Toshiba SD-6100KU2 User manual

DVD PLAYER
SD-6100KU
SD-K980KU
DIGITAL VIDEO
2
11
16
19
29
36
Introduction
Connections
Basic playback
Advanced playback
Function setup
Others
®
© 2008 Toshiba Corporation
Owner’sRecord
The model number and serial number are on the back of
your DVD Player. Record these numbers in the spaces
below.Refertothesenumberswhenever you communicate
with yourToshiba dealer about this DVD Player.
Modelnumber:
Serialnumber:
OWNER’S MANUAL

2
Introduction
SAFETYPRECAUTIONS
WARNING: TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT
OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CAUTION: TOPREVENTELECTRICSHOCK,MATCHWIDE BLADE OF PLUGTOWIDESLOTOF ACPOWEROUTLET,
THEN FULLY INSERT.
WARNING: The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquid, such as
vases, shall be placed on the apparatus.
CAUTION: This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for future
reference. Should the unit require maintenance, contact an authorized service location.
Use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Toshiba, or parties authorized by Toshiba,
could void the user authority to operate the equipment.
The lightning flash with an arrowhead symbol, within the
equilateraltriangle,isintendedtoalerttheusertothepresence
of uninsulated "dangerous voltage" within the product's
enclosurethatmaybeofsufficientmagnitudetoconstitutea
risk of electric shock to persons.
Theexclamationpointwithintheequilateraltriangleisintended
to alert the user to the presence of important operating and
maintenance(servicing)instructionsinthisowner’smanual.
CLASS 1
LASER PRODUCT
Warnings: • The main plug is used as disconnect device and it should remain readily operable during intended used.
In order to disconnect the apparatus from the mains completely, the main plug should be disconnected
from the mains socket outlet completely.
• Minimum 10 cm (4 inches) distances around the apparatus for sufficient ventilations.
• Theventilationshould not be impeded by covering the ventilation openings with items such asnewspaper,
table-cloths, curtains, etc.
• No naked flame sources such as lighted candles should be placed on the apparatus.
• The use of apparatus in moderate climates.
The symbol for Class (Double lnsulation)
CAUTION:VISIBLE LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM.
AVIS
WARNING:TO REDUCETHE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICINGTO QUALIFIED SERVICE PERSONNEL.

3
Introduction
IMPORTANTSAFETYINSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong.The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Portable Cart Warning
15. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or
electric shock.
16. Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with
liquid, or candles on top of the unit.
17. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.
18. Do not place anything on top of this unit.
19. Do not place the apparatus on amplifiers or equipment that may produce heat.
20. Never block or cover the slots or openings in the unit.
Never place the unit:
• on a bed, sofa, rug or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, buit-in cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the unit from overheating and to help maintain reliable operation.
21. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury
and apparatus malfunction.
22. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire.
23. During thunderstorms, do not touch the connecting cables or the apparatus.
24. Warning: To prevent spread of fire, keep candles or other open flames away from this product at all times.
ADDITIONALSAFETYINSTRUCTIONS
Location of the required label
The rating plate and the safety caution are
on the rear of the unit.

4
Introduction
Precautions
Notes on moisture condensation
Moisture condensation damages the DVD player. Please
read the following carefully.
Moisturecondensationoccurs,forexample,whenyoupour
a cold drink into a glass on a warm day. Drops of water
formonthe outside ofthe glass.Inthesameway, moisture
may condense on the optical pick-up lens inside this unit,
one of the most crucial internal parts of the DVD player.
Moisture condensation occurs during the following
cases.
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD player in a humid place.
Donotuse the DVDplayerwhenmoisturecondensation
may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player
willhavewarmed up and evaporatedanymoisture.Keep
the DVD player connected to the wall outlet and
moisture condensation will seldom occur.
Notes on handling
When shipping the DVD player, the original shipping
carton and packing materials come in handy. For
maximumprotection, repack theunit as itwas originally
packed at the factory. Take care not to give it a shock
or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD player.Do not leave rubber or plastic products
in contact with the DVD player for a long time.They will
leave marks on the finish.
Thetop and rearpanels of the DVDplayer may become
warm after a long period of use. This is not a
malfunction.
When the DVD player is not in use, be sure to remove
the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on
and use the DVD player occasionally.
Notes on locating
Place the DVD player on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand.The loaded disc may come off
the proper position and cause damage to the DVD
player.
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD
player away from theTV, radio, or VCR.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe.Use a dry cloth to wipe it
dry.
Do not use any type of solvent, such as thinners and
benzene, as they may damage the surface of the DVD
player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Inspection and Maintenance
This DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts become dirty
or worn down, the picture quality may be reduced. To
avoid reduction in picture quality, it is recommended that
regular inspection and maintenance (cleaning or parts
replacement)be performed every1,000 hours of use. For
further details, contact yournearestconsumer electronics
dealer.

