Top RC Model Sport Jet Aspire ARF User manual

TopRCModel-USA.com

TopRCModel-USA.com

TopRCModel-USA.com

Accessory list for the coming installation steps.
3. Fix the servo trays to the wings with screws.
1. Apply AB glue to the slots in the ailerons, flaps and
assemble the horns into them.
4. Conntect the horn to the servo with the push rod and
secure them.
2. Epoxy the wood block to appropriate position on the servo
tray, Install the servo to the servo tray as below.
5. Assemble the wheel and oleo strut to the retract.
第 4 页

6. Fix the main retracts and wheel covers with screws.
9. Apply marking tape around the wing bafflers to keep
the wing not get dirty when glue the bafflers in the wings.
7. The picture when the gear down.
Accessory list for the coming installation steps.
8. The sketch map of how the wing baffler installation.
10.Assemble the servo to the stabilizer through the slots
on the stab root.
第 5 页

11. Use steel ruler to measure the length where the stab
servo will install inside the stab.
14.Apply marking tape around the horn to keep clean
when glue the horn in the elevator and connect it to the
servo arm.
12.Measure the same length on the bottom of the stab, mark
it and trim a slot for the stab servo arm.
Accessory list for the coming installation steps.
13.Assemble the stab servo to the stab with screws and screw
driver.
15.Apply instand type AB glue to the slots in the rudder,
vertical fin, assemble the rudder to the vertical fin with
hinges.
第 6 页

16.The sketch map of how the servo arms connect to the
horns.
19.Measure the same length on the vertical fin, mark it
and trim a slot for the rudder servo arm.
17.The processes for assembling the rudder servo.
20.Assemble the rudder servo to the vertical fin with
screws and screw driver.
18.Use steel ruler to measure the length where the rudder
servo will install inside the vertical fin.
21.Apply marking tape around the horn of rudder, glue
the horn in the rudder and connect the horn to the
rudder servo arm.
第 7 页

Accessory list for the coming installation steps.
24.Assemble the nose gear servo to the nose retract.
22.Connect the nose gear door with screw.
25.Assemble the steering linkages.
23.Connect the nose gear door with screw.
26.Assemble the nose retract to the fuselage with screws.
第 8 页

27.Put the tail pipe into the fuselage.
30.Fix the tail pipe to the fuselage with screws.
28.Assemble the turbine engine.
31.The sketch map of the connection for the fuel tanks.
29.Drill holes to appropriate position in the fuselage and
assemble the turbine engine to it with screws.
32.Install the bottom hatch to the fuselage with screws.
第 9 页

33.Assemble the fuel tank.
36.Fix the fuselages together with screws.
34.Put the fuel tank into the fuselage.
37.Put the plywood plate in the fuselage.
35.Put the two parts fuselage together.
Accessory list for the coming installation steps.
第 10 页

38. Put the wing tube through the fuselage.
Accessory list for the coming installation steps.
39.Assemble the wings to the fuselage through the wing
tube.
41.Glue the stabilizer tube to the stabalizer.
40.Lock the wing to the fuselage by screws from the bottom
of the fuselage.
42.The photo when the stabilizers ready.
第 11 页

43.Assemble the stabilizers to the fuselage.
45.Glue the vertical tubes to the vertical fin.
44.Lock the stabilizers to the fuselage by screws from the
top of the tail fuselage.
46.The photo when the vertical fin ready.
Accessory list for the coming installation steps.
47.Assemble the vertical fin to the fuselage, lock it with
screw from the hole in the tail fuselage as picture.
TopRCModel-USA.com
TopRCModel-USA.com
TopRCModel-USA.com

48.The photo when the model assemble completely.
49. Adjust the travel of each control surface to the values in
the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
50. Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
51.Check all the datas well. make sure all sections glue
tightly. Otherwise if coming off during flights, you'll lose
control of your airplane which leads to accidents!
52.C.G: Never fly before checking the CG's required
position. Never fly the model without well balancing.
第 13 页

第 14 页