Toshiba RAC-PD0811CRU User manual

Safety Precautions
Operating Instructions
Installation Instructions
Care and Cleaning
Warning notices: Before using this product,
please read this manual carefully and keep
it for future reference.
The design and specications are subject to
change without prior notice for product
improvement. Consult with your dealer or
manufacturer for details.
O
perating In
s
C
C
areandCle
a
RAC-PD0811CRU
RAC-PD1011CRU
RAC-PD1211CRU
RAC-PD1411CRU
RAC-PD1411CWU
RAC-PD1411HRU
USER MANUAL
Portable Type
Room Air Conditioner
version B - 10 - 2017
Troubleshooting TipsTroubleshoo
t
Remote Control Operating
Instructions
us.toshiba-lifestyle.com

Page 2 User Manual
Read This Manual
Inside you’ll find many helpful hints on how to use and maintain your air conditioner properly.
Just a little preventive care on your part can save you a great deal of time and money
over the life of your air conditioner. You’ll find many answers to common problems in the
troubleshooting tips - you should be able to fix most of them quickly before calling service.
These instructions may not cover every possible condition of use, so common sense and
attention to safety is required when installing, operating and maintaining this product.
User Manual
CAUTION
Safety Precautions ...................................................................................................... 3
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or people who cannot
operate the air conditioning independently without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
• If the power cord needs to be replaced, please contact our consumer service and look
for an authorized technician.
• Electrical installation must be performed in accordance to national regulation standards
by qualied personnel only.
Operating Instructions ..............................................................................................
Installation Instructions .........................................................................................
Care and Cleaning ...................................................................................................
Troubleshooting Tips ..............................................................................................
Remote Control Operating Instructions ..........................................................
11
16
17
18
5

User Manual Page 3
SAFETY PRECAUTIONS
WARNING
WARNING: This symbol indicates the possibility of death or serious injury.
CAUTION: This symbol indicates the possibility of injury or damage to property.
Safety
Precautions
To prevent injury to the user or other people and property damage, the following instructions must
be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The
seriousness is classied by the following indications.
Please read through these instructions before you start the installation process.
Improper installation can cause damage to the unit, your personal property, and also
poses a personal safety hazard.
• Installation must be performed according to the installation instructions. Improper
installation can cause water leakage, electrical shock, or re.
• Use only the included accessories and parts, and specied tools for the installation.
Using non-standard parts can cause water leakage, electrical shock, re, and injury or
property damage.
• Make sure that the outlet you are using is grounded and has the appropriate voltage.
The power cord is equipped with a three-prong grounding plug to protect against
shock. Voltage information can be found on the side of the unit, behind the grille.
• Install the unit on a at, sturdy surface. Failure to do so could result in damage or
excessive noise and vibration.
• The unit must be kept free from obstruction to ensure proper functioning and to
mitigate safety hazards.
• DO NOT modify the length of the power cord or use an extension cord to power the
unit. DO NOT share a single outlet with other electrical appliances. Improper power
supply can cause re or electrical shock.
• DO NOT install your air conditioner in a wet room such as a bathroom or laundry room.
Exposure to water can cause electrical components to short circuit.
• DO NOT install the unit in a location that may be exposed to combustible gas, as this
could cause re.
• The unit has wheels to facilitate moving. Do not attempt to roll the unit across thick
carpet or over objects, as this could cause the unit to tip over.
• DO NOT operate a unit that has been dropped or damaged.
• Only use the included accessories and specied parts for installation. Using
nonstandard parts can cause water leakage, electrical shock, re, and injury or
property damage.