5
Introduction
Notes on Discs
Playback side
DVD
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Structure of disc contents
Normally, DVDs are divided into titles, and the titles are
sub-dividedinto chapters.VIDEO CDs and audio CDs are
divided into tracks.
DVD
VIDEO CD/audio CD
Each title, chapter or track is assigned a number, which is
called “title number”, “chapter number” or “track number”
respectively.
There may be discs that do not have these numbers.
Notes on copyright
The unauthorized recording, use, distribution, or revision
of copyrighted materials including, without limitation,
television programs, videotapes, and DVDs, is prohibited
under the Copyright Laws of the United States and other
countries,andmaysubjectyoutociviland criminal liability.
Thisproduct incorporates copyright protection technology
that is protected by method claims of certain U.S.patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
On handling discs
Do not touch the playback side of the disc.
Do not attach paper or tape to discs.
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth.Always keep the disc clean.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Donot use any type of solventsuch as thinner, benzine,
commercially available cleaners or antistatic spray for
vinyl LPs.It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Track 1 Track 2 Track 3 Track 4 Track 5
VIDEO CD/audio CD

6
Introduction
DIGITAL VIDEO
SUPER VIDEO
• You cannot play discs other than those listed above.
• YoucannotplayDVD-RAMdiscsornon-standardizeddiscs,
etc., even if they may be labeled as above.
• This DVD player uses the NTSC color system, and cannot
playDVDsrecordedinanyothercolorsystem(PAL,SECAM,
etc.).
Because of problems and errors that can occur during the
creation of DVD and CD software and/or the manufacture of
DVD and CD discs,Toshiba cannot assure that this DVDplayer
willsuccessfullyplayeverydiscbearingtheDVD and CDlogos.
If you happen to experience any difficulty playing a DVD and/
orCDdisconthis DVDplayer,please contactToshiba Customer
Service.
isa trademarkofDVD Format/LogoLicensingCorporation.
Notes on Discs (continued)
DVDs
Disc Mark
Contents
Disc
Size Maximum
playback time
VIDEO
CDs
Approx. 4 hours
(single sided disc)
Approx.8 hours
(double sided disc)
Approx.80 minutes
(single sided disc)
Approx.160 minutes
(double sided disc)
Approx.74 minutes
Approx.20 minutes
8 cm
12 cm
8 cm
12 cm
Audio
+
video
(moving
pictures)
Audio
+
video
(moving
pictures)
Audio
CDs
Approx.74 minutes
Approx.20 minutes
8 cm
(CD
single)
12 cm
Audio
The following discs are also available.
DVD±R/±RW and DVD-ROM discs of DVD format
CD-R/CD-RWdiscsofCD-DA,Video CD,MP3,WMAor
JPEG format
Official DivX®Certified product
PlaysallversionsofDivX®video (including DivX®6) with
standard playback of DivX®media files
Some of these discs may be incompatible.
SUPER
VIDEO
CDs
DivX®
35 min.
10 min.
8 cm
12 cm
Audio
+
video
(moving
pictures)
Audio
+
video
(moving
pictures)
It depends on DivX
®
quality
8 cm
12 cm
About this owner’s manual
Thisowner’s manualexplainsthe basic instructions of this
DVD player. Some DVDs are produced in a manner that
allows specific or limited operation during playback. As
such, the DVD player may not respond to all operating
commands.This is not a defect in the DVD player.Refer
to instruction notes of discs.
“ ” may appear on the TV screen during operation.
A “ ” means that the operation is not permitted by the
DVD player or the disc.
Notes on region numbers
The region number of this DVD player is 1. If region
numbers, which stand for their playable area, are printed
on your DVD and you do not find or , disc
playback will not be allowed by the player. (In this case,
the DVD player will display a message on-screen).
On VIDEO CDs
This DVD player supports VIDEO CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.)You can enjoy two playback variations
depending on types of discs.
• VIDEOCD not equipped withPBC function (Version1.1)
Sound and movie can be played on this DVD player in
the same way as an audio CD.
• VIDEO CD equipped with PBC function (Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s manual
may not work with some discs.
Playable discs
This DVD player can play the following discs.

