RF ELITE User manual

ELITE Remote control System
Quick Installaon Guide (systems only)
The Elite system provides 4 switches each capable of switching up to 1KW (4A @ 230V). Each channel is independ-
ent and separately controlled. The ELITE Remote control system provides 230V mains switched outputs via each ter-
minal.
1. First mount the ELITE system receiver box in the wall in your desired locaon.
2. Open the enclosure by removing xing screws from the enclosure front and then removing the front from the
enclosure.
3. Wire the LIVE, Neutral and Earth connecons to the power supply screw terminal as shown below
(shown as A).
4. Wire your load(s) as required (shown as B).
5. Once all required wiring is complete, use the handheld ELITE transmier to switch the outputs on and o.
6. As supplied, the handheld will operate the outputs - Buon 1 to output 1, Buon 2 to output 2 etc.
7. All buons will operate in a latching mode - Press for on, press again for o. It is possible to change the operaon
to momentary mode by ng the links (shown as C)
8. For advanced operaon such as adding extra transmiers dierent buon mapping opons consult
datasheet.
Fig 1.1
Please contact RF Soluons if any components are missing
Sales: [phone] Tech. Support: [phone]
RELAY 1 RELAY 2 RELAY 3 RELAY 4
FUSE
POWER
TIMER SELECT
FUSE
RELAY 1
RELAY 2
RELAY 3
RELAY 4
SYNC
SIGNAL TEST
ERASE
FUSE FUSE
FUSE
230V INPUT
SUPPLY
A
B
LOAD
C
ANT
QS-ELITE-4
ELITE Remote Control System
Quick Start Guide
What’s in the box?
1 x Receiver with 5 addional
cable glands
1 x Transmier (system only)
Please contact RF Soluons if any components are missing.
Sales: [phone] Tech Support: [phone]
or
ELITE Remote
Control System
Quick Start Guide
For full details of ELITE’s
programmable features, see
the ‘ELITE Datasheet at
www.rfsoluons.co.uk.

ELITE Remote control System
RELAY 1 RELAY 2 RELAY 3 RELAY 4
FUSE
POWER
TIMER
Timer Select Button –Used to select timer mode
Erase Button –Press and hold to erase all pairings, see
advanced operation for individual erase
Signal Test mode –Press to enter signal test mode
Sync/Pair Button –Press once to auto pair. See
Advanced operation for other pairing options.
Momentary/Latching Jumper Links –It is possible to set the relay switches on
the ELITE receiver to either momentary or latching operation.
Latching (link removed) - One press for on, one press for off.
Momentary (link fitted)- On while button is held only.
To set a relay switch to either momentary/latching choose the associated link cap.
NOTE: If link is changed, power cycle the receiver (turn off/on) otherwise it will
stay in the same mode it was previously set in.
230Vac power
input
Power input fuse –must be 500mA
(Fast blow fuse recommended)
Relay switch terminals:
Neutral
Live
Earth
FUSE
RELAY 1
RELAY 2
RELAY 3
RELAY 4
SYNC
TEST
ERASE
FUSE FUSE
FUSE
Output Fuses must be 4A
(Slow blow fuses recommended)
Status LEDs–Flash when
signals are sent/received
L N E L N E L N E L N E L N E
8
7
6
5
4
3
2
1
Mag sync –Touch a
magnet to the plastic
case in the cross
hatched area to
replicate the sync
button on board
without opening the
case
Receiver Guide
ELITE Remote control System
Pairing a transmier
NOTE: The transmier supplied with the system should already be paired.
If an addional transmier needs to be paired, simply follow the below instrucons.
1. To SYNC a specic ELITE handheld transmier
buon to a specic output on the ELITE receiver
box—press and release the SYNC buon on the
ELITE receiver board.
2. The ELITE receiver will ash all its relay output LED’s at a high rate to show that it is ready to
SYNC.
3. Press and release the SYNC buon again—the ELITE receiver will ash output LED1 this is
showing that output 1 is selected. Pressing and releasing the SYNC buon again will select
output 2 and so on, through to output 4.
4. Once you have selected the required output (only that out-
put LED is ashing) press and release the SPECIFIC buon
on the transmier that you wish to SYNC to the receiver.
5. The ashing LED’s will go out, the SYNC LED will ash quick-
ly for 2 seconds then go out.