Toshiba HDR5010 User manual

Digital TV recorder
HDR5010KB
OWNER’S MANUAL
© 2010 Toshiba Corporation
HDR5010 User Guide.indb 1 22/07/2010 10:38

Introduction
2
Important Safety Information
Thank you for choosing this Toshiba Digital TV recorder.
Before using the Digital TV recorder, please take a minute to read the following important
safety information.
•Although this appliance has been
carefully manufactured and rigorously
checked prior to leaving the factory, as
with all electrical appliances it is possible
for problems to develop. If you notice
smoke, an excessive build-up of heat
or any other unexpected phenomena,
you should disconnect the plug from the
mains power socket immediately.
•Ensurethattheunitissufciently
ventilated! Never place next to or
underneath curtains!
•Only use the supplied AC mains adapter.
•This AC mains adapter should only be
connected to an AC 230V/50Hz mains
power supply - do not attempt to connect
it to any other type of supply.
•The socket-outlet must be installed near
the equipment and easily accessible.
•DO NOT cut off the supplied AC mains
adapter’s plug.
•Always hold the plug when pulling it out
from the power mains supply system.
DO NOTpullonex.Theexcan
become overloaded and cause a short
cut.
•Set up unit so that no one is able to trip
overtheex.
•This unit is recommended to be installed
on shock-free benches in order to avoid
any danger from falling.
•DO NOT use the unit near heat sources.
Thecasingandexcouldbedamaged
by the effect of heat.
•Any repairs must be carried out by
qualiedservicepersonnelonly.
•DO NOT open this unit. If you are in
doubt about it working normally, switch
off, unplug the AC mains adapter and
consult your dealer.
•Avoid placing the unit on any surfaces
that may be subject to vibrations or
shocks.
•Leave a space of at least 10cm around
the unit to allow for adequate ventilation.
•Place the unit on a stable surface.
•DO NOT place any magnetic objects
(including speakers) on or near the unit.
•DO NOT place any objects on the unit.
•DO NOT obstruct the ventilation on the
underside of the unit.
•DO NOT expose the unit to shocks or
vibrations as this could cause Hard disk
drive damage.
•To protect the unit during a thunder
storm unplug the AC power cord and
disconnect the aerial.
•CAUTION: DO NOT touch the aerial
connector.
•When you leave your home for a long
period of time, unplug the AC mains
adapter for safety reasons.
HDR5010 User Guide.indb 2 22/07/2010 10:38

Introduction
3
Important Safety Information
•The unit becomes warm under normal
operation. DO NOT place any covers or
blankets on the unit in order to prevent
overheating. The ventilation holes are not
to be blocked.
DO NOT set up near radiators.
DO NOT place in direct sunshine.
•DO NOT allow the unit to get wet.
•DO NOT use the unit in hot, humid or
excessively dusty places.
•DO NOT expose the unit to rain or
moisture.
•The apparatus shall not be exposed to
dripping or splashing and that no objects
lledwithliquids,suchasvases,shallbe
placed on the apparatus.
•Liquids spilled into the unit can cause
serious damage. Switch the set OFF and
disconnect the AC mains adapter, then
consultaqualiedservicepersonbefore
attempting to use the unit again.
•Moisture condensation occurs, for
example, when you pour a cold drink
into a glass on a warm day. Drops of
water form on the outside of the glass. In
the same way, moisture may condense
inside this unit.
DO NOT use the unit when moisture
condensation may occur.
If you use the unit in such a situation,
it may damage the Hard disk drive and
internal parts. Leave the unit for two or
three hours.
•To clean the unit, use a lightly dampened,
soft cloth. DO NOT use any kind of
abrasive cloth, sponge or cleaner.
•To help prevent Screen burn on Plasma
or LCD screens and CRT displays. Never
leave static pictures on the screen for
long periods of time.
•Neverplacehotobjectsofopename
sources, such as lighted candles or night
lights, on or close to the unit.
•High temperatures can melt plastic and
leadtores.
•DO NOT stand the unit vertically. Use the
unitinahorizontal(at)positiononly.
•The AC mains adapter is used as a
disconnecting device and therefore
should be readily operable.
•WARNING: To prevent the
spreadofre,keepcandles
orotheropenamesaway
from this product at all times.
HDR5010 User Guide.indb 3 22/07/2010 10:38