7
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS ........................... 2
IMPORTANT SAFETY INSTRUCTIONS .... 3
Precautions ............................................... 4
Notes on Discs .......................................... 5
Noteson region numbers ................................... 6
Table of Contents...................................... 7
Identification of Controls......................... 8
Frontpanel .......................................................... 8
Rearpanel .......................................................... 8
DVD display ........................................................ 8
Remotecontrol.................................................... 9
Loading batteries ............................................... 10
Operating with the remotecontrol ...................... 10
Connections
Connecting to aTV .................................. 11
Connectingto aTV............................................. 11
Connectingto aTV(Using the component video
jacks)................................................................. 11
Connectingto adisplay (Usinga HDMI
TM
cable)......... 12
Connecting to Optional Equipment ....... 13
Connecting to an amplifier equipped with a
Dolby®Digitaldecoder .........................................14
Connecting to an amplifier equipped with
Dolby Surround Pro Logic .............................. 14
Connecting to an amplifier equipped with a
DTS®decoder.................................................. 15
Connectingtoan amplifier equippedwith an MPEG2
audiodecoder .................................................. 15
Connecting to an amplifier equipped with a
digital audio input ........................................... 15
Basic playback
Playing a Disc.......................................... 16
Basic playback................................................ 16
Variable Speed Playback......................... 17
Playing in fast reverse or fast forward
directions ...................................................... 17
Playing frame by frame ................................... 17
Playing in slow-motion.................................... 17
Resuming playback from the same location .. 17
Locating a Desired Section ..................... 18
Locating a title using the top menu..................18
Locating a specific chapter or track ................ 18
Advanced playback
Accessinga SpecificLocation Directly ........... 19
Locatinga specifictitle/chapter/time ................... 19
Repeating a Specific Segment................. 20
Repeatinga specificsegment ............................ 20
Playing in a Varied Order......................... 20
Playing titles, chapters or tracks in a varied
order.................................................................. 20
Playing in a Favorite Order ...................... 21
Setting titles, chapters or tracks in a favorite
order.................................................................. 21
Zooming a Picture..................................... 22
Zooming a picture ............................................. 22
Selecting the Sound Enhancement
(E.A.M.) ...................................................... 22
Selecting the sound enhancement................... 22
Selecting the Picture Enhancement
(E.P.M.) ....................................................... 23
Selecting the picture enhancement.................. 23
Selecting Subtitles .................................... 23
Selecting a subtitle language ........................... 23
Selecting the Camera Angle...................... 24
Changing the camera angle............................. 24
Selecting a Language................................ 24
Selecting a playback audio setting................... 24
On-screen DisplayOperation .................... 25
On-screen display operation ............................ 25
Playing MP3/WMA Files ........................... 26
PlayingMP3/WMA files ...................................... 26
Viewing JPEG Files .................................. 27
Viewing JPEG files ............................................ 27
Viewinga thumbnailview ................................... 27
Playing DivX®/MPEG-4 Files .................... 28
Playing DivX®/MPEG-4files............................... 28
Function setup
Customizing the Function Settings ........ 29
Setting procedure ............................................... 29
Settingdetails..................................................... 29
Table of Languages................................... 35
Others
Before Calling Service Personnel ........... 36
Specifications ........................................... 37
Limited Warranty ...................................... 38

8
Introduction
Identification of Controls
See the page in for details.
16
16
16
10
16 8
12
HDMI indicator
16
HDMI SELECT
12
Front panel
12
HDMI OUT
jack 11
11
11
11
14
S-VIDEO
S-VIDEO OUT
jack
15
Power Cord
Rear panel
Chapter/Track number Indicator
The indicators vary depending on the kinds of discs you
play.
Multifunctional indicator (indicates
operating status or messages, etc.)
Bad disc
• During playback:
Example • During playback: Example • During playback: Example
Some discs may only
display chapter numbers. Some discs may only
display track numbers. Some discs may only display track numbers.
LOAD/CLOSE
No disc
OPENAudio CDVIDEO CDDVD VIDEO
DVD display

9
Introduction
* MENU button
Usethe MENU buttonto display themenu included on
manyDVDs.Tooperateamenu, followtheinstructions
in “Locating a title using the top menu.”
18
* RETURN button
Return to menu display forVCD (2.0) discs with menu.
16
HDMI button
19
22
23
24
17
18
17
18
18
20
19
21
29
12
16
19
17 23
24
16
16
18
1718
25
16
25 16
16 20
22
12
Remote control
Theinstructions in this manualdescribe the functions onthe remote control. Seethe page in for details.

