TLS Electronics 875760 User manual
875760 HDbaseT/HDMI/Audio Matrix 4x4
Manual
875760 HDBaseT/HDMI/Audio Matrix 4x4
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjust-
ing this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the life
of your equipment.
SAFETY AND NOTICE
1. The transmission distances of HDMI over UTP cables are measured using
TE CONNECTIVITY 1427071-6
2. EIA/TIA-568-B termination (T568B) and “AWG24/1 solid wire” for CAT
cables is recommended for best performance.
3. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POE OVER-CURRENT
and damage POE components. Please use straight-through CAT cable (both
RJ45 headers are 568A or 568B standard).
4. It is recommended that power up the device after connections of source, sink
and CAT cable.
5. To reduce the interference among the unshielded twisted pairs of wires in
CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables. Shielded CAT cables can be used
to improve EMI problems, which is worsen in long transmission.
6. Because the quality of the CAT cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality,
the actual transmission range is subject to one’s choice of CAT cables.
7. Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS electronics GmbH approved Replacement Part.
Doing so will void the warranty and potentially expose the user to
dangerous voltages resulting in an electrical shock.
8. Do not disassemble the device for any reason. Doing so will void the manu-
facturer’s warranty. Also, our unique case is an integral part of the design of
this unit and is responsible for cooling and circuitry shielding. Any modifica-
tions to this case will potentially cause malfunction and product failure.
9. Do not expose the device to water, moisture, or liquids. Possible electric
shock may result as well as failure of the unit to operate.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Table of Contents
1. Introduction.............................................................................................5
2. Features.....................................................................................................5
3. Panel Descriptions.......................................................................................6
4. Remote Control Descriptions......................................................................10
5. Specifications...............................................................................11
6. Application Diagram...........................................................................12
7. Package Contents......................................................................................13
8. RS-232 Pin Assignment.......................................................................13
9. RS-232 and Telnet Commands ...............................................................14
10. GUI control..............................................................................................16
11. Maintenance..............................................................................................27
12. Warranty Policy...................................................................................27
13. Limitations of Warranty........................................................................27
14. Exclusive Remedies...........................................................................28
15. RMA Policy...........................................................................................28
875760 HDBaseT/HDMI/Audio Matrix 4x4
Introduction:
The HDBaseT/HDMI/Audio Matrix 4x4 routes four Hi-Def sources to any four
HDTV displays, supporting 1080p Full HD up to 4K@30Hz UHD plus all 3D
formats, along with multichannel digital audio formats such as Dolby® True HD
and DTS-HD® Master Audio™. Embedded audio extractors can extract the
audio and output via L/R or Coaxial. Volume can be controlled for analogue
audio out. Based on HDBaseT Lite chipset inside, the output distance can reach
up to 70m via Cat5e/Cat6. Each source can be routed to any display using the
front-panel push buttons, IR remote control, RS-232 interface, or via TCP/IP.
Features:
•HDCP 2.2 compliant
•Supports resolutions up to 1080p@60Hz, 4K@30Hz, 36-bit deep color
•HDBaseT Lite chipset inside for the output distance up to 70m.
•Matrix can power the remote receivers, with POH, no power supply needed
for the receivers.
•Allows any source to be displayed on multiple displays (HDBaseT & HDMI)
at the same time
•Allows any HDMI display to view any HDMI source at any time
•Dolby TrueHD and DTS-HD master audio pass through HDMI output
•Volume control with Telnet and RS232 on deembedded audio
•Advanced EDID management for rapid integration of sources and displays
•Front-panel LCD display for status feedback
•Multiple switching mode: push-in button, IR remote control, RS-232 control,
and TCP/IP control
•Easy installation with rack-mounting ears
•Full 3D pass- through.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Panel Descriptions
Front Panel
1. LCD display---Show the status of input-output selection, EDID info and so on.
2. IR receiver window----Receive the IR from the remote control.
3. Power LED indicator---Indicate the status of the power for the matrix.
4. Power button---Press to power on/off the matrix.
5. HDMI output selection button 1 to 4---First Press - select the output from
button 1 to button 4
12. HDMI input selection button 1 to 4---Second Press - select the input from
button 1 to button 4
6. All button for HDMI outputs---Press to select all of the outputs from 1 to 4.
7. Menu button---Press to enter EDID set mode. Three EDID segments will
display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example:
IN1 1080P 2.0CH, means to set 1080P 2.0CH EDID to INPUT1. The blinking
segment is the one can be changed currently. Segment content items as
below:
875760 HDBaseT/HDMI/Audio Matrix 4x4
INPUT
VIDEO
AUDIO
Note
IN1 1080I 2.0CH.
