Fagerhult e-Sense Actilume User manual

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Functions and benefits
• Actilume is a control system based on the DALI protocol for
maximum comfort and up to 75% energy conservation. This
allows for a quick return on your investment.
• Actilume is a plug and play system, which does not require the
user to be specially trained in lighting control.
• Actilume consists of three small special sensors in a single case,
which are connected to a control unit with preprogrammed
modes.
• The two most common system functions, open plan oce or
oce room, can be selected with a push button on the sensor
unit.
• The light sensor is adapted and sensitive to visible light, like
the human eye. This allows for automatic energy conservation
by means of daylight adjustment, with no inconvenient side
eects for the user.
• The proximity sensor is very sensitive to human movement,
and, in combination with an optional time delay, it is adapted
for optimum performance in an oce environment.
• The lighting can easily be operated manually using one or
more spring-return push buttons or pull switches. On/o and
dimming functions are available. The same functions are also
available with remote control. In this way, the light can always
be adjusted to the user’s preferences.
• In addition, Actilume can easily be programmed to additional
special modes. These are specially designed in line with the
latest lighting installation directive, EN 12464. These additional
modes are easily programmable with a push of the IRT 9090/00
IR transmitter. The Actilume system always switches to the
maximum light level before daylight adjustment begins.
Deployment with service button on the sensor
Startup
• Requirement: Fixture correctly positioned, e.g. over the work-
space.
• Power up the fixture.
• The light will switch on after approximately 15 seconds via the
proximity sensor.
Automatic setup of daylight adjustment to approx. 5–600 lux
1. Press down the button on the sensor for more than three se-
conds, or until the light flashes once. The light will now adjust
to approximately 80 %. Make sure there is nothing preventing
the sensor from reading a neutral surface.
NOTE! No interference from daylight!
2. After 30 seconds, the Actilume system will save the light
level to a new reference value, or setpoint. This is indicated by
a flashing light. The 30-second delay is there to allow time for
the user and any items, such as a ladder, to be moved out of
the way.
Manual setting of daylight
A new value can be saved by adjusting the light manually to
the desired level using a pull cord, push button or IR transmit-
ter, then quickly pressing the service button within 30 seconds.
Instructions for manually setting a new value with an IR trans-
mitter can be found on the following pages.
After automatic/manual setup
One of the two standard modes (Mode 1 or Mode 2) can now
be selected easily in Actilume with a press of the button on the
sensor unit (press for less than 3 seconds). When the button is
released, the light will flash once or twice.
1
e-Sense Actilume

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
1a. The light is switched on when the proximity sensor is trig-
gered if the light level is too low. Daylight adjustment active.
1b. The light is switched o when the proximity sensor is
triggered if the light level is sucient. The light is switched on
when daylight adjustment is active if the level drops below the
set value.
2. Proximity.
3. Last proximity detection, 15 minute timer begins counting
down. If the sensor is triggered within the period, the timer is
reset.
4. The light is adjusted downwards and is switched o after 15
minutes.
NOTE! If the system is aected by bright sunlight for more than
15 minutes, the adjustment may go from the minimum level
to completely o. When the eect of sunlight decreases, the
light is switched on again to the minimum level and adjusts to
daylight.
Mode 1 (one flash) – Oce room
Mode 2 (two flashes) – Open plan oce solution
1a. The light is switched on when the proximity sensor is trig-
gered if the light level is too low. Daylight adjustment active.
1b. The light is switched o when the proximity sensor is
triggered if the light level is sucient. The light is switched on
when daylight adjustment is active if the level drops below the
set value.
2. Proximity.
3. Last proximity detection, 15 minute timer begins counting
down. If the sensor is triggered within the period, the timer is
reset.
4. The light is adjusted down to 20 % after 15 minutes.
5. After two hours the light is switched o completely. If the
sensor is triggered within the period, the timer is reset and the
light returns to daylight adjustment.
NOTE! If the system is aected by bright sunlight for more than
15 minutes, the adjustment may go from the minimum level
to completely o. When the eect of sunlight decreases, the
light is switched on again to the minimum level and adjusts to
daylight.
Närvaro
Precense
2
Närvaro
Precense