10
Introduction
Open the cover.
Insert batteries (R03/AAA size).
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Caution
• Never throw batteries into a fire.
Notes
• Be sure to use R03/AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Do not mix different battery types or combine used batteries
with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• Ifthebatteries are dead or ifyouwillnotbeusingtheremote
control for a long time, remove the batteries to prevent
battery acid from leaking into the battery compartment.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
Distance: About7m(23feet)from thefrontoftheremote
sensor
Angle: About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD player
to a strong light source such as direct sunlight or
other illumination.If you do so, you may not be able
to operate the DVD player via the remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
player.
• Whenusingtheremotecontrol,pressthebuttonsatintervals
of about 1 second to ensure the correct mode of operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote control.
• Do not open the remote control.
• If the remote control is not going to be used for a long
time, remove the battery to avoid damage caused by
battery leakage corrosion.
2
Loading batteries
1
CAUTIONS:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
• Do not dispose of battery in fire; battery may explode or leak.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of
these batteries must be strictly followed.
Identification of Controls (continued)

11
Connections
Connections
Connecting to a TV
Connect the DVD player to yourTV.
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to yourTV, be sure to turn off the power and unplug both units from the wall outlet before making any
connections.
• Ifyourtelevisionsethasoneaudio input, connect the leftandrightaudiooutputsofthe DVDplayertoaY cableadapter(notsupplied)and
thenconnecttoyourTV.
• Connect the DVD player directly to yourTV. If you connect the DVD player to aVCR, TV/VCR combination or video selector, the playback
picturemaybedistortedasDVDs are copyprotected.
• Analog audio out will not have sound if DTS playback is selected.
Audio/Video cables (supplied)
S-Video cable (not supplied)
To 2ch AUDIO OUT
(R: red, L: white)
To VIDEO
OUT
(yellow)
Normal TV
To video
input
(yellow)
To audio
input
IftheTV has a S-video input, connect the DVDplayer
withanS-videocable.When using an S-video cable,
donotconnecttheyellowvideo cable and component
video cables (Y/PB/PR).
Connecting to aTV
Connecting to aTV (Using the component video jacks)
Audio cable
To audio input
ToY video
input
ToP
B
video
input
To P
R
video
input
To 2ch AUDIO OUT
(R:red, L:white)
Connections
• Makethefollowingsetting.
On-screen display Select: Page
“Off”,
“PCM” or
“Raw”
“DigitalOutput”
“VideoOutput” S-VIDEO
Component
P-Scan
HDMI
31
32
Interlaced outputs (ColorStream®)
Some TVs or monitors are equipped with component video inputs.
Connecting to these inputs allows you to enjoy higher quality
picture playback.
Actual labels for component video inputs may vary depending on
the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CB)
In some TVs or monitors, the color levels of the playback picture
may be reduced slightly or the tint may change. In such a case,
adjust the TV or monitor for optimum performance.
Progressive outputs (ColorStream Pro®)
Some TVs or monitors are equipped with component video inputs
that are capable of reproducing a progressively scanned video
signal. Connecting to these inputs allows you to view the highest
quality pictures with less flicker.
Consumers should note that not all high definition television sets
are fully compatible with this product and may cause artifacts to
be displayed in the picture. In case of 480 progressive scan picture
problems, it is recommended that the user switch the connection to
the “standard definition” output. If there are questions regarding our
TVsetcompatibilitywiththismodel 480p DVD player, please contact
ourCustomerServiceCenter.