Page 4 User Manual
WARNING
Safety
Precautions
• DO NOT allow children to play with the air conditioner. Children must be supervised
around the unit at all times.
• If the air conditioner is knocked over during use, turn o the unit and unplug it
from the main power supply immediately. Visually inspect the unit to ensure there
is no damage. If you suspect the unit has been damaged, contact a technician or
customer service for assistance.
• In a thunderstorm, the unit should be turned o to avoid damage to the machine
due to lightning.
CAUTION
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
• If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
• Prior to cleaning or other maintenance, the appliance must be disconnected from the
supply mains.
• Do not install the appliance in a location that may be exposed to combustible gas. If
combustible gas accumulates around the unit, it may cause re.
• Do not run the power cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or appliances.
Arrange cord away from traffic area and where it will not be tripped over.
• To reduce the risk of fire or electric shock, do not use this air conditioner with any
solid-state speed control device.
• The appliance shall be installed in accordance with national wiring regulations.
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the authorized installer for installation of this unit.
• When there are signicant dierences between features or operation implied by the
remote control illustration and the actual functions described in the USER MANUAL,
the descriptions in the USER MANUAL shall prevail.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.)
batteries.

User Manual Page 5
Preparation
control panel
handle
(both sides)
horizontal louver
blade
(automatic swing)
Caster power plug socket
power cord buckle
bottom tray
drain outlet
power cord outlet
drain outlet
(only for pump
heating mode)
upper air filter
(behind the grille)
upper air intake
air outlet
lower air filter
lower air intake
drain outlet
Panel
Front Rear
Design and Compliance Notes
Design Notice:
In order to ensure the optimal performance of our products, the design specications of the unit and
remote control are subject to change without prior notice.
Energy Rating Information:
The Energy Rating for this unit is based on an installation using an unextended exhaust duct without
adaptors A or B (as shown in the Installation section of this manual).
Unit Temperature Range:
Mode Temperature Range
Cool 17°C ~ 35°C (62°F ~ 95°F)
Dry 13°C ~ 35°C (55°F ~ 95°F)
Heat (heat pump mode) 5°C ~ 30°C (41°F ~ 86°F)
Heat (electrical heat mode) ≤ 30°C (86°F)
Exhaust Hose Installation:
The exhaust hose and adaptor must be installed or removed in accordance with the usage mode.
For COOL, HEAT (heat pump type) or AUTO mode, exhaust hose must be installed.
For FAN, DEHUMIDIFY or HEAT (electrical heat type) exhaust hose must be removed.
OPERATING INSTRUCTIONS
Operating
Instructions

Page 6 User Manual
and Features
Operating
Instructions
Control Panel Features
Swing Button
Used to initiate the Auto Swing feature. When the
operation is ON, pressing the SWING button can
stop the louver at the desired angle.
Timer button
Used to initiate the AUTO ON start time and
AUTO OFF stop time program, in conjuction with
the Up ( ) and Down ( ) buttons. The timer
on or off light will illuminate depending on the
selected setting.
Fan button
Controls the fan speed. Press to control the fan
speed in four steps - LOW, MID, HIGH and AUTO.
The selected fan speed light (except AUTO) will
illuminate. When AUTO is selected, no lights will
illuminate.
Mode button
Selects the desired operating mode. Each time
you press the button, a mode is selected in a
sequence that goes from AUTO, COOL, DRY,
FAN and HEAT (cooling only models excluded).
The mode light illuminates and indicates the
selected mode.
Up ( ) and Down ( ) buttons
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F increments in
a range of 17°C/62°F to 30°C/86°F or the TIMER
setting in a range of 0 ~ 24hrs.
NOTE
Press the FAN button for 3 seconds to initiate
the ION feature, which helps remove pollen
and impurities from the air, and trap them in
the filter. Press it for 3 seconds again to turn
off the ION feature.
Power button
Power switch on/o.
Sleep (Eco)/Filter button
Used to initiate the SLEEP/ECO operation.
NOTE
The control is capable of displaying
temperature in degrees Fahrenheit or
degrees Celsius. To convert from one to
the other, press and hold the Up and Down
buttons at the same time for 3 seconds.
Timer
Button
Swing
Button
Power
Button
Sleep/Eco
Button
Fan
Button
Up ( ) and Down ( )
Buttons
Mode
Button
LED Display Wi-Fi Indicator Light
(Wi-Fi models only)

