Toa SR-F09 User manual

OPERATING INSTRUCTIONS
SPEAKER SYSTEM SR-F09
SR-L09
SR-L05
Thank you for purchasing TOA’s Speaker System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ............................................................................. 2
2. GENERAL DESCRIPTION .......................................................................... 3
3. FEATURES ............................................................................................................ 3
4. DIMENSIONAL DIAGRAMS ...................................................................... 4
5. WIRING DIAGRAMS ....................................................................................... 4
6. INPUT CONNECTORS .................................................................................. 5
7. CONNECTIONS .................................................................................................. 5
8. FLYING (SR-F09 ONLY) ............................................................................... 6
9. SPEAKER STAND FOR SR-F09 ............................................................. 6
10. CHANGE FROM SINGLE- TO BI-AMPLIFIER DRIVE ............ 8
11. DIGITAL PROCESSOR SETTINGS .................................................. 11
12. SPECIFICATIONS ........................................................................................ 12

2
1. SAFETY PRECAUTIONS
• Beforeinstallationoruse,besuretocarefullyreadalltheinstructions inthis sectionforcorrectandsafe
operation.
• Besuretofollowalltheprecautionaryinstructionsinthissection,whichcontainimportantwarningsand/or
cautionsregardingsafety.
• Afterreading,keepthismanualhandyforfuturereference.
Safety Symbol and Message Conventions
Safetysymbolsandmessagesdescribedbelowareusedinthismanualtopreventbodilyinjuryandproperty
damage which could result from mishandling. Before operating your product, read this manual rst and
understandthesafetysymbolsandmessagessoyouarethoroughlyawareofthepotentialsafetyhazards.
Indicatesapotentiallyhazardoussituationwhich,ifmishandled,could
resultindeathorseriouspersonalinjury.
Indicatesapotentiallyhazardoussituationwhich,ifmishandled,could
resultinmoderateorminorpersonalinjury,and/orpropertydamage.
WARNING
CAUTION
When Installing the Unit
• Referallinstallationworktothedealerfromwhom
the speaker was purchased. Installation for ying
requires extensive technical knowledge and
experience. The speaker may fall off if incorrectly
installed,resultinginpossiblepersonalinjury.
• Installtheunitonlyinalocationthatcanstructurally
support the weight of the unit and the mounting
bracket. Doing otherwise may result in the unit
falling down and causing personal injury and/or
propertydamage.
• FlyingPrecautions(SR-F09only)
 Besuretofollowtheinstructionsbelow.Otherwise,
the suspension wires or belts may be off or snap
and the speaker may fall off, causing personal
injury.
· Check to conrm that the suspension wires and
beltsarestrongenoughtowithstandthespeaker
load.
· Theconnectorsofthesuspensionwiresandbelts
mustbesecurelylinkedwiththoseofthespeaker.
· All parts and components (such as enclosures,
metalpieces,andscrews)mustbefreefromany
deformation,crack,andcorrosion.
· Besuretousescrewssuppliedwiththeoptional
yinghardwarewheninstallingthespeakerusing
suchhardware.
When Installing the Unit
• Install the unit only in stable locations, and make
appropriatearrangementstopreventitfromfalling
down or rolling cross the oor. If it falls down or
moves, this may cause personal injury and/or
propertydamage.
• When unpacking or moving the unit, be sure to
handle it with two or more persons. Falling or
droppingtheunitmaycausepersonalinjuryand/or
propertydamage.
When the Unit is in Use
• Donotstandorsiton,norhangdownfromtheunit
asthismaycauseittofalldownordrop,resultingin
personalinjuryand/orpropertydamage.
• Donot operatethe unitfor an extendedperiod of
timewiththesounddistorting.Doingsomaycause
theconnectedspeakerstoheat,resultinginare.
WARNING CAUTION

3
2. GENERAL DESCRIPTION
TheSR-F09,SR-L05,andSR-L09aredesignedforon-the-roadapplications.Theyareallhigh-power,high
qualityspeakersystemsthatcanstandup.
3. FEATURES
• The SR-F9 has an internal passive network and is driven by a single amplier. (This can be changed to
bi-amplierdrivebychangingtheirinternalconnectorconnections.)TheSR-L05andSR-L09arebothsub-
woofersystems.Thesespeakersareallusedinconjunctionwithadigitalprocessor.
• The SR-F09 houses a constant directivity (CD) horn as a tweeter with directional angle of
60°horizontalby40°vertical.
• TheSR-F09hasyinghardwareontheirtopandbottompanels.Thebottompanelisalsoprovidedwithnuts
forinstallinganoptionalstand.
• "Neutrik"connectorNL4MPandascrewterminalarebothprovidedforinput.TheSR-F09isequippedwith
two"Neutrik"connectorssoastopermitparallelspeakerconnection.

