to terminal 2.
Sketch 6
X1
Ensure that the white marked cable of the mains adaptor is
connected to the Power terminal.
C 4.4 AC adaptor extension
1 Power
2 GND
3 IR1
4 GND
5 IR2
6 GND
7 TxD
8 GND
9 IN-SS

Installation and user manual
14 Stand 09/17
Sketch 7
If you need an extension for the mains adaptor, a 2-pole cable with
plug and socket is available (item no. 8640033). Push the socket onto
the 2-pole cable of the mains adaptor. Push the plug onto the
extension cable and connect the cable to Power and GND of terminal
X1 (refer Figure 6).
C 4.5 Infrared emitter connection
The infrared emitters are connected to terminal strip X1 on terminals
3 and 4 (or 5 and 6). Ensure correct polarity of the transmitting
diodes.
The red marked cable of the IR emitter is always connected to
terminals IR1 or IR2. The coppery cable of the IR emitter is
connected to the terminal GND.
The IR emitter is sticked directly to the IR receiver of the end device.
C 4.5.1 Connection options IR emitter
Up to two IR emitters can be connected per output.
For this you can have from TLS one single IR emitter (Ident.-No. 864
0027) and/or a double IR emitter (Ident.-No. 864 0028).
These can be combined with each other, in which the maximum
number of IR emitters per output must not be exceeded.
1
2
3
4
5
6
7
8
9
Power
GND
GND
IR1
IR2
GND
-----
-----
GND
8640033 Power cable - OL
X1
8705567
Female 2pin,
for clamping
8705568
Male 2pin,
for screwing
ACadaptor
AC adaptor Extension cable
GND - brown wire
black/black-white wire - white wire
1 Power
2 GND
3 IR1
4 GND
5 IR2
6 GND
7 TxD
8 GND
9 IN-SS
X1
The AC adaptor has to be connected to
terminals 1 und 2 of the terminal strip
X1. Please note the right polarity of the
AC adaptor. Brown wire to terminal
GND. White wire to terminal Power.
AC adaptor
GND
black/black white wire
Extension cable
- brown wire
- white wire
8640033 Power cable OL

Installation and user manual
Stand 09/17 15
C 4.5.2 Connection examples IR emitter
2 x IR Emitter single:
Here you can connect 2 single IR emitters for IR controllable devices
to each output. The IR emitters are connected respectively to the
terminals 3, 4 (IR1 + GND) as well as 5, 6 (IR2 + GND).
3 x IR Emitter single:
Here you can connect 2 single IR emitters to one output. These are
connected to the terminals 5 and 6 (IR2 + GND).
Connect one more emitter to the terminals 3 and 4 (IR1 + GND).
1 x IR emitter single and 1 x IR emitter double:
Here you can connect 1 single IR emitter and 1 double IR emitter to
one output each. The single IR emitter is connected to the terminals
3, 4 (IR1 + GND), whilst the double IR emitter is connected to 5, 6
(IR2 + GND).
Sketch 8
C
4.5.3 Infrarot Verlängerung
1
2
3
4
5
6
7
8
9
Anschlussmöglichkeiten IREmitter
2x 8640027, IR Emitter einfach 3x 8640027, IR Emitter einfach
1x 8640027, IR Emitter einfach
1x 8640028, IR Emitter zweifach
PWR
GND
GND
GND
GND
IN SS
TxD
IR 2
IR 1
1
2
3
4
5
6
7
8
9
PWR
GND
GND
GND
GND
IN SS
TxD
IR 2
IR 1
1
2
3
4
5
6
7
8
9
PWR
GND
GND
GND
GND
IN SS
TxD
IR 2
IR 1
X1 X1
X1

Installation and user manual
16 Stand 09/17
Sofern Sie eine Verlängerung für das Infrarotkabel benötigen,
erhalten Sie bei TLS unter der Ident-No. 864 0018 ein zweipoliges
Kabel mit Stecker und Buchse. Das Kabel des Infrarot-Senders wird
mit der Klemmvorrichtung der Buchse verbunden.
Anschließend wird die Buchse mit dem Verlängerungskabel
zusammengeschlossen. Das andere Ende des Kabel wird an den
Anschlüssen IR1 und GND oder IR2 und GND der Klemme X1
angebracht (siehe C 4.5.3 Skizze 9).
Skizze 9
C 5 Inbetriebnahme
1
2
3
4
5
6
7
8
9
PWR
GND
GND
GND
GND
INSS
TxD
IR2
IR1
8640019 IR Sendekabel ÜL
rot oder blau
Schirm
Kupfer
8705567
Buchse 2 polig,
zumeinklemmen
8705568
Stecker 2 polig,
zumfestschrauben
IR Sender Verlängerungskabel
SchirmKupfer - brauneAder
rote / blaueAder - weißeAder
Infrarot Sender weiß
braun