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Description of oset function
e-Sense Actilume has a function that allows daylight adjust-
ment to be used eectively even for lighting located away from
natural daylight. The system has two control outputs (DALI 1
and DALI 2), which are connected to fixtures. Control output
DALI 1 is also called “Window” to indicate the placement of the
fixtures for this function, while DALI 2 “Corridor” is for lighting
further inside the space. The dierence between the two is that
DALI 1 adjusts the level between the maximum and minimum
levels, around 100–3 %, and DALI 2 from 100–30 %. The oset
function also means that DALI 2 only begins to adjust when
DALI 1 has reached down to 70 %.
The eect of this function is to allow for the adjustment of
lighting that is normally ignored because the system is too
complex or the light level is wrong relative to the amount of
daylight.
See illustration below.
Example: Classroom
A normal classroom has a large window area along one of the
long walls. The lighting closest to the window is connected to
DALI 1 “Window” and is adjusted from 3–100%. The fixtures in
the centre and further inside the space are adjusted with an
oset of 30%, which compensates for the lower level of daylight
from the window. The result produces even lighting even though
the brightness is measured in line with the fixtures alongside the
window.
Example: Suspended fixture above the workspace
A suspended fixture divided into uplight and downlight is ideal
for use with the oset function. The uplight adjusts accor-
ding to DALI 2 and always provides more light upwards. The
downlight is adjusted according to personal settings between
3 and 100%. This produces a balance between personal light
and general light. If mode 2 is also used, the general light is
also extended within the space even if the person has left the
workspace.
Oset 30%
DALI 2 – Corridor
DALI 1 – Window
Ca 30%
3

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
e-Sense Actilume proximity sensor
e-Sense Actilume has a proximity sensor that responds to
infrared radiation from moving objects, such as people. The
sensor is also called a motion sensor/detector. The receiver
component “sees” positive and negative fields through the lens
faceting. When a heat source moves past the boundary bet-
ween two dierent fields, the sensor perceives a change, which
is interpreted as proximity detection. If the sensor is placed at a
height of 3.5 metres, it will detect 7.4 ⊗ 6 metres to floor level.
The measurement zone of interest is usually higher than floor
level.
e-Sense Actilume has a sensor that responds to light. The
component is placed right inside a cone so that it can read
from a specific surface. The reflected light from the fixture
and incoming sunlight is added up in the sensor’s measure-
ment. The desired setpoint must be set with no interference
from daylight. Small, sharp reflections from glass objects, for
example, may aect the total value. The sensor should be pla-
ced so that it reads the work surface in a workspace. An ideal
position would be directly above the centre of the desk, but if
the sensor is integrated into the end of a fixture it should be
directed away from the window. The placement of the sensor
and fixture must be evaluated for best results and operation.
e-Sense Actilume daylight sensor
Blue zone The blue circle marks a zone with full detection approx. 0.7 metres above ground
level. For a seated person at a workspace with a sensor in a suspended fixture approx. 2.3
metres above ground level, there is an oval detection of approx. 5⊗4 metres.
Windowsill
Window
Y=radius of reading surface
Y= 0,7xH
Sensor
Y
H
Reading surface of light sensor
H(cm)
Y(cm)
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
100 120 140 160 180 200 220 240 260 280
Y should be less than 1.2 metres to ensure that the sensor does not read light outside the
window.
4