12
Connections
About HDMI
HDMI(HighDefinitionMultimedia Interface) supports both video
andaudioonasingledigitalconnectionforusewithDVD players,
DTV, set-top boxes, and other AV devices.HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in
one specification. HDCP is used to protect digital content
transmitted and received by DVI-compliant or HDMI-compliant
displays.
HDMI has the capability to support standard, enhanced, or high-
definition video plus standard to multi-channel surround-sound
audio. HDMI features included uncompressed digital video, a
bandwidth of up to 2.2 gigabytes per second (with HDTV) signals),
one connector (instead of several cables and connectors), and
communication between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI licensing LLC.
Switching the output signal (interlaced / progressive)
using the remote control
Youcan temporarilyswitchtheoutputsignalforbetterpicture quality.
PressPROGRESSIVE buttonrepeatedlyonthe remote control to
selectVideoOutputtoP-Scanmode during stop.
IfyourTVdoesnot supporttheprogressive scanformat,thepicture
will appear scrambled or blank.To return to normal picture, press
PROGRESSIVEbuttonrepeatedly toselecttheComponent mode.
• Makethefollowingsetting.
On-screendisplay Select: Page
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet
beforemakinganyconnections.
• If youplacethe DVDplayernearatuner or radio,theradiobroadcast sound mightbedistorted.In thiscase,placethe DVDplayeraway from
the tuner and radio.
• The output sound of the DVD player has a wide dynamic range.Be sure to adjust the receiver’s volume to a moderate listening level.
Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn offtheamplifierbefore you connectordisconnecttheDVDplayer’spowercord.If you leavetheamplifierpower on,thespeakersmay
be damaged.
• Analog audio out will not have sound if DTS playback is selected.
• ColorStream®andColorStreamPro®areregisteredtrademarksofToshibaAmericaCousumerProductsL.L.C.
“PCM”or
“Raw”
“DigitalOutput”
Component
*P-Scan
(Progressive)
“VideoOutput”
* Only for TV equipped with component video
inputjackswhich supporttheprogressivescan.
31
32
480p, 720p, 1080i and 1080p are signals created with this
DVD Player from original 480i signal. The resolution of the
picture may not be increased even if they are selected.
HDMIindicator Video output signal
illuminates“•1080i” 1080i(interlaced)
illuminates“•720p” 720p(progressive)
illuminates“•480p” 480p(progressive)
Press
Press
Press
• Makethefollowingsetting.
On-screendisplay Select: Page
“PCM”
“DigitalOutput”
HDMI
“VideoOutput”
HDMI-compatible display
HDMI Cable
To HDMI
Output
Available output signals are below:
• Auto
• 480p (progressive)
• 720p (progressive)
• 1080i (interlaced)
• 1080p (progressive)
Switching the video quality (HDMI mode) using HDMI
button on the remote control or HDMI SELECT button
on the front panel.
PressHDMI buttonontheremote control orHDMI SELECT button
onthefront panel toreceiveasuitable videoqualityinSTOP mode.
Thevideoqualityis requiredtomatchyourTV havingHDMIfeature
and suitable quality. Please also check yourTV owner’s manual.
Press this button to change the output signals as below. See the
HDMIindicatorandselecttheappropriateoutputsignal.
illuminates“•1080p” 1080p(progressive)
31
32
Connecting to a display (Using a HDMITM cable)
Press
illuminates“• 480p, • 720p,
•1080i and • 1080p” Auto
Press

13
Connections
Connections
Notes
• Refer to the owner’s manual of the connectedTV as well.
• WhenyouconnecttheDVD playertoyourTV,besuretoturnoffthepowerandunplugbothunitsfromthewalloutletbeforemaking
anyconnections.
• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable.
• TheHDMIconnectoroutputsuncompresseddigitalvideo,as well as almost everykindofdigitalaudiothattheplayeriscompatible
with,includingDVD-Video,VideoCD/SuperVCD, CD, WMA and MP3.
• This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component you
have connected. Using a HDMI connection may result in unreliable signal transfers.
• Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with this
DVDplayer.
• When using HDMI cable, do not connect to other analog video outputs.
• No sound will be output from the HDMI cable if the digital out is not set to PCM.
• HDMI output is only available when theVideo Output is set to“HDMI”.Otherwise the HDMI button is invalid.
Content of the out
p
ut for each out
p
ut
j
ack is shown in the followin
g
tabl
e
and differ dependin
g
on the On-Screen Displa
y
Settin
g
:
"Video Output" HDMI Output HDMI Video Component S-Video
Setting Setting * Output Output Output Output
S-Video Invalid - Composite - S-Video
Component Invalid - Composite 480i -
(Interlaced)
P-Scan Invalid - Composite 480p -
(Progressive) 480p 480p Composite 480p -
HDMI 720p 720p - - -
1080i 1080i - - -
1080p 1080p - - -
* Settin
g
s for HDMI out
p
ut format are
p
erformed usin
g
the HDMI butto
n
on the remote control or HDMI SELECT button on the front panel.
Content of output for each output jackOn-Screen Display Setting
Notes
• DO NOTconnecttheCOAXIALDIGITAL AUDIOOUT jackoftheDVD player totheAC-3RFinputofaDolby Digital Receiver. This
input on your A/V Receiver is reserved for Laser disc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack
of the DVD player.
• ConnecttheCOAXIALDIGITALAUDIO OUT jackoftheDVDplayertothe“DIGITAL (COAXIAL)”inputofaReceiverorProcessor.
• Refer to the owner’s manual of the connected equipment as well.
• WhenyouconnecttheDVD playertootherequipment,besuretoturnoffthe powerandunplug all of the equipment from the wall
outlet before making any connections.
• The output sound of the DVD player has a wide dynamic range.Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakersmaybedamaged.
• For connection to yourTV, see“Connecting to aTV” .
• This section uses the following reference marks.
:Front speaker
:Rear speaker
:Subwoofer
:Center speaker
:Signalflow
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
Warning
• When you are connecting (via the COAXIAL DIGITAL
AUDIOOUTjack)anAV decoder that does not haveDolby
Digital,DigitalTheater Systems(DTS)orMPEG2decoding
function, be sure to set “Digital Output” to “PCM” from the
on-screen displays. Otherwise, high volume sound may
damage your hearing as well as the speakers.
• WhenplayingDTS-encodeddiscs(DVDsandaudioCDs),
excessivenoisemaybeoutput fromtheanalogaudiooutput
jacks. To avoid possible damage to the audio system, you
shouldtakeproper precautionswhentheanalog audiooutput
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an
external 5.1 channel DTS Digital Surround™ decoder
system must be connected to the COAXIAL DIGITAL
AUDIO OUT jack of the DVD player.

