Toa FB-601W AS User manual

533-06-212-00
TOA Corporation
OPERATING INSTRUCTIONS
FB-601B AS
TOA Corporation
FB-601W AS
SUBWOOFER SYSTEM
Thank you for purchasing TOA’s Subwoofer System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
•
•
regarding safety.
•After reading, keep this manual handy for future reference.
Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.
Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions
WARNING in death or serius personal injury.
indicates a potentially hazardous situation which, if mishandled, could result
.
Note :
8
Model
FB-601B AS FB-601W AS
Continuous Program Input
120 W per Channel
Rated Impedance
6
Sound Pressure Level
85 dB (1W, 1m)
Frequency Response
40 ~ 190 Hz (-10dB below peak of SPL)
Speaker Component
Double Subwoofer : 16 cm cone-type
Input / Output Terminal
Push-in connector
(bridging terminal, 8 pole type)
Front Panel
ABS Resin Black
ABS Resin White
Cabinet
Partikel Board with Vinyl Black
Partikel Board with Vinyl White
Mesh Speaker Grill
MEU R5001 Hard Black
Dimension
210 (W) x 390 (H) x 563 (D) mm
Weight
11.5 kg
Accessory
Ω
Rubber Foot ... 4 pcs
Tapping Screw 3x14 ... 4 pcs
Bracket (Black paint) ... 4 pcs
The design and specification are subject to change without notice for improvement.
Switch Position When Using 4 Speakers
* NOTE :
OUTPUT
RIGHT LEFT
RIGHT LEFT
INPUT
Speaker unit
Speaker unit
Subwoofer unit
Switch Label
4 SPEAKER
2 SPEAKER
The switch is factory preset
to Amplifier to Amplifier
9 mm
[Stripped conductor
of cable]
Input terminal
* Input Terminal Speaker
from subwoofer
to speaker
Make sure the switch position
is appropriate to use with
the amount of speaker.
4 SPEAKER
2 SPEAKER
FB-601B AS
model
SUBWOOFER SYSTEM
MADE IN INDONESIA
IMPEDANCE
CONT.PGM.INPUT
6 Ω / CHANNEL
120W / CHANNEL
TOA Corporation
Recommended Speaker :
* When using two speaker, set switch position to “ 2 SPEAKER ” . ( refer to point 7.1 )
Factory recommends TOA Speaker model F-1000B/W to be connected to FB-601 Subwoofer
* When using four speaker, set switch position to “ 4 SPEAKER ” . ( refer to point 7.2 )
to “4 SPEAKER”.
Bracket (White paint) ... 4 pcs
•Avoid installing or mounting the unit in unstable locations, such as on rickety table or slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
When Installing the unit
•Install the unit only in location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
•Since the unit is designed for in-door use, do not install it outdoors. If installed outdoors, the aging of parts causes the
unit to fall off, resulting in personal injury. Also, when it gets wet with rain, there is a danger of electric shock.
•Owning to the unit’s size and weight, be sure that at least two persons are available to install the unit. Failure to
do so could result in personal injury.
•Do not use other methods than specified to mount the bracket. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injury.
•Use screws that are appropriate for the ceiling’s or wall’s structure and composition. Failure to do so may cause
the unit to fall, resulting in personal injury.
•Ensure that all screws are securely tightened. If they are not tightened or firmly secured after installation, the unit
resulting in personal injury.
•Use the specified mounting bracket in combination. Doing otherwise may cause the unit or component to fall
off, resulting in personal injury.
•Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the unit to fall, which could result in personal injury.
CAUTION in moderate or minor personal injury, and/or property damage.
indicates a potentially hazardous situation which, if mishandled, could result
•When unpacking or installing the unit, be sure to handle it with two or more persons. Falling or dropping the unit
may cause personal injury.
When Installing the unit
•Avoid touching the unit’s sharp metal edge to prevent injury.
