Top RC Model Focke-Wulf Fw190A-8 User manual

TopRCModel-USA.com

TopRCModel-USA.com

TopRCModel-USA.com

Accessory list for the installation of aileron and flap.
3. Apply instand type AB glue to the holes in the aileron
and hinges. Epoxy the aileron to the wing.
1. Apply instand type AB glue to the slots in the flap and
pinned hinges.
4. Epoxy the aileron to the wing, Keep some space
between the trailing edge and the aileron to make sure it
can rotate smoothly.
2. Epoxy the flap to the wing, Keep some space between the
trailing edge and the flap to make sure it can rotate
smoothly.
5. Apply AB glue to the slots in the flaps and assemble the
horns into them.
TopRCModel-USA.com

6. Assemble the servos to the servo trays.
9. Connect the fiber horns in the aileron to the servo
arms with the linkage and lock each side with screws
and nut.
7. Assemble the servos to the servo trays.
10. Connect the fiber horns in the flap to the servo arms
with the linkage and lock each side with screws and nut.
8. Servos assembled ready.
Accessory list for the installation of elevator.
TopRCModel-USA.com

11. Apply instand type AB glue to the holes in the elevator
and round hinges, assemble the elevator to the stab.
14. Connect the fiber horns to the servo arms with the
linkage and lock each side with screws and nut.
12. Picture of the elevator assembled ready.
Accessory list for the installation of rudder and tail gear.
13. Apply AB glue to the slots in the elevator and assemble
the horns into them.
15. Apply instand type AB glue to the holes in the rudder
and assemble the rudder to the tail fin.
TopRCModel-USA.com

16.Picture of the rudder install ready, make sure it can
rotate smoothly.
19. Connect the arm of the tail landing gear with steel
wire.
17. Assemble the air cylinder to the tail fuselage.
20. Drill a small hole to appropriate possition in the
fuselage,connect the rudder to the servo in the fuselage
via steel wire.
18. Fix the air cylinder to the tail fuselage.
21. The photo when the rudder and tail wheel connect to
the servo in the fuselage via steel wires.
TopRCModel-USA.com

Accessory list for the installation of main retracts
24. Assemble the wheel cover to the oleo struts with
screws.
22. Install the main retracts to the wing with screws.
Accessory list for the installation of fuel tank and air
tank.
23. Glue the plies to the ring brackets on the oleo strut.
25. Assemble the air tank and fuel tank to appropriate
position in the fuselage, assemble the switch valve to the
servo too.
TopRCModel-USA.com

26. Assemble the air tubes to the switch valve.
28. Assemble the drop tanks to the fuselage.
27. Assemble the air tube to the air tank.
29. Assemble the engine to the engine mount.
Accessory list for the installation of drop tank and
engine.
30.The datas of the cowling.
TopRCModel-USA.com

31.Assemble the cowling to the fuselage, fix the propeller
and spinner to the engine.
33. Fixing the stab with screws from bottom of the
stab.
Accessory list for the installation of fixing the wing and
stab.
34. Assemble the canopy to the fuselage.
32. Fixing the main wing with plastic screws from
the fuselage.
TopRCModel-USA.com

35. Phones when the model assembled completely.
36. Phones when the model assembled completely.
第 11 页

37.Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
38.Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
39.Check all the datas well. make sure all sections glue tightly. Otherwise if coming off during flights, you'll lose control of
your airplane which leads to accidents!
40.C.G: Never fly before checking the CG's required position. Never fly the model without well balancing.
第 12 页

TopRCModel-USA.com