4
829
629
606 502
452
629
221
195
30°
390
619
364
315
155
120
224
2-M8 Nut
Center of gravity
Flying fitting (4 places)
4. DIMENSIONAL DIAGRAMS
[SR-F09]
Unit: mm
[SR-L09] [SR-L05]
[SR-F09] [SR-L09] [SR-L05]
5. WIRING DIAGRAMS
Screw terminal 4P
NL4MP NL4MP
1+
2+
1
-
2 -
1+
2+
1
-
2 -
(+)
(
- )
Screw terminal 4P
NL4MP
1+
2+
1
-
2 -
(+)
(
- )
(+)
(
- )
(LEFT)
(RIGHT)
Screw terminal 2P
NL4MP
1+
2+
1
-
2 -
(+)
(
- )

5
7.3. About the Power Amplifier to Connect
Itisrecommendedthatyouuseapoweramplierwithoutputofover400W(perchannelwhenan8Ωloadis
connected).
[SR-F09] [SR-L09] [SR-L05]
• PinsoftheNeutrikconnectorareconnectedasshowninthetablebelow.
• Theusableconnector(onthecableend)fortheNL4MPRconnectorisNeutrik'sNL4FC.
6. INPUT CONNECTORS
• Theguresbelowshoweachspeaker'sinputconguration.Becausetheconnectorisinternallyconnectedin
parallel to the screw terminal, you can use either of the two.
PinNo. SR-F09 SR-L09 SR-L05
1 + Speaker +
- -
1− Speaker−
- -
2 +
-
Speaker + Speaker +
2−
-
Speaker− Speaker−
7. CONNECTIONS
7.1. Combination with a Sub-woofer
INPUT
SR-F09
SR-L09, SR-L05
MAIN OUT
BASS OUT
Digital Processor* Power amplifier
*Forthedigitalprocessorsettings,seep.11.
INPUT MAIN OUT
SR-F09
Power amplifier
Digital Processor*
7.2. Singular System of SR-F09
*Forthedigitalprocessorsettings,seep.11.

6
8. FLYING (SR-F09 ONLY)
Shownbelowarethegeneralyingmethods:
[Precautions]
• Twoying ttings are providedoneach of the top
andbottompanels.
• Provide at least 2 suspension points at each
speaker.
• The maximum number of speakers that can be
suspendedverticallyisthree.
Never suspend as illustrated below:
• Flying through only
one suspension point
on the top panel.
• Flyingthroughhandles.
• Verticalsuspensionof
more than 3 speakers.
•Flyingwithasingle
loopedwire
• Flying using the nuts
on the bottom surface
Besuretoreferyingconstructionworktothedealerfromwhom
thespeakerwaspurchased.
WARNING
9. SPEAKER STAND FOR SR-F09
ThespeakerstandmanufacturedbyKöning&MeyerGmbH(K&M)ofGermanyismadeavailableforusewith
TOA'sSR-F09speaker.
ThespeakerstandconsistsofaStandandaStandBracket,whicharesoldseparately.
Inaddition,separatelyprepare2speakermountingscrewstosecurethebrackettothespeaker.
Speakerstand:Model213
Standbracket: Model195/8
Speakermountingscrew: M8x20

7
9.1. USAGE(RefertoFig.1.)
Step 1. Extendthestand’slegs.
Loosenthetripodxingscrewandopenthe
tripodlegsoutwardsothatthestaysbecome
level.
Step 2. Attach the stand bracket to the speaker
usingthespeakermountingscrewsandplain
washers.(Fig.2).
Step 3. Loosen the bracket xing screw, then place
thespeakeronthestand.
After setting the speaker's orientation,
retightenthebracketxingscrew.
Step 4. Adjustthestandheight.
4-1. Loosentheheightxingscrew.
4-2. Loosenthehandlexingscrewandraisethe
handle,thenretightenthehandlescrew.
4-3. While holding down the lock button, adjust
the speaker's height by turning the height
adjustmenthandle.(Clockwiserotationraises
thespeaker.)
Note
Youcannotrotatethehandleunlessthelock
buttonis continuously pressed.Tocomplete
the height adjustment, ensure that the shaft
is locked when the lock button is released.
(Thiscanbecheckedbyrotatingthehandle
slightly.)
Step 5. Retightentheheightxingscrew.
Step 6. Loosen the handle xing screw and replace
the handle by tilting it up, then retightenthe
handle screw. Leave the handle tilted up
exceptwhenadjustingtheheight.
Step 7. After use, reverse the above procedures to
putawaythestand.
Stand bracket
195/8
Bracket fixing screw
Height fixing screw
Tripod fixing screw
Tripod leg
Stay
Lock botton
Handle fixing screw
Height adjustment handle
Height adjuster
SR-F09
Speaker stand
213
1
3
4-1, 5
4-3
4-2, 6
(Fig. 1)
(Fig. 2)
Plain washer
(for M8)*
Speaker mounting screw
M8 x 20*
Stand bracket
2
* Prepare separately.
Plain washer (for M8): 2 pcs
Speaker mounting screw M8 x 20: 2 pcs
• Onlyusethestandontheat,hardgroundoroorsurfaces.
• Avoidinstallingthestandinthepassagewherepeoplecouldtripover
thetripodlegs.
• When using the stand outdoors, avoid locations exposed to strong
winds.
• Tominimizethechance ofthe stand topplingover,avoidextending
thestandtoohigh.
• Whenthestandcouldfalldown,besuretosecureitwithguywiresor
otherdevices.
CAUTION

