Topcom DIABLO 103 User manual

DIABLO 100/TWIN/
TRIPLE/QUATTRO
USER GUIDE
1.2
Important
To use ‘Caller ID’ (display caller), this service has to be activated on your phone line.
Normally you need a separate subscription from your telephone company to activate this
function. If you don’t have the Caller ID function on your phone line, the incoming telephone
numbers will NOT be shown on the display of your telephone.
To be connected to the public analogue telephone network.
The CE symbol indicates that the unit complies with the essential
requirements of the R&TTE directive.
The features described in this manual are published with reservation to modifications.
This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC.
The Declaration of conformity can be found on :
http://www.topcom.net/support/cedeclarations.php

7
4
2 5 8 0
3
6
9
1
R/INT
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
M1
12
7
3 8 1
5
13
10
2
11
4
Diablo
100
6
9
2Topcom Diablo 100/Twin/Triple/Quattro
Topcom Diablo 100/Twin/Triple/Quattro
Safety Instructions • Only use the charger plug supplied. Do not use other chargers, as this may damage the battery
cells.
• Only insert rechargeable batteries of the same type. Never use ordinary, non-rechargeable
batteries. Insert rechargeable batteries so they connect to the right poles (indicated in the battery compartment of the handset).
• Do not touch the charger and plug contacts with sharp or metal objects. • The operation of some medical devices may be affected. • The handset may cause an unpleasant buzzing sound in hearing aids. • Do not place the basic unit in a damp room or at a distance of less than 1.5 m away from a water
source. Keep water away from the handset.
• Do not use the telephone in environments where there is a risk of explosions. • Dispose of the batteries and maintain the telephone in an environment-friendly manner. • As this telephone cannot be used in case of a power cut, you should use a mains-independent
telephone for emergency calls, e.g. a mobile phone.
• This telephone uses rechargable batteries. You have to dispose of the batteries in an environment
friendly manner according to your country regulations.
Disposal of the device (environment)
At the end of the product lifecycle, you should not throw this product into the normal household garbage but bring the product to a collection point for the recycling of electrical and electronic equipments. The symbol on the product, user guide and/or box indicate this. Some of the product materials can be re-used if you bring them to a recycling point. By re-
using some parts or raw materials from used products you make an important contribution to the protection of the environment. Please contact your local authorities in case you need more information on the collection points in your area.
Cleaning Clean the telephone with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents. 1 Buttons (see folding page for the picture) 1. Numerical buttons 2. Off -hook button 3. Redial / Pause button 4. Flash R/ INT 5. Direct memory button M1 6. Paging button (to retrieve the handset) 7. Mute button 8. On hook button 9. Charge indicator/ On line (LED) 10. Call log/Scroll Up / 11. Scroll Down 12. Key lock 13. Program/Memory button /
/P

TopcomDiablo 100/Twin/Triple/Quattro 3
TopcomDiablo 100/Twin/Triple/Quattro
ENGLISH
2Display
3 Installation
•Plugone end ofthe phone cable into the phone unit and the other end into the telephone line wall
socket. ÎConnect the small plugofthe AC adaptor to the phone and the other end ofthe adapter
cable to the electric socket.
• Insert 2rechargeable batteries (AAA) inside the battery compartment ofthe handset..
Put the handset on the base unit. The red Charge LED will lit as longas the handset is on the base.
Charge the handset for aperiod of24 hours before usingthe handset for the first time. To extend the
battery life time, discharge the batteries completely fromtime to time. As soon as the handset emits a
warningtone or when the battery icon is empty, you have to put it backon the base unit for charging.
You are online
INT = Internal communication
EXT = External communication
There are more digits on the left
Newnumbers in call list There are more digits on the right
Rechargeable battery level indicator Program mode
The antennaindicates the quality of
reception
The antennablinks when the handset is
out ofrange!
There are newmessages in your voice
mail
Microphone is muted - x - x = handset number
Memory records are beingretrieved or
set up
hh:mm Time: hh = hours, mm = minutes
The keypad is locked Answered calls
Unanswered calls
Base
Telephone cord
Power cable
TEL.
SOCKET
Multi charger
Diablo
100
+-
-
+