IN2 1080P 5.1CH
IN3 3D 7.1CH
IN4 D1024 D1024=DVI 1024 x 768
IN5 D1080 D1080=DVI 1920 x 1080
IN6 D1200 D1200=DVI 1920 x 1200
IN7 OUT1 OUT1=Copy OUTPUT1 EDID to INPUTx
ALL OUT2 ALL=Set EDID to ALL INPUTs
OUT2=Copy OUTPUT2 EDID to INPUTx
OUT3 OUT3=Copy OUTPUT3 EDID to INPUTx
OUT4 OUT4=Copy OUTPUT4 EDID to INPUTx
OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx
OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx
OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx
OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx
8. Up selection button--- Press to change segment’s value.
9. ESC---Press to quit EDID set mode.
10. Lock LED indicator---Indicate the status of Lock.
11. Lock button---Press to lock the buttons of the front panel.
12. HDMI input selection button 1 to 4---Press to select the input from 1 to 4.
13. PTP button---Press to mirror all inputs and outputs (e.g. output 1 to input1,
output 2 to input2 and so on).
14. Selection button---Press to select segment to change setting. Selected
segment will be blinking.
15. Down selection button---Press to change segment’s value.
16. Enter button--- Press to set EDID to specified INPUT or copy EDID from
specified OUTPUT to specified INPUT.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Back Panel
1. GND --- Connect to ground.
2. IR inputs 1 to 4 --- 3.5mm stereo phone-jack, work with control processor.
3. IR outputs 1 to 4 --- 3.5mm mono phone-jack, connect to IR transmitter cable.
4. RS232 port with each HDBT out--- Connect to PC, and work with the remote
receiver.
5. Coaxial digital audio output --- Extracted audio corresponding with the HDMI
video output
6. L/R analog audio output --- Extracted audio corresponding with the HDMI
video output.
7. TCP/IP port – TCP/IP control
8. RS232 port – For control the matrix from PC or control processor
875760 HDBaseT/HDMI/Audio Matrix 4x4
9. DIP switch – Used for global EDID settings
3 2 1 0 EDID type
Combination of DIP positions
0 0 0 0 1080P 2.0CH
0 0 0 1 1080P 5.1CH
0 0 1 0 1080P 7.1CH
0 0 1 1 1080i 2.0CH
0 1 0 0 1080i 5.1CH
0 1 0 1 1080i 7.1CH
0 1 1 0 3D 2.0CH
0 1 1 1 3D 5.1CH
1 0 0 0 3D 7.1CH
1 0 0 1 4K 2.0CH
1 0 1 0 4K 5.1CH
1 0 1 1 4K 7.1CH
1 1 0 0 DVI 1280x1024
1 1 0 1 DVI 1920x1080
1 1 1 0 DVI 1920x1200
1 1 1 1 Software Control EDID
10. HDMI inputs 1 to 4--- Connect HDMI sources
11. HDBT outputs 1 to 4--- Work with remote receivers for long distance trans-
mission.
12. HDMI outputs 1 to 4--- Output for displays, AVR etc.
13. IR extension receiver input --- 3.5mm stereo phone-jack, connect to IR
receiver cable to receive the IR from remote of the matrix.
14. Power port--- Use included 24V/3.5A DC adaptor to power the matrix.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Remote Control Description
Output and Input select
A. OUTPUT-X select INPUT-Y:
1. Press OUTPUT-X (X means 1 to 4 of outputs)Press INPUT-Y( Ymeans
1 to 4 of inputs )
2. Press OUTPUT-X (X means 1 to 4 of outputs)press the left and right
arrow buttons to select the input.
B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTPress
INPUT-Y button ( Y means 1 to 4 of inputs ), then INPUT-Y switched to ALL
OUTPUTS
C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc):
Press PTP button in Zone OUTPUT
EDID Set Up
A. Fixed EDID to INPUT-Y/ALL
Press 1080I/1080P/3D/4KPress 2.0CH/5.1CH/7.1CHINPUT-Y/ALL
button in Zone INPUT
875760 HDBaseT/HDMI/Audio Matrix 4x4
B. Copy EDID of OUTPUT-X to INPUT-Y/ALL
Press COPY buttonPress OUTPUT-X buttonPress INPUT-Y/ALL button
C. User defined EDID to INPUT-Y/ALL
Press USER1/USER2 buttonPress INPUT-Y/ALL
NOTE: Pressing button sequence should be finished in 5 seconds, otherwise,
operation discarded.