To avoid electric shock, be sure to switch off the amplifier’s power when connecting speakers.
•
• Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal injury
and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.
When the unit is in use
• Make sure that the volume control is set to minimum position before power is switched on. Loud noise produced
at high volume when power is switched on can impair hearing.
• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate and result in a fire.
Manufacturer :
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative :
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
URL: http://www.toa.jp/
SPECIFICATIONS
7.2.

6.
4 - Rubber foot
4 - Tapping Screw 3 x 14
Subwoofer Unit
Subwoofer Unit
INSTALLATION
Side Corner Wall
Vertical direction
5. INPUT CONNECTION
OUTPUT
RIGHT LEFT
RIGHT LEFT
INPUT
Blk
(-)
Red
(+)
Red
(+) Red
(+)
Red
(+)
Blk
(-)
Blk
(-)
Blk
(-)
9 mm
[ Stripped conductor of cable ]
Input and Output Connector
Reproduction of sound emitted from the subwoofer unit differs depending on installations. The figure below shows
the appropriate locations for in-door use.
Use standard rubber foot accesories when installing the unit in a flat floor to avoid the units from sliding or moving.
Fixed rubber foot on the side of unit which facing to the floor.
Horizontal direction
CONNECTS SPEAKERS TO THE SUBWOOFER
Switch Position When Using 2 Speakers
9 mm
[Stripped conductor of cable]
Input terminal
* Input Terminal Speaker
OUTPUT
RIGHT LEFT
RIGHT LEFT
INPUT
Subwoofer unit Speaker unit
4 SPEAKER
2 SPEAKER
Speaker unit
Speaker unit
7.
to Amplifier
to Amplifier
Make sure the switch position matches the amount of speakers connected.
Non-Compliance could result in damages to the unit.
Change the switch position
using screw driver (-)
to “2 SPEAKER”.
For wall installation, remove two of the four Flat screw from the unit. Refer to wall bracket mounting dimensions
when installing the brackets.
Remove 2 of 4 Flat screw
For ceiling installation, remove all the Flat screw from the unit. Refer to ceiling bracket mounting dimension
when installing the brackets.
Remove all Flat screw
Fix Subwoofer to
bracket with Flat screw
from subwoofer’s cabinet
from subwoofer cabinet
Fix Subwoofer to
bracket with Flat screw
[Wall Bracket mounting dimensions]
3 6 0
3 0 3 0
4 5
8-Ø9
4 5
16-Ø9
4 5
3 03 0
4 5 4 5
3 0 3 0
4 5
477
[Ceiling Bracket mounting dimensions]
FB-601B AS
model
SUBWOOFER SYSTEM
MADE IN INDONESIA
IMPEDANCE
CONT.PGM.INPUT
6 Ω / CHANNEL
120W / CHANNEL
TOA Corporation
Floor
50
40
50
40
DIMENSIONAL DIAGRAM
210
390
Input and output connector
[ Unit : mm ]
563
Switch
[ Front ] [ Side ] [ Rear ]
3. FEATURES
•
•
Compact in dimension and compatible for in-door use.
Amount of connected speakers to the unit is selectable by using switch in rear side.
Wall mount, ceiling mount or floor stand application (with standard bracket and accesories).
•
360
55
278
100 103
50
50
50
50
* NOTE :
The switch is factory preset
to “4 SPEAKER”.
2. GENERAL DESCRIPTION
TOA’s FB-601B AS/FB-601W AS is subwoofer system with two input channels and two output channels for setting
with two speaker at each channel. It is designed for in-door use, and is particularly ideal for reproducing
dynamic low-frequency sound for both permanent and temporary installations.
4.
7.1.
6.3. Ceiling Installation
6.2. Wall Installation
6.2. Floor Installation
Install the unit only in location that can structurally support
the weight of the unit and the mounting bracket.
Install the unit only in location that can structurally support
the weight of the unit and the mounting bracket.
3 6 0