Top RC Model F-16 Fighting Falcon User manual

第 1 页

第 2 页

第 3 页

Accessory list for the installation of aileron and flap.
3. Glue the horns to the aileron, Connect the horns to the
servo arms with the linkage and lock each side with
screws and nut. Make sure the aileron can at least 30mm
up and down movement.
1. Trim slots in appropriate position for wing servos right
and left, assemble the servo to the wing with screw, use a
steel wire to drag the servo arm to appropriate position
with the servo .
4. Secure the missile rail to the wing with screws, put the
wing carbon fiber bars to the wings .
2. Adjust the servo arm to the right position and fixing it to
the servo with screw, see picture .
5. Assemble the wing to the fuselage through the carbon
fiber bar, allow the servo lines go inside the fuselage,
secure the wing with the screws from the holes in bottom
of the fuselage.
第 4 页

Accessory list for the installation of stab and vertical fin . 8. Assemble the stab to the fuselage and make sure it can
turn freely .
6. Assemble the servo to the stab servo mount, trim a slot in
the stab root position of fuselage base on the 3mm ply jig.
9. Assemble the servo of the vertical and install it to the
tail fuselage with screws and screw driver .
7. Assemble the stab servo to appropriate position in the
fuselage with screws and make sure the screw with bearings
can move through the slot smoothly .
10. Install the servo cover to the tail fuselage with screws
as pictures below .
第 5 页

11. Glue the vertical alu tubes to the vertical fin. Accessoriesfor assembling the fuselage fuse fairing.
12. Assemble the vertical fin to the tail fulse . 14. Install the screws into the holes of fuse fairing tightly
.
13. Lock the vertical fin by screws from the tail fuselage
holes, make sure the rudder can move smoothly .
15. Open the top hatch, lock the fuse fairing to the
fuselage from inside of the fuselage with nut and wrench
.
第 6 页

Accessory list for the installation of tail pipe. 18. Put the fiber exhaust into the tail fuselage and lock it
with screws .
16.Put the tail pipe to the fuselage from the tail fuselage. 19. Fix the tail pipe through assembly the 3mm ply tail
pipe frame, see pictures below .
17. Lockpipe socket to the tail pipe with schrews and nut,
and fix the side of pipe socket to the fuselage asbelow . Accessory list for the installation of plane nose .
第 7 页

20.Assemble the nose frame to the the fuselage with
screws and nuts. Accessory list for the installation of retract system .
21.Put the plane nose to the fuselageuntil they fit very
well, assemble the antena to the plane nose throught the
threaded rod .
23.Install the gear door servo to appropriate position in
the fuselage, connect the fiber horns in the gear doors to
the servo arms with the linkage and lock each side with
screws and nut.
22.The plane Nose assembled finished .
24. Assemble the main landing gear to appropriate
position into the fuselage with screws, install the wheels
to the landing gear.
第 8 页

25.Make sure the gears can be completely put the gear
down and retract the gear up. Accessory list for the installation of fuel tanks to fuselages.
26. Make sure the gears can be completely retracted
during work .
28.Assemble the fuel tank 1 to the nose fuselage, and
connect the main fuselage to the nose fuselage with screws
.
27. Put the nose gear into the fuselage and assemble it
into the fuselage . 29.Assemble the fuselages together tightly .
第 9 页

30.Assemble the other two fuel tanks to the main fuselage .
31.When you need to add some accessories under the
cockpit, please remove the nose and pull the steel
wires.
32. Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
33. Check all the datas well. make sure all sections
glue tightly. Otherwise if coming off during flights,
you'll lose control of your airplane which leads to
accidents!
34.C.G: Never fly before checking the CG's required position. Never fly the model without well balancing.
第 10 页

35.The picture after the F16 assembly .