Manual Output and Input select
First Press: OUTPUT select, output button 1 to 4
Second Press: INPUT select, output button 1 to 4
Specifications:
Bandwidth 2.97Gbps per color
Video Input Connectors 4x HDMI Type A, 19-pin, female
Video Output Connectors 4x HDMI Type A, 19-pin, female, 4x RJ45 Connector
Audio Output Connectors 4x RCA(SPDIF), 4x L/R
RS232 Serial port DB-9, female
TCP/IP Control 1x RJ45, female
IR input ports 5x3.5mm stereo jack
IR output ports 4x3.5mm mono stereo jack
Rack-Mountable rack ears included
Dimensions(Lx Wx D) 428mm x 235mm x 43mm, w/o feet
Shipping Weight 2.7KG
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature -4°F to 140°F (-20°C to 60°C)
Power Supply 24V/3,5A DC
875760 HDBaseT/HDMI/Audio Matrix 4x4
Application
Diagram
875760 HDBaseT/HDMI/Audio Matrix 4x4
Package Contents:
1) 1x 875760 HDBaseT/HDMI Audio Matrix 4x4
2) 1x 24V/3.5A DC power supply
3) 1x Remote control
4) 4x IR Transmitter,
5) 5x IR Receiver.
6) 1x mounting kit.
RS-232 Pin Assignment
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
875760 Remote Control Console
PIN Assignment
PIN Assignment
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
875760 HDBaseT/HDMI/Audio Matrix 4x4
RS232 and Telnet Commands
No. Command Action
0 ? Print Help Information
1 HELP Print Help Information
2 STATUS Print System Status And Port Status
3 PON Power On, System Run On Normal State
4 POFF Power Off, System Run On Power Save State
5 IR ON/OFF Set System IR Control On Or Off (Only for IR Extension)
6 KEY ON/OFF Set System KEY Control On Or Off
7 DBG ON/OFF Set Debug Mode On Or Off
8 BEEP ON/OFF Set Onboard Beep On Or Off
9 LCD ON/OFF Set LCD Always On Or Auto Turn Off When Power On
10 RESET Reset System To Default Setting,
Should Type ‘Yes’ To Confirm, ‘No’ To Discard
11 OUT xx ON/OFF Set OUTPUT:xx On Or Off
12 OUT xx FR yy Set OUTPUT:xx From INPUT:yy
13 POH xx ON/OFF
Set OUTPUT:xx POH On Or Off
xx=00: Select All OUTPUT Port
xx=[01...04]: Select One OUTPUT Port
yy=[01...04]: Select One INPUT Port
14 EDID xx CP Set Input:xx EDID Copy From Output:yy
15 EDID xx DF zz
Set Input:xx EDID To Default EDID:zz
xx=00: Select All INPUT Port
xx=[01...04]: Select One INPUT Port
yy=[01...04]: Select One OUTPUT Port
zz=00: HDMI 1080p@60Hz, Audio 2CH PCM
zz=01: HDMI 1080p@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=02: HDMI 1080p@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=03: HDMI 1080i@60Hz, Audio 2CH PCM
zz=04: HDMI 1080i@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=05: HDMI 1080i@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM
zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH PCM/DTS/DOLBY
zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=09: HDMI 4K2K, Audio 2CH PCM
zz=10: HDMI 4K2K, Audio 5.1CH PCM/DTS/DOLBY
zz=11: HDMI 4K2K, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=12: DVI 1280x1024@60Hz, Audio None
zz=13: DVI 1920x1080@60Hz, Audio None
zz=14: DVI 1920x1200@60Hz, Audio None
zz=15: User EDID 1
zz=16: User EDID 2
zz=17: GUI Download EDID
875760 HDBaseT/HDMI/Audio Matrix 4x4
16 MUTE mm TX yy Set Output(TX):yy Audio Mute ON Or OFF
17 VOL xx TX yy
Set Output(TX):yy Audio Volume to xx (only for analog Outputs!)