Installation and user manual
Stand 09/17 17
C 5.1 Installation Configurations Tool
Installation des Configuration Tools auf Ihrem PC
Mit der QuickControl XL werden eine CD und ein TLS USB-
Verbindungskabel mitgeliefert.
1. Legen Sie die Tool-CD in das CD-ROM-Laufwerk Ihres
Computers ein. Bitte beachten Sie, dass das Tool nur unter
Windows, und zwar ab der Version XP, lauffähig ist.
2. Die CD startet automatisch und der Installation Manager
erscheint. Sollte dies nicht der Fall sein, starten Sie die CD
manuell.
Skizze 10
Installations-Manager
Auf der Oberfläche des Installation Managers haben Sie die
Möglichkeit, das Programm je nach Gerät zu installieren bzw. zu
deinstallieren sowie das Handbuch (Manual) einzusehen.

Installation and user manual
18 Stand 09/17
Um das Installationsprogramm des Configuration Tools zu starten,
klicken Sie auf den Install software Button. Folgen Sie den
Anweisungen des Installationsprogramms.
Das Programm benötigt für den Betrieb die System Utilities-Software
.NET Framework von Microsoft. Sollte diese nicht auf Ihrem Rechner
installiert sein, haben Sie zwei Optionen, die Software nachträglich
zu installieren. Sie können entweder auf die Installationsdatei im
Installationsverzeichnis zurückgreifen oder die Software kostenlos
auf der Webseite der Firma Microsoft ® herunterladen.
Installieren des .NET Frameworks von der CD
Starten Sie den Explorer auf Ihrem PC und navigieren Sie in den CD-
Ordner dotnet. Starten Sie die Datei dotnetfx.exe.
Anschluss der QuickControl XL mit dem PC
1. Verbinden Sie mittels USB-Verbindungskabel die QuickControl
XL-Steuerung mit Ihrem PC. Der Anschluss für das Kabel
befindet sich unter dem Beschriftungsfeld. Um dieses zu
entfernen, hebeln Sie vorsichtig die durchsichtige
Kunststoffabdeckung ab und entfernen Sie das
Beschriftungsfeld.
2. Stecken Sie das andere Ende des Verbindungskabels in einen
freien USB Port Ihres PCs.
Das Betriebssystem erkennt nun automatisch das neu
angeschlossene Gerät und fragt nach einem erforderlichen Treiber.
Die Treiber befinden sich im Installationsverzeichnis des
Configuration Tools. Standardmäßig befindet sich der Ordner mit
dem Treiber auf Ihrem Laufwerk unter Programme/TLS/QuickControl
XL configuration tool/treiber. Geben Sie dem Betriebssystem diesen
Pfad an, um den Treiber zu installieren.
Nach der erfolgreichen Installation des Treibers starten Sie das
QuickControl XL Configuration Tool.

Installation and user manual
Stand 09/17 19
Es erscheint folgende Bildschirmoberfläche:
Skizze 11
Configuration tool
Das Tool dient der Anpassung der Konfiguration der QuickControl XL
auf Ihre individuellen Bedürfnisse.
C 5.2 Konfiguration

Installation and user manual
20 Stand 09/17
C 5.2.1 Home (Start)-Seite
Um das Configuration Tool zu starten, klicken Sie auf das Icon auf
Ihrem Desktop. Die erste Seite (Start-Seite) des Configuration Tools
zeigt die Nummerierung der Tasten der QuickControl XL sowie am
oberen Bildschirmabschnitt eine Menüleiste für diverse Funktions-
Einstellungen.
Skizze 12
Menüleiste
Links oberhalb der Menüleiste befinden sich vier Schnellzugriff-Icons
für die gängigsten Funktionen (Neues Projekt, Projekt öffnen, Projekt
speichern und Startseite anzeigen)
Im unteren Bereich des Konfigurations-Tools befindet sich eine Info-
Leiste.
Sie gibt Auskunft über den Gerätestatus, die Serien-Nummer, die
USB-Verbindung (communication status) und die Firmware.
Zudem zeigt die Info-Leiste die zuletzt getätigte Aktion an.
Funktionsgruppe Projekt:
In der Funktionsgruppe Projekt haben Sie die Option, ein neues
Projekt zu erstellen, zu speichern oder ein vorhandenes Projekt zu
öffnen.
Skizze 13