8
10. CHANGE FROM SINGLE- TO BI-AMPLIFIER DRIVE
TheSR-F09canbedrivenbybi-ampliersifwiringoftheirinternalconnectorsischanged.Whenusingthese
speakersincombinationwiththeSR-L09,itsinternalwiringmustalsobechanged.
10.1. Changing Internal Wiring
10.1.1. SR-F09
Step 1. Removefrontgrillexingscrews(4places)to
removethefrontgrille.
Step 2. Remove horn xing screws (8 places) to
removethehorn
Step 3. Disconnectconnectorsinsideanenclosure.
Step 4. Connect a connector having a marker on
it to a similarly marked connector, and
an unmarked connector to an unmarked
connector.
Step 5. Replacethehornusingscrews.
Step 6. Replacethefrontgrilleusingfrontgrillexing
screws.
Horn removed.
Connector
Front grille
Front grille
fixing screw
Connector
Marker

9
Step 1. Removefrontgrillexingscrews(12places)
toremovethefrontgrille.
Step 2. Removethewooferlocatedontherighthand
side as viewed from the front by removing
eight screws.
Step 3. Disconnectconnectorsinsideanenclosure.1.
Removefrontgrillexingscrews(12places)
toremovethefrontgrille.
Step 4. Connectaconnectorhavingamarkeronitto
asimilarly-markedconnector.
Step 5. Replacethewooferusingscrews.
Step 6. Replacethefront grilleusing the frontgrille
xingscrews.
10.1.2. SR-L09
Connector
Woofer removed.
Front grille
Front grille
fixing screw Connector
Marker
Label supplied with SR-F09 Label supplied with SR-L09
10.2. Input Connector Connections
• Changeeachspeaker'sinputconnectorsasfollows.Also,attachthesuppliedmarker(label)tochangethe
indication.
•PinsoftheNeutrikconnectorareconnectedasshowninthetablebelow.
•Because the connector is internally connected in parallel to the screw terminal, you can use either of the
two.
*The"LEFT"andthe"RIGHT"arethedirections
asviewedfromthefront.
PinNo. SR-F09 SR-L09
1 + LOW+ LEFT*+
1 – LOW− LEFT*−
2 + HIGH+ RIGHT*+
2− HIGH− RIGHT*−

10
INPUT
INPUT
INPUT
Power amplifier
Power amplifier
Power amplifier
SR-F09
SR-F09
SR-F09
SR-L09
SR-L05
Digital Processor
Digital Processor
Digital Processor
HIGH
LOW
HIGH
LOW
HIGH
LOW
Screw terminal 4P Screw terminal 4P
NL4MP NL4MP NL4MP
1+
2+
1
-
2 -
1+
2+
1
-
2 -
1+
2+
1
-
2 -
(+)
(
- )
(+)
(
- )
(LEFT)
(RIGHT)
(+)
( - )
(+)
(
- )
LOW
HIGH
10.3. Connection diagram
[SR-F09] [SR-L09]
10.4. Connections