4TopcomDiablo 100/Twin/Triple/Quattro
TopcomDiablo 100/Twin/Triple/Quattro
4Battery low indication
When the battery is empty, the handset no longer carries out operations. When abattery is completely
empty and you have put the handset on the base unit for ashort period oftime, the Battery symbol will
appear to be fully charged but this is actually not the case. The battery capacity will decrease rapidly.
We advise you to put the handset on the base unit for 12hrs so that it can be recharged completely:
Full battery Empty battery
When you are in the middle ofaconversation and the battery is almost empty, the handset will emit a
warningsignal. Place the handset on the base unit to charge.
5 Operation
5.1 Outgoing calls
5.1.1 Making a phone call or redialing the last number
Press the Off-hookbutton . You will hear the dial tone. ÎEnter the desired telephone number or
press the Redial key to dial out the number you last called. ÎPress the on-hookbutton when
you want to terminate the call.
5.1.2 Call setup with dial preparation
Enter the desired telephone number. An incorrect number can be corrected by means ofthe Mute
button. ÎPress the Off-hookbutton . The number will be dialled automatically. ÎPress the On-
hookbutton when you want to terminate the call.
5.1.3 Redial one of the last 5 numbers dialled
Press the Redial key . The number you last called appears on the display. Ifyou would like to dial one
ofthe last 5 numbers dialled, press the scroll keys afewtimes until the desired number appears
on the display. ÎPress the Off-hookkey . ÎThe number shown on the display is dialled
automatically. ÎAfter finishingyour call, press the On-hookkey to hangup.
5.2 Incoming calls
When acall comes in, the handset will start to ring. ÎPress the Off-hookbutton to answer the
incomingcall. To end the call press the On-hookbutton.
5.3 Programming memory numbers
You can program 10 indirect numbers (ofmax. 24 digits) in the phone’s memory.
Press the Memory button short. The first entry will be shown on the display ÎPress and hold the
Memory button until the -icon appears on the display. ÎEnter the location (0-9) where you want
to store the telephone number under. ÎEnter the telephone number you whish to store. ÎPress
the Memory button again to confirm. ÎYou will hear aconfirmation tone and the next entry will
appear. To leave the memory programming, press the on-hookbutton.
5.4 Calling amemory number
Press the Memory button ÎScroll with the Up/Down keys to the entry you want to dial (0-9).
ÎPress the Off-hookbutton . The memory number will be dialled automatically. ÎPress the On-
hookbutton to terminate the call.
If you wish to insert apause, press the Redial/Pause button on the location where
you want apause of 3 sec.
/P