User Manual Page 7
Operating
Instructions
WI-FI Function
(Available on Wi-Fi models only)
With the unit ON, press the VENT ANGLE/
SWING button for 3 seconds to initiate the
Wireless Connection mode. The LED display
will display “AP” to indicate the wireless access
point is available. Follow the instructions on the
Wi-Fi setup manual and the latest app version
available for your phone operating system. If
the connection is successful, the unit will exit
“AP” mode automatically and the Wi-Fi indicator
light will illuminate. If connection is unsuccessful
within 8 minutes, the unit exits “AP” mode and
returns to regular operation.
If the Wi-Fi function is ON and there is a need to
turn it o, press and hold the VENT ANGLE/SWING
button and DOWN (-) button simultaneously
for 3 seconds. The display will show “OFF” for
3 seconds and the Wi-Fi function will become
inactive. To turn it back on, press and hold the
VENT ANGLE/SWING button and UP (+) button
simultaneously for 3 seconds. The display will
show “ON” for 3 seconds. When you restart the
wireless functions, it will take a period of time to
connect to the network automatically. Always be
sure your wireless connection is working properly
and there is a valid internet connection for Wi-Fi
functionality to work.
NOTE
When one of the above malfunctions
occurs, turn off the unit and check for
any obstructions. Restart the Unit. If the
malfunction persists, turn off the unit
and unplug the power cord. Contact the
manufacturer or its service agents or a similar
qualified person for service.
Control Panel Features (cont.)
LED display
Shows the set temperature in °C (Degrees Celsius)
or °F (Degrees Fahrenheit) and the Auto-timer
settings. While on DRY and FAN modes, it shows
the room temperature.
Shows Error codes and protection code:
E1 - Room temperature sensor error.
E2 - Evaporator temperature sensor error.
E3 - Condenser temperature sensor error (select
models).
E4 - Display panel communication error.
P1 - Bottom tray is full - Connect the drain
hose and drain the collected water away.
If protection code repeats, call for service.
Timer
Button
Swing
Button
Power
Button
Sleep/Eco
Button
Fan
Button
Up ( ) and Down ( )
Buttons
Mode
Button
LED Display Wi-Fi Indicator Light
(Wi-Fi models only)

Page 8 User Manual
Operating Instructions
COOL operation
• Press the“MODE”button until the “COOL”
indicator light comes on.
• Press the ADJUST buttons Up ( ) or
Down ( ) to select your desired room
temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F.
• Press the“FAN SPEED” button to choose the fan
speed.
HEAT operation
(available on HEAT models only)
• Press the “MODE” button until the “ ”
indicator light comes on.
• Press the ADJUST buttons Up ( ) or
Down ( ) to select your desired room
temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F.
• Press the “FAN SPEED” button to choose the fan
speed. For some models, the fan speed cannot
be adjusted while in HEAT mode.
DRY operation
• Press the “MODE” button until the “DRY”
indicator light comes on.
• While in this mode, you cannot select a fan
speed or adjust the temperature. The fan
motor operates at LOW speed.
• Keep windows and doors closed for the best
dehumidifying eect.
• Do not connect the duct to a window.
AUTO operation
• When you set the air conditioner to AUTO mode,
it will automatically select cooling, heating
(cooling only models excluded), or fan only
operation depending on what temperature you
have selected and the current room temperature.
• The air conditioner will control room
temperature automatically according to the
temperature point set by you.
• Under AUTO mode, you cannot select the fan
speed.
FAN operation
• Press the“MODE” button until the ”FAN“
indicator light comes on.
• Press the“FAN SPEED” button to choose the fan
speed. The temperature cannot be adjusted.
• Do not connect the duct to a window.
TIMER operation
• When the unit is on, pressing the Timer button
will initiate the Auto-o stop program. The TIMER
OFF indicator light illuminates. Press the Up or
Down button to select the desired time. Press the
TIMER button again within 5 seconds. The Auto-
on start program is initiated and the TIMER ON
indicator light illuminates. Press the Up or Down
button to select the desired Auto-on start time.
• When the unit is o, press the Timer button to
initiate the Auto-on start program. Pressing it
again within ve seconds will initiate the Auto-
o stop program.
• Press or hold the Up or Down button to
change the Auto time by 0.5 hour increments,
up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the
time remaining until start.
• The system will automatically revert back to
display the previous temperature setting if there
is no operation within 5 seconds.
• Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timer program.
• Should a malfunction occur, the Auto Start/Stop
timed program will also be cancelled.
SLEEP/ECO operation
Pressing this button will increase (during cooling
operation) or decrease (during heating operation,
applicable models) 1°C/1°F after 30 minutes.
The temperature will again increase (cooling)
or decrease (heating) by another 1°C/1°F after
an additional 30 minutes. This new temperature
will be maintained for 7 hours before returning
to the originally selected temperature. This ends
the Sleep/Eco mode and the unit will continue to
operate as originally programmed.
NOTE
This feature is unavailabe in FAN or DRY mode.
Operating
Instructions

