
Unfolding: Release the lock clamp
positioned at the seat bars A. Press the seat
bars down and out. The side frames will
slide apart. Press down the seat bars B.
You will hear a clicking sound. The rollator is
now locked in its open position.
Folding: Pull the strap on the seat Cand
press the side frames together. Lock the
clamp Dover the seat bars.
Carrying the rollator: The rollator must
not be carried by the seat strap or the brake
wires. Fold the rollator together as shown
on the illustration E. Carry the rollator by the
folded seat bars F.
Unfolding / folding
The parking brakes must be on before using
the seat. Push both brake handles
downwards until they lock A. Both rear
wheels are now locked. Sit with your back
towards the bag B.
Seat
37
2
Memory Function: Decide on the height of
the handlebars (see number scale).
Count visible holes at the back of the
handlebar tubes. Unscrew the lock wheel A.
Pull the tube Bout of the frame.
The fastening piece D will now follow the
handlebar tube. Move the fastening piece
Don the tube Bso the number of holes
corresponds to the number counted earlier.
Fit the red memory chip Eon the handlebar
tube in the rst available hole under the
fastening piece D.
Push the handlebar tube Bdown and into
the side frame Funtil the fastening piece
is locked. Screw the lock wheel Ahalf in.
Pull the handlebars G up until they stop,
and then tighten the lock wheel Aproperly.
From now on, when the handlebars are in
the lowest position, they will stop
in the pre-set position automatically when
pulled up.
Height adjusting: Unscrew the lock wheel
A(approx. 2 turns). Adjust the handlebar
tubes to a suitable height then pull them
slightly up and down Cuntil you hear a
clicking sound.
Tighten the lock wheel Aagain. Adjust both
handlebars to the same height by
comparing the number scale on each side.
It is recommended that the handlebars are
set to the same height as your wrists when
your arms are hanging alongside your body.
Handles / memory function
4
The bag holds up to 15 kilos and can be
washed gently at 60 °C.
Mounting: Apply the parking brake A.
Lift the bag onto the the carrying handles
B. When it is placed correctly, you will hear
a click. Ensure that the brake wire still runs
unrestrained along the frame C.
Removal: Apply the parking brake.
Place your hands towards the front of the
bag, on both sides. Lift the bag up while
pressing it slightly together.
Shopping bag
Edge guard / tilt function
8
9
Make sure the brakes are working before
each trip. Each brake handle Aworks on
each of the rear wheels. Do not drive or
push the rollator while the parking brakes
are in use! Parking brakes: Push both brake
handles Adown until they lock.
Both rear wheels are now locked.
Squeeze both brakes handles upwards to
release the parking brakes. Driving brakes:
Pull both brake handles Bupwards to
reduce speed. Do not use continuously while
the rollator is in motion.
Adjusting / checking: Loosen the nut C.
Tighten the brake wire Dwith the
adjustment screw E. Adjust the brake block
Fas close as possible to the inner drum
brake, and then tighten the nut C. Turn the
wheel around to check that the brake block
is not touching the wheel. Maintaining:
Clean the brake block Fand the brake
spring Gfrequently. The wheels and brakes
can be replaced if they are worn out
or damaged.
Brakes
5
If you want to remove the rear wheels for
transportation or replacement,
follow these instructions:
Removal: Loosen the brake lever.
Push down the red button on the hub A
and slide the wheel o the axle Bwhile still
pushing the button down.
Attachment: Loosen the brake lever.
Slide the wheel unto the axle B. Push the
wheel as far as possible inwards on the axle
to make the wheel snap onto the axle.
You will hear a “click” when the wheel is in
place. The wheel is securely fastened when
the axle is completely visible in the middle
of the hub C. Gently pull the wheel to check
that it is securely fastened to the axle.
After the new wheel has been applied to
the rollator, make sure that the brakes
are functioning properly.
Readjust them if necessary
(see section Brakes).
Rear wheels
6
TOPRO Ergo Grip oers ergonomic grip and
support surfaces. The front of the handles
gives you a better gripping position when
getting up from a chair or couch.
Always make sure that the parking brake is
locked when you do this. The hand grip also
oers extra support while standing.
When pushing the rollator, your hands
should always be kept in the original grip
position in order to make the best possible
use of the brakes
TOPRO Ergo Grip
Edge guard: The edge guards A, which
are in front of the rear wheels prevent the
rear wheels from catching on corners, door
frames etc.
Tilt function: To use the tilt function use
the front of the foot and press down on the
tilt pedal B, which is beside the rear wheel.
This helps to tilt the rollator over thresholds,
edges etc. Please note: Take care when
descending kerbs.
EN
SV