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Settings for modes in brief
The functions that can vary are:
• The proximity sensor’s on function.
• The proximity sensor’s time since last movement.
• Light level after elapsed time. Both channels or shared function.
• Daylight adjustment activated.
• Daylight adjustment for both channels (DALI 1&2) or channel 1
(DALI 1) only.
• Start function after a power cut.
Mode Range of use DALI 1
Control/Function
DALI 2
Control/Function
Function
Proximity sensor
Time since last
proximity
Time for low
level before
switching o
Low level % Function after
power cut
Comment on
function
1 Oce room Window Corridor Auto on/o 15 0 - Switched o Oset 30%
DALI 2
2 Open-plan oces Window Corridor Auto on/o 15 120 min 20 % Switched o Oset 30%
DALI 2
3 School/classroom Window Corridor Manual on Auto o 15 0 - Switched o
Oset 30 %
DALI 2
4Oce landscape according
to EN 12464 Workspace General light Auto on/o 15 120 min, gen- eral light only 100 % Switched o
Daylight
adjustment,
workspace light
only
5Oce room according to
EN 12464 Workspace General light Auto on/o 15 0 0 Switched o
Daylight
adjustment,
workspace light
only
6 Corridor Corridor - Auto on/o 15 60 min 20 % On -
7 Toilet Washbasin Toilet Auto till/från 15 15 min, toilets
only 100 % On
Daylight
adjustment,
washbasin only
8Meeting room/conference
room with light scenarios Channel 1 Channel 2 Manual on Auto o 15 0 - Switched o No daylight adjustment
9
Oce landscape (requires
switching o centrally
with 230 V)
Window Corridor Auto on/o 15 Never switches
o 20 % On Oset 30 %
10
Oce landscape according
to EN 12464 (requires
switching o centrally
with 230 V)
Workspace General light Auto on/o 15
Never switches
o, applies to
general light
100 % On
Daylight ad-
justment, work-
space only
The choice of mode, low light level and function after a power cut can be reprogrammed with IRT 9090. The designations “Window”and “Corridor” for modes 1, 2, 3 and 9 refer to the place-
ment of the fixtures in relation to daylight from the windows.
Example functions of modes with “low level”
Modes 2, 4, 6, 7, 9 and 10 have a light level that activates 15 minu-
tes after the last proximity detection. The function is best for use
in large oces etc. where turning the lights o completely should
be avoided. If the manual o function is still selected, the function
then switches the light to the low level 15 minutes after the proxi-
mity sensor was last triggered.
5

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Setting up a preset mode
With the IRT 9090 IR transmitter (Fagerhult order no. 86155), a number
of functions can be programmed in for an e-Sense Actilume installation.
The most useful function is programming one of ten dierent modes for
an installation. An IR transmitter is loaded with a mode, and the system
is updated with the press of a button.
The following preset modes are available to choose from:
Mode 1: Oce room
Mode 2: Open-plan oces
Mode 3: School/classroom
Mode 4: Oce landscape according to EN 12464
Mode 5: Oce room according to EN 12464
Mode 6: Corridor
Mode 7: Toilet
Mode 8: Meeting room/conference room with light scenarios
Mode 9: Oce landscape (requires switching o centrally with 230 V)
Mode 10: Oce landscape according to EN 12464 (requires switching
o centrally with 230 V)
Programming a preset mode
1. Press button: MODE
2. Select a MODE from 1 to 10
3. Send the new information with a press of the green button.
Aim carefully at the IR receiver – the sender has a very narrow
beam to prevent accidental transmission to nearby systems.
The light will flash once to confirm the new setting.
Setting daylight level
With the IRT 8099 IR transmitter (Fagerhult order no. 86155), it is easy
to set the setpoint for daylight adjustment. Any value can be read
with a luxmeter placed on the surface towards which the sensor is
directed. It is important to remember that a lux value only applies to a
given point and does not correspond to the entire surface read by the
Actilume light sensor.
1. Adjust the light to the desired level using the up and down buttons.
NOTE! Avoid interference from daylight when this setting is applied.
2. Save the new level using the SAVE button. The light will flash to
indicate that programming is complete.
Always aim carefully at the IR receiver – the sender has a very narrow
beam to prevent accidental transmission to nearby systems.
6