User Manual Page 9
Operating
Instructions
Other Features
AUTO-RESTART
If the unit shuts o unexpectedly due to a power outage, it will restart with the previously set function
automatically when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it cannot be restarted until 3 minutes time has elapsed. This is to protect the
unit. Operation will automatically resume after 3 minutes.
AIRFLOW DIRECTION ADJUSTMENT
The louver can be adjusted automatically. Adjust the airow direction automatically.
• When the Power is ON, the louver opens fully.
• Press the SWING button on the panel or remote controller to initiate the Auto Swing feature. The
louver willl swing up and down automatically.
• Please do not adjust the louver manually.
WATER DRAINAGE
• During dehumidifying modes, remove the upper drain plug
from the back of the unit and install the drain connector (5/8”
universal female mender) with 3/4” hose (locally purchased).
For models without drain connector, just attach the drain hose
to the hole. Place the open end of the hose directly over the
drain area in your basement oor.
Remove the
upper drain plug
Continuous
drain hose
¥
• During heating mode, remove the lower drain plug from the
back of the unit and install the drain connector (5/8” universal
female mender) with 3/4” hose (locally purchased). For models
without drain connector, just attach the drain hose to the
hole. Place the open end of the hose adaptor directly over the
drain area in your basement oor.
Units with
Pump Only
¥
drain hose
adaptor
Continuous
drain hose
Remove
the lower
drain plug

Page 10 User Manual
NOTE
¥
delivery lift <1.8m
drain
hose
adaptor
drain
hose
adaptor
X
Make sure the hose is secure so there are no leaks. Direct the hose toward the drain, making sure that
there are no kinks that will impede water ow. Place the end of the hose into the drain and make sure
the end of the hose is directed downward to let the water ow smoothly. (See Figs with ).
Installation not recommended. (See Figs with X). When the continuous drain hose is not used,
ensure that the corresponding drain plug and knob are installed rmly to prevent leakage.
WATER DRAINAGE (cont.)
• When the water level of the bottom tray reaches a
predetermined level, the unit beeps 8 times. The digital display
shows “P1.” At this time the air conditioning/dehumidication
process will immediately stop. However, the fan motor will
continue to operate (this is normal). Carefully move the unit
to a drain location, remove the bottom drain plug and let the
water drain away. Reinstall the bottom drain plug and restart
the machine until the “P1” symbol disappears. If the error
repeats, call for service.
NOTE
Be sure to reinstall the bottom drain plug rmly to prevent
leakage before using the unit.
Units with
Pump Only
Operating
Instructions