Introduction
4
General Information
Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction
of this unit, including, without limitation, any one of the following:
•Failure to record contents intended to be recorded by the consumer.
•Failure to edit contents as intended by the consumer.
Note:
• In the event your product is returned to our service centre, we are unable to guarantee your recordings will be
maintained.
Hard Disk Drive (HDD) Handling
The HDD is a precision apparatus that is susceptible to vibration, strong impact or dirt.
Depending on the installation environment or handling, the unit may become partially
damaged or in the worst case, recording or replaying may not be available. Especially while
the HDD is in motion, do not subject it to vibration or strong impact or pull out the power plug.
And if a power failure occurs, the content of the recording / replaying programme may be lost.
HDD rotates at high speed when in operation. Be sure that rotation has stopped and then
move the unit without subjecting it to strong impact or vibration.
We do not assume any liability for losses caused by misuse or malfunction.
About HDD
The HDD is a special device which has high recording density and is suited for long-time
recording or high-speed cueing but by contrast, has many factors which can cause breakage.
•When an HDD fails, recovery of recorded content (data) may be impossible.
•The HDD is not a permanent storage location of the recorded contents.
About the remaining capacity of HDD recording time:
In recording to the HDD, the Remaining Capacity Display may differ from the actual
recordable time as this unit adopts Variable Bit Rate encoding, which varies the recording
(storage) amount of data in conformity with the amount of information in the video signal.
BeforerecordingtotheHDD,ensurethereissufcientspaceontheHDDbydeleting
unnecessary titles in advance.
Notes on Copyright
About Copyright
Unauthorised copying, broadcasting, public performance and lending of discs are
prohibited. This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright protection
technology must be authorised by Rovi Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorised by Rovi Corporation. Reverse
engineering or disassembly is prohibited.
HDR5010 User Guide.indb 4 22/07/2010 10:38

Introduction
5
Notes on Copyright
Copyright protection system
ToplaybackhighdenitionvideoimagesviaanHDMIconnection,itisnecessarythat
boththeplayerandthedisplaydevice(oranAVamplier)supportacopyrightprotection
system called HDCP (high-bandwidth digital content protection system).
•HDCP is copy protection technology that comprises data encryption and authentication
of the connected AV device.
•This unit supports HDCP.
•Pleasereadtheoperatinginstructionsofyourdisplaydevice(orAVamplier)formore
information.
•Because HDMI is an evolving technology, it is possible that some devices with an HDMI
input may not operate properly with this unit.
•When using an HDCP-incompatible display device, the image will not be viewed properly.
•When power failure occurs or when you unplug the unit, HDMI settings may change.
Please check and set the HDMI settings again.
*HDMI:HighDenitionMultimediaInterface
Environmental Information
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household
waste. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. For more detailed information
aboutrecyclingofthisproduct,pleasecontactyourlocalcityofce,yourhousehold
waste disposal service or the shop where you purchased the product.
Disposal of batteries and/or accumulators
The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators
must be collected and disposed of separately from household waste.
Ifthebatteryoraccumulatorcontainsmorethanthespeciedvaluesoflead(Pb),
mercury(Hg),and/orcadmium(Cd)denedintheBatteryDirective(2006/66/EC),then
the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear
below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure the proper
disposal of products and batteries and thus help to prevent potential negative
consequences for the environment and human health.
For more detailed information about the collection and recycling programmes available
inyourcountry,pleasecontactyourlocalcityofceortheshopwhereyoupurchased
the product.
In conformity with the WEEE Regulations.
HDR5010 User Guide.indb 5 22/07/2010 10:38