14
Connections
Dolby Surround Pro Logic
You canenjoythedynamicrealisticsoundofDolbySurroundProLogicbyconnecting
an amplifier and speaker system (right and left front speakers, a center speaker,
and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connectthe equipment the same wayas describedin“Connectingto an amplifier
equipped with a Dolby®Digital decoder.” Refer to that amplifier’s owner’s manual
and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear speakers will
be monaural even if you connect two rear
speakers.
• Makethefollowingsetting.
On-screendisplay Select: Page
“DigitalOutput” “PCM”or
“Raw”
32
Connecting to an amplifier equipped with Dolby Surround Pro Logic
To ANALOG
AUDIO OUT
To audio
input
To wall
outlet
Amplifier equipped with
Dolby Surround Pro Logic
Audiocable(not supplied)
Connecting to Optional Equipment (Continued)
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest
movies, and is now available to reproduce this realistic effect in the home.You can
enjoy motion picture and live concert DVDs with this dynamic realistic sound by
connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital
decoderor Dolby Digital processor.Ifyou haveaDolbySurroundProLogic decoder,
you will obtain the full benefit of Pro Logic from the same DVD movies that provide
full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby
Surround mark.
ManufacturedunderlicensefromDolby
Laboratories.Dolbyandthedouble-D
symbol are trademarks of Dolby
Laboratories.
• Use DVDs encoded via the Dolby
Digital recording system.
• Make the following setting.
On-screendisplay Select:
Page
“PCM”or
“Raw”
“DigitalOutput”
Connecting to an amplifier equipped with a Dolby®Digital decoder
To COAXIAL
DIGITAL
AUDIO OUT
To COAXIAL
type digital
audio input
Amplifier equipped with a
Dolby Digital decoder
To wall
outlet
75 ΩΩ
ΩΩ
Ωcoaxial cable (not supplied)
32

15
Connections
Connections
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left front
speakers).
75 ΩΩ
ΩΩ
Ωcoaxial cable (not supplied)
• Make the following setting.
On-screendisplay Select: Page
“PCM”
“DigitalOutput”
MPEG2 sound
You can enjoy motion picture and live concert DVDs with dynamic realistic sound
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2
audio processor.
• UseDVDs encodedviathe MPEG2
recording system.
• Make the following setting.
On-screendisplay Select:
Page
“PCM”or
“Raw”
“DigitalOutput”
Connecting to an amplifier equipped with an MPEG2 audio decoder
Connecting to an amplifier equipped with a digital audio input
To COAXIAL
DIGITAL
AUDIO OUT
To COAXIAL
type digital
audio input
Amplifier equipped with an
MEPG2 audio decoder
To wall
outlet
Amplifierequippedwith
a digital audio input
To wall
outlet
To COAXIAL
type digital
audio input
To COAXIAL
DIGITAL
AUDIO OUT
75 ΩΩ
ΩΩ
Ωcoaxial cable (not supplied)
32
32
DigitalTheater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for
home use, on DVDs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVDs or audio CDs.
• Use DVDs or audio CDs encoded
via the DTS recording system.
• Make the following setting.
On-screendisplay Select: Page
“DigitalOutput” “Raw”
To COAXIAL
DIGITAL
AUDIO OUT
To COAXIAL
type digital
audio input
Amplifier equipped with a
DTS decoder
To wall
outlet
75 ΩΩ
ΩΩ
Ωcoaxial cable (not supplied)
32
Connecting to an amplifier equipped with a DTS®decoder
Manufactured under license under U.S.
Patent #: 5,451,942 & other U.S. and
worldwidepatentsissued&pending.DTS
and DTS Digital Out are registered
trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. ©
1996-2007DTS,Inc.AllRights Reserved.