TopcomDiablo 100/Twin/Triple/Quattro 5
TopcomDiablo 100/Twin/Triple/Quattro
ENGLISH
5.5 Direct access memory (Key 1,2,3 and M1)
The product has 3 locations (Key ‘1’, ‘2’ and ‘3’) where you can store anumber under and dial it by
pressingand holdingone ofthese keys in standby. The phone will automatically take the line and dial
the number which is stored under this key. The number stored under key ‘1’ can also be dialed out by
pressingthe ‘M1’-key shortly in standby.
5.5.1 Programing the direct memory keys
Press the Memory button short. Press and hold the Memory button until the -icon appears on
the display. Press and hold one ofthe 3 direct memory keys (Key 1,2or 3) where you want to store the
number under until ‘Sx - _’ appears. ÎEnter the telephone number you whish to store. ÎPress
the Memory button again to confirm. ÎYou will hear aconfirmation tone and the next entry will
appear. To leave the direct memory programming, press the On-hookbutton .
5.6 Mute function
It is possible to deactivate the microphone duringaconversation. Nowyou can speak openly without
beingheard by your correspondent. Press the Mute button duringaconversation. to deactivate or
activate the microphone.
5.7 Setting the volume
Duringaconversation you can set the volume by pressingthe scroll button . You can set the
volume between 1-5.
5.8 Paging
When you press the Pagingbutton on the base unit, the handset emits aringingsignal for 20 seconds.
This signal helps you find alost handset. Press any key to stop the ringingon all handsets.
5.9 Flash button (R)
When you press the Rbutton, also called flash or recall, the unit generates aline interruption (of100 ms
or 250 ms). It gives you the possibility to use the special services ofyour telephone provider and/or to
transfer calls when you have atelephone exchange. You can change the flash time ifneeded (See
“Settingthe Flash time” on page6).
5.10 Programming procedure
You can change the ringmelodie, volume, day, time etc... by goinginto the program procedure: To go
into the program procedure you have to press and hold the Program button until the icon starts to
flash. ÎPress the Program button again to change the first setting. Each time you press the Program
button you will confirmthe previous settingand jump to the next setting:
External ring volume/melody Î Internal ring volume/melody Î Date/time setting Î
Dial mode setting
Î Flash time setting Î Base ring volume/melody
5.10.1 Handset External melody and volume
Press and hold the Program button until the icon starts to flash. ÎPress the Program button
again, the external melody is heard and the EXT-icon is flashing. ÎSelect the desired melody (1-5)
by enteringanumber (1 - 5). ÎUse the scroll keys to select the desired volume (Off or 1-5) Î
Press again to confirmthe settingand to go to the next settingbelow.
5.10.2 Handset Internal melody and volume
The internal melody is heard and the INT-icon is flashing. ÎSelect the desired melody (1-5) by
enteringanumber (1 - 5). ÎUse the scroll keys to select the desired volume (Off or 1-5) Î
Press again to confirmthe settingand to go to the next settingbelow.

6TopcomDiablo 100/Twin/Triple/Quattro
TopcomDiablo 100/Twin/Triple/Quattro
5.10.3 Date time setting
After settingthe internal ringmelody and volume you can set the date and time:
DD-MM HH:MM (DD= day, MM=month, HH=houre and MM=minutes)
Enter the date and time usingthe number key. The flashingcursor can be moved by the scroll keys
.ÎPress again to confirmthe settingand to go to the next settingbelow.
5.10.4 Setting the Dial mode
After settingthe date/time you can set the dial mode. There are two types ofdiallingmode:
- 1 - DTMF/Tone dialling(the most common) (default)
OR
- 2 - Pulse dialling(for older installations)
Press ‘1’ or ‘2’ and press again to confirmthe settingand to go to the next settingbelow.
5.10.5 Setting the Flash time
After settingthe Dial mode you can set the flash time. There are two flash times:
- 1 - 100ms
OR
- 2 - 250 ms
Press ‘1’ or ‘2’ and press again to confirmthe settingand to go to the next settingbelow.
5.10.6 Base melody and volume
The base ringer is heard. ÎSelect the desired melody (1-5) by enteringanumber (1 - 5). ÎUse
the scroll keys to select the desired volume (Off or 1-5) ÎPress again to confirmthe setting
and to go backto standby.
5.11 Keypad lock
When the keypad is locked, pressingany key will have no effect duringstandby (except holdingthe
key).
Press and hold the key. Îappears on the display and the keypad is locked. ÎPress twice
the key again to un-lockthe keypad
6Caller-ID function (CLIP)
The TopcomDiablo displays the telephone numbers ofincomingcalls. This function is only possible if
you are subscribed to atelephone operator that provides this service. Contact your telephone provider
for more information. When you receive acall, the numbers are saved in aCall list. This list can hold 10
telephone numbers (each ofmax. 20 digits). Ifthe number is longer then 12digits, you can press the
program key to showthe other digits!
6.1 New calls
When you’ve received anewunanswered call, the CLIP symbol will blinkon the display.
6.2 Consulting the Call list
Press the Call Logbutton . The last received call is shown on the display. Ifthe list is empty, ‘----------
’ is shown on the display. For answered calls the -icon appears and unanswered calls the -icon
appears ÎPress the program key to showthe other digits (iflonger then 12) or to showthe date
and time. ÎUse the scroll keys to scroll to the previous call. When you reach the top or bottom
ofthe list an error tone will be sounded ÎYou can leave the Call list by pressingthe on-hook
button.
6.3 Calling anumber fromthe Call list
Scroll through the Call list until the desired number is shown on the display. ÎPress the Off-hook
button . The number will be dialled automatically.