Introduction
6
End User Licence
This product includes software code developed by third parties, including software code
subject to the GNU General Public License (‘GPL’) or GNU Lesser General Public License
(‘LGPL’). As applicable, the terms of the GPL and LGPL, and information on obtaining
access to the GPL Code and LGPL used in this product, are available to you - please
contact the manufacturer.
The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY
WARRANTY and is subject to the copyrights of one or more authors. For details, see the
GPL Code and LGPL Code for this product and the terms of the GPL and LGPL.
Trademark Acknowledgements
•Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol
are registered trademarks of Dolby Laboratories.
•DVB is a registered trademark of the DVB Project. This logo indicates that the product is
compliant with European Digital Broadcasting.
•HDMI,theHDMIlogoandHigh-DenitionMultimediaInterfacearetrademarksor
registered trademarks of HDMI Licensing LLC.
•The FREEVIEW+ HD words and logos are trademarks of DTV Services Ltd and are used
under licence. © DTV Services Ltd.
EU Conformity Statement
“This product is marked with “CE” and complies therefore with the applicable
harmonizedEuropeanstandardslistedundertheLowVoltageDirective2006/95/EC
and the EMC Directive 2004/108/EC.”
Responsible for CE-marking is TOSHIBA INFORMATION SYSTEMS (U.K.) LTD,
Toshiba Court, Weybridge Business Park, Addlestone Road, Weybridge,
Surrey, KT15 2UL, United Kingdom
HDR5010UserGuide.indb6 22/07/2010 10:38

Table of Contents
Introduction
Important Safety Information ................................................................................................2
General Information..............................................................................................................4
Notes on Copyright...............................................................................................................4
Environmental Information....................................................................................................5
End User Licence .................................................................................................................6
Trademark Acknowledgements ............................................................................................6
Getting Started
Package Contents ................................................................................................................8
Overview of the Digital TV Recorder ....................................................................................9
Overview of the Remote Control ........................................................................................10
Inserting the Batteries into the Remote Control..................................................................12
Connecting your Digital TV Recorder.................................................................................13
Switching your Digital TV Recorder On..............................................................................14
Automatic Tuning................................................................................................................15
Using your Digital TV Recorder
Everyday Use .....................................................................................................................16
Common Symbols ..............................................................................................................17
The Electronic Programme Guide (EPG) ...........................................................................18
The Channel List ................................................................................................................19
The Info Display..................................................................................................................20
Picture In Picture (PIP).......................................................................................................21
Recording Programmes......................................................................................................22
Timeshifting ........................................................................................................................25
The Timers Screen .............................................................................................................26
Modifying Timers ................................................................................................................27
The Library Screen.............................................................................................................29
The Photo Viewer...............................................................................................................31
The Main Menu...................................................................................................................33
Main Menu Structure ..........................................................................................................33
Main Menu Options ............................................................................................................34
Additional Information
Programming the Remote Control......................................................................................40
Manual Programming the Remote Control.........................................................................41
Finding the Remote Control’s Current Codes.....................................................................41
Troubleshooting..................................................................................................................42
Specications .....................................................................................................................44
Remote Control Brand Codes ............................................................................................46
Introduction
7
HDR5010 User Guide.indb 7 22/07/2010 10:38

Package Contents
HDR5010KB
QUICK START MANUAL
© 2010 Toshiba Corporation
q
Digital TV recorder
wRemote control eBatteries (2x R3/AAA)
rAC mains adapter* tOwner’s manual yQuick start guide
uHelpleaet
* For use exclusively with this Digital TV recorder. Never use this AC mains adapter with any other
device,asitmaycausereand/orproductdamage.
q
w
er
t
y
u
Getting Started
8
HDR5010 User Guide.indb 8 22/07/2010 10:38

Overview of the Digital TV Recorder
Front Panel
Rear Panel
qAerial input socket wAerial (loop through)
output socket
eLAN socket
rHDMI output socket tHDMI input sockets 1/2 yUSB socket
uSPDIF optical output
(Standard TOS link
connector)
iPower socket oSCART output socket
Standby / ON switch
and indication
Front panel display
q
USB socket
w e r t y i o
u
Getting Started
9
HDR5010UserGuide.indb9 22/07/2010 10:38