11
Delay
(ms)
Freq. (Hz) Gain (dB)Freq. (Hz)
Gain
(dB) Polarity
−4.0
−3.5
+3.5
−10.0
TYPETYPE
LinkwitzRiley
LinkwitzRiley
LinkwitzRiley
Q
HPF/LPF
INVERSE
High Shelving
PEQ
PEQ
PEQ
PEQ
0.292
0 NORMAL 1.414
2.079
SR-F09 LOW
SR-F09 HIGH
100
580
30
1.0k
1.0k
3.633
12.5k
11.8k
3.15k
2.371
0
[Bi-amplifier drive for SR-F09]
HPF (12dB)
HPF (24dB)
LPF (24dB)
X-over Combination Filter
Channel
+6.0
+10.0
Delay
(ms)
Freq. (Hz)
Gain
(dB)
0 NORMAL
SR-F09 LOW
−10.0 INVERSE
SR-F09 HIGH
Freq. (Hz) Gain (dB)
−4.0
−3.5
+3.5
+2.5
Polarity TYPETYPE
LinkwitzRiley
LinkwitzRiley
LinkwitzRiley
LinkwitzRiley
LinkwitzRiley
Q
HPF/LPF
0.667
NORMAL
SR-L09
PEQ
High Shelving
PEQ
PEQ
PEQ
PEQ
4.318
0.292
1.414
2.079
40
20
80
160
580
100
1.0k
1.0k
3.633
12.5k
11.8k
3.15k
2.371
0
[Bi-amplifier drive for SR-F09+SR-L09/L05]
HPF (24dB)
HPF (24dB)
HPF (24dB)
LPF (24dB)
LPF (24dB)
X-over Combination Filter
Channel
+5.0
+5.0
+10.0
−3.0
−3.0
Gain
(dB) Polarity Delay (ms)
TYPETYPE
LinkwitzRiley
Freq. (Hz) Freq. (Hz)
[Single-amplifier drive for SR-F09]
Gain (dB) Q
HPF (12dB)
HPF/LPF
PEQ
PEQ
PEQ
PEQ
PEQ
0 NORMAL
X-over Combination
1.414
1.414
2.997
2.997
2.997
SR-F09 200
70
550
70
16k
1.7k
Filter
Channel
+6.0
+3.0
+8.0
Delay
(ms)
Freq. (Hz) Gain (dB)Freq. (Hz)
−3.0
−3.0
INVERSE
TYPETYPE
LinkwitzRiley
[Single-amplifier drive for SR-F09+SR-L09/L05]
Q
HPF/LPF
SR-L09
PEQ
PEQ
PEQ
PEQ
1.000
0 NORMAL 2.997
2.997
2.997
1.414
SR-F09
200
50
550
70
1.7k
16k
0
0
HPF (12dB)
LPF (12dB)
X-over Combination Filter
Gain
(dB) Polarity
Channel
+6.0
+3.0
+6.0
11. DIGITAL PROCESSOR SETTINGS

Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1,Minatojima-Nakamachi,Chuo-ku,Kobe,Hyogo,
Japan
Authorizedrepresentative:
TOAElectronicsEuropeGmbH
Suederstrasse282,20537Hamburg,
Germany
URL:http://www.toa.jp/
133-01-00160-00
12. SPECIFICATIONS
[SR-F09]
Enclosure Bass-reextype
PowerHandlingCapacity Continuouspinknoise:200W
Continuousprogram: 600W
RatedImpedance 8Ω
Sensitivity 100dB(1W,1m)
FrequencyResponse 70Hzto20kHz*
CrossoverFrequency 1kHz*
Speaker Component Lowfrequency: 30cmcone-type
Highfrequency: CDhorn
 (60°horizontalx40°vertical)ttedwithcompressiondriver
Input Connector NeutrikNL4MPx2andM5screwterminal,distancebetweenbarriers:12.2mm
Finish Enclosure: Plywood,black,paint
Frontgrille:Steelplate,black,acrylicpaint
Dimensions 390(w)x619(h)x364(d)mm
Weight 35 kg
Accessories Label...... 2 pcs
*WhenrecommendedparametersareappliedbytheoptionaldigitalspeakerprocessorDP-SP3
Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.
Model SR-L09 SR-L05
Enclosure Bass-reextype
PowerHandlingCapacity Continuouspinknoise:300W
Continuousprogram: 900W
Continuouspinknoise: 150W
Continuousprogram: 450W
RatedImpedance 4Ω 8Ω
Sensitivity 96dB(1W,1m) 93dB(1W,1m)
FrequencyResponse 35Hzto1kHz
CrossoverFrequency 125Hz*
Speaker Component Lowfrequency:38cmcone-type×2 Lowfrequency:38cmcone-type
Input Connector NeutrikNL4MPandM5screwterminal,distancebetweenbarriers:12.2mm
Finish Enclosure: Plywood,black,paint
Frontgrille:Steelplate,black,acrylicpaint
Dimensions 829(w)×629(h)×606(d)mm 452(w)×629(h)×502(d)mm
Weight 67 kg 36 kg
Accessories Label...... 2 pcs
[SR-L09, SR-L05]
*WhenrecommendedparametersareappliedbytheoptionaldigitalspeakerprocessorDP-SP3
Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.