xx=[00...30]: Volume Value
xx=+: Volume Increase
xx=-: Volume Decrease
mm=ON: Mute On
mm=OFF: Mute Off
yy=00: Select All OUTPUT Port
yy=[01...04]: Select One OUTPUT Port
18 NET DHCP ON/OFF Set Auto IP(DHCP) ON Or OFF
19 NET IP xxx.xxx.xxx.xxx Set IP Address
20 NET GW xxx.xxx.xxx.xxx Set Gateway Address
21 NET SM xxx.xxx.xxx.xxx Set Subnet Mask Address
22 NET RB Set Network Reboot and Apply New Config!!!
875760 HDBaseT/HDMI/Audio Matrix 4x4
GUI Control
PC System: Microsoft Windows Operation System
Installation
4x4 HDMI Matrix controller is a green software. You just need to copy “4x4
HDMI Matrix Controller vx.x.exe” to the PC which is used to control the Matrix by
RS232 COM or TCP to complete installation.
Preparation
1. Connect PC and Matrix by RS232 cable or UTP cable
2. Power up Matrix (It will take about 5 seconds to be ready with “Di” beep
sound )
3. Double click “4x4 HDMI Matrix Controller vx.x.exe” icon to run it
How to control Matrix
Common information
Click to select tab page
1. COM port or TCP connect status
2. Control command process status
3. Prompt message display area
4. Date and Time display
1
2
3
4
875760 HDBaseT/HDMI/Audio Matrix 4x4
“General” page
1. Select control mode: RS232 COM mode (Auto COM ports detected) or TCP
mode
2. List detected COM ports
3. List all Matrix devices after search operation
4. Click to search all Matrix devices that connected in same subnet
5. Click to configuration the selected Matrix’s TCP control configurations
6. Click to connect or disconnect PC and Matrix ( Connection will be
established automatically before control commands sending )
7. Click to refresh device status: include device information displayed in ⑨area
and Input/output port connection status in ⑩area.
NOTE: Tab pages cannot be changed during control command is processing.
8. To enable or disable Input/output tags displaying when setting buttons on
“Setting” page focused
9. Device information display area
10. Input/output port connection status
875760 HDBaseT/HDMI/Audio Matrix 4x4
Set TCP control configuration
Click Config button to show TCP configuration window.
①Set tag to identify Matrix device
②Set IP mode: Subnet should support DHCP protocol when set Auto IP mode,
then Matrix device will obtain IP automatically. Otherwise, set Static IP mode
and designate a useable IP for Matrix device
③Set IP address, not editable when Auto IP mode selected. Note: The last IP
BYTE’s range is 2-252.
④Matrix device MAC address
⑤Click OK to set configuration. If configuration is set OK, Matrix devices will be
searched out again
⑥Click to Close the window and configuration cancelled
875760 HDBaseT/HDMI/Audio Matrix 4x4
“Port Tag” page
1. Input port tags
2. Click to edit Input port tags
3. Output port tags
4. Click to edit Output port tags
NOTE: Edit boxes are read only, click “Edit” button to pop up window to edit the
tags.
One set of Input/output port tags can be set for Matrix device when COM control
mode selected.
Input/output port tags can be set for respective Matrix device according to
device’s MAC address.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Edit Input port tags
After action of ②, edit form will pop-up as below:
Define tags for respective Input port, then devices connect the Input ports can
be easily remembered.
Click buttons with “×” caption to delete tag which is no use any more, if tag is still
used by any other Input port, delete action will be discarded.
Edit Output port tags
After action of ④, edit form will pop-up as below:
Define tags for respective Output port, then displays connect the Output ports
can be easily remembered.
875760 HDBaseT/HDMI/Audio Matrix 4x4
Click buttons with “×” caption to delete tag which is no use any more, if tag is still
used by any other Output port, delete action will be discarded.
“Setting” page
1. LED which displays Input number for respective Output port
2. Click to select Input port for respective Output port
3. Click to select previous or next Input port for respective Output port
4. Display Output from Input with tag information when mouse moves over ②
buttons
5. Pre-Setting items: Default is Port to Port
6. Click to edit selected pre-setting item
7. Set selected pre-setting item to Matrix
NOTE: When Change to this “Setting” page, software will try to refresh source
selection status of Output port.
Table of contents
Other TLS Electronics Control System manuals