Overview of the Remote Control
3$
3!
2(
2*
3#
2&
3@
3)
2^
2$
2%
q
r
t
u
y
1)
1#
1%
o
1*
e
1&
i
w
1@
1$
1!
1^
2#
2@
1(
2)
2!
Getting Started
10
HDR5010 User Guide.indb 10 22/07/2010 10:38

q
TV - Switches the TV on/into Standby*.
w
DTT - Switches the viewing mode to DTT.
e
HDMI 1 - Switches the input mode to HDMI 1.
r
0-9 - Selects channels, enter PIN.
t
AD-SwitchesAudioDescriptiononoroff.Refertopage16formoreinformation.
y
SUB - Displays subtitles (if available).
u
+/− - Adjusts the TV’s volume*.
i
PIP - Enters Picture In Picture mode. Refer to page 21 for more information.
o
CLOCK - Displays the clock.
1)
GUIDE - Switches the Electronic Programme Guide (EPG) on/off. Refer to page 18 for more
information.
1!
BACK-Returnstothepreviouslevelinthemenu.ExitsEPG,Infoandmenu(rstlevel).
1@
LIB-DisplaystheLibraryofrecordedprogrammes.Refertopage29formoreinformation.
1#
MENU - Displays/exits the menu.
1$
- Pauses and resumes live TV. Refer to page 25 for more information about Timeshifting.
Plays and pauses recordings in the Library.
1%
- Stops playback when viewing recordings. Stops recording.
1^
- Skips back 30 seconds when viewing a recording or watching live TV. Press and hold to skip
to the start when viewing a recording or skip to the start of the pause buffer when watching live TV.
1&
- Rewinds live TV and recordings. Press repeatedly to increase the rewind speed.
1*
Coloured buttons - Selects options in digital text/EPG/Channel List/menu.
1(
- Fast forwards recordings. Press repeatedly to increase the fast forward speed. When
pausing live TV or recordings, press to watch in slow motion.
2)
- Skips forward 30 seconds when viewing a recording. Press and hold to skip to the end
when viewing a recording.
2!
- Records live TV. Sets highlighted programmes to timer record in the EPG.
2@
TV INPUT - Switches between the available TV input modes (eg DTT, HDMI or AV).*
2#
TIMER-DisplaystheTimersscreen.Refertopage26formoreinformation.
2$
TEXT - Displays digital text (if available).
2%
OK/ / / / -DisplaystheChannelList/conrmsaselection(OK button). Navigate the EPG/
menu/Channel List/Info menu ( / / / buttons).
2^
INFO - Displays programme and recording information. Refer to page 20 for more information.
2&
SAVER - Displays the screen saver.
2*
TV/RAD - Switches between Digital TV channels and Digital Radio channels.
2(
- Turns the TV’s sound on/off*.
3)
Ch.+/− - Selects the next/previous channel.
3!
- Returns to the previous channel watched. Switches between 4 and 24 hours advance in EPG.
3@
HDMI 2 - Switches the input mode to HDMI 2.
3#
USB - Switches the input mode to USB.
3$
STB - Switches the Digital TV recorder on/into Standby.
*TheremotecontrolmustrstbeprogrammedtooperateyourTV.Refertopage40.
Getting Started
11
HDR5010 User Guide.indb 11 22/07/2010 10:38

Inserting the Batteries into the Remote Control
1. Lift open the battery compartment cover (as shown).
2. Install 2 “R3/AAA” batteries (included); the correct polarity is shown inside the battery
compartment. Always check the positive/negative symbols on the batteries to ensure
they are inserted correctly.
3. Replace the battery compartment cover and push down until it clicks shut.
Note:
• Always dispose of old batteries safely. Check with your local council for how you should get rid of batteries.
Neverputbatteriesonareorinthebinwithnormalhouseholdwaste.
• A label with support information is located on the back of the remote control.
Getting Started
12
HDR5010 User Guide.indb 12 22/07/2010 10:38