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Full light level and light o can be tested with IRT 9090.
1. Press the ON or OFF button for full light and light o respectively.
Function test of the proximity sensor’s detection range
It is important that e-Sense Actilume detects proximity in the
correct way. Check the function with the test button. The light
will flash once for each movement that is detected. This fun-
ction can be used to determine how large an area the sensor
can sense. Try walking towards the sensor until the first indica-
tion. If the installation is a workspace, you can test its sensiti-
vity by sitting and making small movements.
1. Press the TEST button once. The light will adjust downwards.
First check that there are no people under the sensor. Walk
slowly towards the zone until the light flashes. Reset the fun-
ction by pressing the TEST button again.
To check the mode that has been programmed, e-Sense Acti-
lume can indicate the mode that is selected.
1. Press the MODE button once.
The light is first adjusted downwards. Be ready to count the
number of times the light flashes. The function may need to be
repeated in order to count correctly.
Checking the selected mode – MODE
Resetting the programming
e-Sense Actilume is easy to reset if you are unsure of certain se-
lected functions. The system will return to factory settings: Mode
1 (oce room) and daylight adjustment approximately 600 lux.
1. Press the BASICS button once.
The light will flash to indicate the function.
Switch light on/o
7

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Changed function after a power cut
Modes 1–5 and 8 keep the light o after power returns. Modes
6–7 and 9–10 set the light to full. This can be changed with IRT
9090 as follows:
1. Press the POWER UP button once.
2. Select a new start function with the ON and OFF buttons.
3. Send the new information with a press of the green button.
NOTE! Modes 1–5 switch o after a power cut. The system
requires at least a 15 second reset period before the light can
be switched on using the proximity sensor.
Mode Range of use Function after
power cut
1 Oce room Switched o
2 Open-plan oces Switched o
3 School/classroom min. Switched o
4 Oce landscape according to EN 12464 Switched o
5 Oce room according to EN 12464 Switched o
6 Corridor On
7 Toilet On
8Meeting room/conference room with light
scenarios Switched o
9Oce landscape
(requires switching o centrally with 230 V) On
10 Oce landscape according to EN 12464
(requires switching o centrally with 230 V) On
Change level before switching o
The low level (background) before switching o, available in mo-
des 2, 6 and 9, is preprogrammed to 20 %. In modes 4, 7 and 10,
the level only applies to DALI 2 and is selected to 100 %. The level
can be changed as follows for all these modes.
1. Press the BACKGROUND button once.
2. Select a new light level for 10, 20, 30, 40, 50, 60 or 70%. The
minimum level is selected with the 0 button.
3. Send the new information with a press of the green button.
Mode Range of use Low level %
1 Oce room -
2 Open-plan oces 20 %
3 School/classroom min. -
4 Oce landscape according to EN 12464 100 %
5 Oce room according to EN 12464 0
6 Corridor 20 %
7 Toilet 100 %
8Meeting room/conference room with light
scenarios -
9Oce landscape
(requires switching o centrally with 230 V) 20 %
10 Oce landscape according to EN 12464
(requires switching o centrally with 230 V) 100 %
8

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.
Programming with IRT 8099/00 or IRT 9090/00
Actilume systems for light adjustment consist of a small,
compact sensor and a control unit designed for installation in
fixtures. Actilume is a simple system produced for plug and
play lighting solutions, mostly in oce environments. A sus-
pended fixture, an open plan oce solution with nine fittings,
or, for example, an oce room with four fixtures, are perfect
for controlling with Actilume. Actilume uses a master–slave
control, which is easy to install, deploy and use.
NOTE! Important!
Philips has updated the Actilume system and has added
functions for Philips OccuSwitch DALI also. This means that
the programming tool IRT 8099/00 has been replaced with
IRT 9090/00 with eect from 2014. All the original program-
ming functions are the same, but the new functions cannot be
programmed into Actilume generation 1, which Fagerhult uses
in all its fixture solutions.
The manual describes how to program using IRT 8099/00;
the positions of the buttons may have changed in the newer
IRT 9090/00 but the functions are the same. The functions
available in IRT 9090/00 that cannot be programmed are the
following (used only in OccuSwitch DALI):
• I/II Funktion
• Config.
• Link
• DALI prog.
• Delay
• PIR
• Daylight
• RF channel
IRT8099/00 IRT9090/00
9