TopcomDiablo 100/Twin/Triple/Quattro 7
TopcomDiablo 100/Twin/Triple/Quattro
ENGLISH
6.4 Erasing one or all number fromthe Call list
Scroll through the Call list until the desired number is shown on the display. ÎPress the Mute button
short to erase the current entry or press and hold the Mute button for 3 sec. to erase the compleet
call list.
6.5 Store anumber fromthe call log into the memory
Scroll through the Call list until the desired number is shown on the display. ÎPress and program
button for 3 sec. ÎThe memory will be shown and you can scroll through it with the scroll keys
to see which entry is still empty (0-9) ÎEnter the memory location (0-9) where you want to store
the number. ÎEdit the number ifneeded and press the program button again to confirmand to go
backto standby.
7 Register/de-register ahandset
7.1 Register to aTopcomDiablo base
You can subscribe 5 handsets to one base unit. By default, each handset is subscribed on the base unit
upon delivery.
You only need to subscribe the handset if:
• The handset subscription has been removed fromthe base unit (e.g. for reinitialisation)
•You want to subscribe adifferent handset to this base unit.
The belowprocedure is only applicable to aTopcomDiablo handset and base unit!!
Keep the Pagingkey on the base unit pressed for 10 seconds until the Line/Charge indicator
on the base unit begins to blinkrapidly. The Line/Charge indicator will blinkrapidly for one minute.
Duringthis minute, the base unit is in register mode and you must do the followingto subscribe the
handset:
Press and hold the Program key for 6sec until there is a‘-’ scrollingon the screen fromleft to right.
The handset is nowsearchingfor the base. When abase is found the handset will askto enter the pin-
code ‘P1-_’. Enter the base pin code (0000). Ifthe pin is wrong, the handset will restart the searchingfor
the base. ÎWhen the handset is registered, it will showthe handset number followed by the time.
8Call transfer and Intercombetween two handsets
8.1 Call transfer and conference call during an external call
Duringan external call, press and hold the INT key until INT appears . Press the number (1-5) ofthe
other handset. ÎThe other handset will start to ring:
– When the other handset takes the line you can talkinternally.
Ifyou hangup, the external line will be connected with the other handset.
Ifyou press the ‘#’-key you can talkwith the 2nd handset and external line at the same time
(conference call)
– Or press and hold the INT key again to return to the external call.
Press the On-hookbutton to end the call.
8.2 Internal call (intercom)
In standby press and hold the INT key until INT appears . Enter the number (1-5) ofthe other handset.
ÎThe other handset will start to ring. ÎIfthe other handset answers the call by pressingthe Off-
hookbutton you can talkinternally. ÎPress the On-hookbutton to end the call.
These functions only work when more then one handset (like aTwin/Triple/Quattro
version) is registered to the base!

8TopcomDiablo 100/Twin/Triple/Quattro
TopcomDiablo 100/Twin/Triple/Quattro
9 Troubleshooting
10 Technical Data
Range: up to 300 min open space
up to 50 min buildings
Diallingoptions: DTMF (tone) and Pulse
Batteries: 2x 1.2V, 550 mAh AAA Type NiMH rechargeable
Max. standby time: approx. 100 hours
Max. talktime: 10 hours
Ambient temperature: +5 °C to +45 °C
Permitted relative air humidity: 25 to 85 %
Power supply base adapter: 220/230V , 50 Hz
Memories 10 indirect with max. 25 digits
visit our website
www.topcom.net
U8006630
ProblemPossible cause Solution
No displayBatteries not charged Checkthe position ofthe
batteries
Recharge the batteries
No diallingtone Telephone cable not properly
connected
Checkthe connection ofthe
telephone cable
Volume ofconversation
partner too low
Adjust the volume duringthe
conversation by pressingthe
volume key
Handset ringer volume too lowAdjust the ringer volume
Not possible to dial anumber Wrongdial mode See “Settingthe Dial mode” on
page6