16
Basic playback
To turn the power off
Press ON/STANDBYtoturntheunit off.
Notes
• DonotmovetheDVDplayerduringplayback.Doing so maydamage
thedisc.
• Use the OPEN/CLOSE button to open and close the disc tray.
Do not push the disc tray while it is moving. Doing so may cause
theDVD playertomalfunction.
• Do not push up on the disc tray or put any objects other than
discs on the disc tray. Doing so may cause the DVD player to
malfunction.
• In many instances, a menu screen will appear after playback of
a movie is completed. Prolonged display of an on-screen menu
may damage your television set, permanently etching that image
onto its screen. To avoid this, be sure to press the STOP button
on your remote control once the movie is completed.
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Preparations
• When you want to view a disc, turn on the TV and select the
video input connected to the DVD player.
• When you want to enjoy the sound of discs from the audio
system, turn on the audio system and select the input
connected to the DVD player.
Notes
• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last stopped.
For resuming playback, see
17
.
• Some video CD are recorded with PBC (Playback Control), a
menu with recorded contents may appear on the TV if you
have turned the PBC on. You can make your selection
according to its PBC menu. Press the PBC button on the
remote control to turn PBC on or off anytime during Video CD
playback. When switching from PBC off to PBC on mode,
playback will start from the beginning of the disc.To turn on the
menudisplayagain,presstheRETURN button.
To pause playback (still mode)
Press PAUSE/STEPduring playback.
To resume normal playback, press the
PLAY button.
• The sound is muted during still mode.
To stop playback
PressSTOP.
To remove the disc
PressOPEN/CLOSE.
Remove the disc after the disc tray
openscompletely.
Be sure to press the OPEN/CLOSE button to close the
disc tray after you remove the disc.
Basic playback
To start playback in the stop mode
PressPLAY.
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during
a normal broadcast may appear on the TV screen while
playing a DVD because the high resolution pictures on these
discs include a lot of information.While the amount of noise
depends on the TV you use with this DVD player, you should
generally reduce the sharpness adjustment on yourTV when
viewingDVDs.
If you insert a DVD that contains a top menu, a
menu may appear. Use / / / to select the
title you want to view, then press ENTER to start
playback.
• You may need to press the TOP MENU or MENU
buttontodisplay disc menu (depending on the actual
DVD.)
Press ON/STANDBY.
The DVD player turns on.
Press OPEN/CLOSE.
Thedisc tray opens.
Place the disc on the disc tray.
Withtheplayback side
down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray.If the disc is out of
theguide,itmaydamagethediscandcausetheDVD
player to malfunction.
• Do not place a disc which is unplayable in this DVD
player.
PressOPEN/CLOSE to closethe disc tray.
Playbackstarts.
1
2
3
4
ON/STANDBY

17
Basic playback
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
REV: Fast reverse playback
FWD: Fast forward playback
Eachtimeyoupress the REV or FWD
button, the playback speed changes.
To resume normal playback
PressPLAY.
Notes
• The DVD player mutes sound and subtitles during reverse
and forward scan of DVDs.
• The playback speed may differ depending on the disc.
Playing in slow-motion
Press SLOW during playback.
Each time you press the SLOW
button, the slow-motion speed
changes in the following sequence:
To resume normal playback
PressPLAY.
Notes
• The sound is muted during slow-motion playback.
• 3 speeds are available.
Press PAUSE/STEP during still playback.
EachtimeyoupressthePAUSE/STEP
button, the picture advances one
frame.
To resume normal playback
PressPLAY.
Note: The sound is muted during frame by frame playback.
Playing frame by frame
Resumingplayback from the same location
Notes
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while
the DVD player keeps a location in the memory may function
only after the memory is cleared.
Press STOP at the location where you
want to interrupt playback.
The DVD player memorizes the
location where playback is stopped.
Press PLAY.
The DVD player resumes playback
from the location where you stopped
playback.
1
2
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location where you stopped playback.

