Top RC Model Sport Jet Odyssey User manual

第 1 页

第 2 页

第 3 页

Accessory list for the coming installation steps.
3. Fix the servo trays to the wings with screws.
1. Apply AB glue to the slots in the ailerons, flaps and
assemble the horns into them.
4. The sketch map of the outgoing lines for servos and
retracts.
2. Epoxy the wood block to appropriate position on the servo
tray, Install the servo to the servo tray as below.
5. Assemble the clevis to the push rod .
第 4 页

6. Connect the horn to the servo arm with screw.
9. Assemble the wheel cover to the landing gear.
7. Prepare the main retracts to be assembled to the wing.
Accessory list for the coming installation steps.
8. Assemble the main retracts to the wing with screws.
10.Assemble the servo to the stabilizer through the slots
on the stab root.
第 5 页

11.Apply instand type AB glue to the slots in the stab and
put the horns in it.Use tape around the slots during assemble
the horns to keep clean.
Accessory list for the coming installation steps.
12.Use a sharp knife to open a slot to let the servo arm come out.
14.Apply instand type AB glue to the slots in the rudder,
vertical fin.
13.Connect the fiber horns to the servo arms with the
linkage and locked each side with screws and locked nut.
15.Assemble the rudder to the vertical fin and make sure
it can move freely.
第 6 页

16.The sketch map of how the servo arms connect to the
horns.
19.Assemble the servo to the vertical fin with screws.
17.Assemble the horns to the slots in the rudder.
20.Connect the fiber horns to the servo arms with the
linkage and locked each side with screws.
18.Measure the deepth to confirm what the servo position
will be and open a small slot for the servo arm.
第 7 页

Accessory list for the coming installation steps.
23.Assemble the steering linkages.
21.Fix the hatch hinge to the clevis on the Alu sash with
screw.
24.Assemble the nose retract to the fuselage with screws.
22.Assemble the servo to the nose retract.
25.The picture when the nose gear assembley completely.
第 8 页

26.Ready for put the fuel tanks in the fuselage.
29.Fix the tail pipe to the fuselage with screws.
27.Put the fuel tanks in the fuselage.
30.Assemble the Turbine and tail pipe.
28.Put the tail pipe to the fuselage.
31.Fix the tail pipe to fuselage with screws.
第 9 页

32.Fix the two fuselage section together with screws.
Accessory list for the coming installation steps.
33.The sketch map of the connection for the fuel tanks.
35.Put the alu wing bolt into the fuselage.
34.Fix the interior cockpit into the fuselage.
36.Assemble the wing to the fuselage through the wing
bolt.
第 10 页

37.Fix the wing to fuselage with screws from the bottom of
the wing.
40.Put the fin bolt into the vertical fin.
38.Fix the wing with screws from the bottom of the wing.
41.Put the vertical fin to the fuselage.
39.Glue the fin bolt.
42.Fix the vertical fin with screws.
第 11 页

43. Put the stab into the fuselage through stab tubes.
44.Fix the stab to fuselage with screws.
55.The photo when the model assemble completely.
第 12 页

56. Adjust the travel of each control surface to the values in
the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
57. Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
58.Check all the datas well. make sure all sections glue
tightly. Otherwise if coming off during flights, you'll lose
control of your airplane which leads to accidents!
59.C.G: Never fly before checking the CG's required
position. Never fly the model without well balancing.
第 13 页

第 14 页