18
Basic playback
Locating a specific chapter or track
Press SKIP or repeatedly to access
the chapter or track number you want.
Playbackstarts from the selected chapter or track.
To locate succeeding chapters or tracks.
Playback starts from the beginning of the
current chapter or track.
When you press twice in quick
successions, playback starts from the
beginningofthe preceding chapter or track.
Note
• Some titles may not display chapter numbers.
Normally, DVDs are divided into titles, and the titles are sub-divided into chapters.VIDEO CDs and audio CDs are divided into
tracks.You can quickly locate any specific title, chapter, or track.
Locating a title using the top menu
PressTOP MENU.
The top menu appears on the TV
screen.
e.g.
Press / / / to select the title you
want.
Ifthetitlesinthetopmenuareassigned
a number, you can directly locate a
specifictitleby pressing its designated
numberwiththenumberbuttons.
Press ENTER.
Playback starts from chapter 1 of the
selected title.
1
2
3
Notes
• The instructions above describe basic procedures which may
vary depending on the contents of the DVD. If different
instructions appear on theTVscreen,followthoseinstructions.
• Ifyoudisplaythe top menu during playbackandpresstheTOP
MENU button again without selecting any title, the DVD player
may resume playback from the point where you first pressed
theTOP MENU button (depending on the actual DVD.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that displays
the top menu as TITLE button.
Locating a Desired Section
To start playback from the beginning regardless of the location where you stopped playback.
1 Press STOP twice.
The DVD player deletes the memory of the location.
2 Press PLAY.
Playbackstarts from the beginningof the current title.
Playbackstarts from the beginningof the disc.
Playback starts from the beginning of the current track.
• If you want to return to the
beginning of a DVD, open
and close the disc tray once
with the OPEN/CLOSE
button before pressing the
PLAYbutton.

19
Advanced playback
Accessing a Specific Location Directly
Locating a specific title/chapter/time
PressT.
Press / to highlight theTitle/Chapter/
Track/Time.
Press / to select a section you want to
locate.
1
2
e.g.When you want to locate a chapter.
SEARCH
T
1
2
00:11:42
2
00:01:05
Track
Time
Disc Time
1
3
00:31:42
e.g.
Or
Press the number buttons to enter title,
chapter (track) number or time.
Press ENTER.
Playback starts from the selected
section.
3
Notes
• Pressing the CLEAR button resets the numbers. To clear
the display, press the T button several times.
• For VCD with PBC on, accessing tracks using number
buttons does not work.
To set andplay favoritebookmarkduring playback
1.Press T twice, the display of Bookmark appears, then
press ENTER to mark the desired scene.
2. Press ENTER to play the favorite bookmark.
To set other bookmarks.
Follow step 1 and move through the menu by pressing
the or button.
PressT again to remove this display.
To cancel the Bookmark
Followstep1, then press the CLEARbuttonto cancel the
bookmark.Movethroughthe menu by pressing the or
buttonto cancel other bookmarks.
Notes
• Some discs may not work with marking operation.
• The marking is canceled when you open the disc tray or turn
the power off.
• Some subtitles recorded around the marker may fail to
appear.
Bookmark
Accessing chapters/tracks using number
buttons:
For chapter/track numbers 10 to 19, press +10 once
and the number 10 appears then enter one digit.
Press ENTER.
For chapter/track numbers 20 to 29, press +10 twice
and the number 20 appears then enter one digit.
Press ENTER.
For example, if you want to select chapter/track 25,
first press +10 twice then press the number button
“5”.Then press ENTER.
Accessing the time using number buttons:
Just enter 2 digits in order.
The first two numbers you entered represent
seconds.
The second two numbers you entered represent
minutes.
The third two numbers you entered represent hours.
Advanced playback
SEARCH
T

20
Advanced playback
Repeating a Specific Segment
You can specify a desired segment and repeat it.
Repeatinga specific segment
To resume normal playback
Press A-B RPT until Rep AB Off is displayed.
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles.
• You can specify a segment only within the current title or
track (VIDEO CD).
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
Press A-B RPT again at the end of the
segment (point B).
The DVD player automatically returns to
point A and starts repeat playback of the
selectedsegment(A-B).
2
1
A-B RPT
Playing in a Varied Order
You can play titles, chapters within a title, or tracks in a varied order.
For Audio CD, please see“Playing MP3/WMA files”
26
.
Playing titles, chapters or tracks in a varied order
Press PLAY MODE.
Press / button to select desired
featuresandthenpressENTERbutton
to toggle desired mode.
1
e.g.
Shuffle: Playbacksinrandomorder.
PBC: Playbacks in PBC On mode (VCD only).
Repeat Chapter: Repeatsthecurrentchapter.
RepeatTitle:Repeatsthecurrenttitle.
Single: Repeats the current track.
All: Repeats the entire disc.
Off: Resumesnormalplayback.
Normal
Shuffle
Mode Normal
Repeat
Repeat Chapter
Repeat Title
Single
PBC
(
VCD onl
y)
Play Mode
:Off
PLAY MODE
Press PLAY.
Press the PLAY button, the DVD
player starts playback in the selected
mode.
To resume normal playback
Press ENTER until the Off/Normal is displayed.
Note
Some discs may not permit these operations.
2
Rep A-
Rep A-B
RepABOff
A-B RPT
A-B RPT