Connecting your Digital TV Recorder
qPlug your aerial lead into the RF IN socket of the recorder.
wIf required, plug an Ethernet cable between the LAN socket and an Ethernet
system. Refer to page 37 for more details. Cable not supplied.
eIf required, plug a SCART cable between the SCART OUTPUT socket of the
recorder and your TV, Video or DVD recorder. Cable not supplied.
rIf required, plug a RF cable between the RF OUT socket of the recorder and your
TV, Video or DVD recorder. Cable not supplied.
tPlug a HDMI cable between the HDMI OUT socket of the recorder and your TV.
Cable not supplied.
y
If required, plug a HDMI cable between your DVD player, DVD recorder, Set-top box,
Games console and the HDMI IN 1 or 2 socket of the recorder. Cable not supplied.
uIf required, plug a USB Flash drive or a cable from a Digital Still Camera or Card
reader in to the USB socket. Refer to page 31 for more details.
iIf required, plug an Optical cable (TOS link) between the SPDIF output socket of
the recorder and your Hi-Fi or Surround Sound System. Cable not supplied.
oPlug the supplied AC mains adapter between the power socket of the recorder and
a standard wall socket. Only switch on the wall socket when all cables have
been attached. (Do not cut off the supplied AC mains adapter’s plug.)
Note:
• Refertopage16formoreinformationonhowtochangetheinputmodetoHDMI1or2andUSB.
• AHDMIcableisrecommendedasitgiveshigherqualitypictureandsoundandisrequiredforHighDenition
viewing.
• Socket names vary according to make and model of your equipment.
• The USB socket does not support all USB devices or cameras.
TV aerial
tiu ro
ew
y
q
Getting Started
13
HDR5010 User Guide.indb 13 22/07/2010 10:38

Switching your Digital TV Recorder On
To Turn On Power to the Unit:
1. Switch On power at the wall socket, if required.
2. Within a few seconds the front panel will display “Starting” and the Power ring LED will
light.
3. After start up is complete, an image is displayed on your TV screen and the Power ring
LED will change to Blue.
To Turn Off Power to the Unit:
1. Press the [ ] button on the remote control or the Standby button on the front of the unit .
The Power Ring changes to Red.
2. Press the switch on the wall socket and remove the AC mains adapter, to completely
turn Off the power to the unit.
Standby
When the Red Power LED is on the unit is in Standby. You can go In/Out of Standby by
pressing the []button on the remote control or
the Standby button on the front of the unit .
Note:
• It is recommended that the unit be left in Standby rather than switching Off completely, in order to allow
important updates to be received via your aerial.
• It is safe to put the Digital TV recorder into Standby mode when you have set programmes to record. The Digital
TV recorder will automatically wake up from Standby mode to make the recording.
• Whenever the unit receives a signal from the remote control, the Power LED blinks Red.
• After turning On, it takes some time before the unit starts up. Please note that buttons on the remote control
and the unit do not work during this period of time.
• Do not switch the power On/Off repeatedly within a short period of time. It could cause a malfunction.
• If a power cut occurs when using the unit, unplug the AC mains adapter to avoid sudden surges of electricity
when the power comes back on.
Front Panel Display
This will give you information about the DTT/Radio channel that is currently being watched
or listened to. It also displays symbols such when using the Digital TV
recorder functions. When using the Photo Viewer function “Photo” is displayed.
Getting Started
14
HDR5010 User Guide.indb 14 22/07/2010 10:38

Automatic Tuning
1. Ensure the aerial is plugged into this unit.
2. Oncetheunithaspoweredupforthersttime,thefollowingmenuisdisplayed.Press
the [OK] button to continue.
Note:
• On initial startup there is also an option available to access advanced setup by pressing the [RED] button
before tuning starts. Press the [BACK] button to return to the tuning screen.
3. The Digital TV recorder will now scan and store all available channels. Depending on the
quality of your reception, this may take several minutes. Please be patient and do not
press any buttons.
Note:
• Ifnochannelsarefound,amessageisdisplayedaskingyoutocheckyouraerial.Conrmthatyouraerialis
connected correctly and press the [OK] button to restart automatically tuning.
4. Onceautomatictuninghasnished,youmayseearegionpreferencescreensimilarto
the one shown below.
Select the region that is best for your area by pressing the [RED]
button, or to get further regions press the [OK] button (if available).
5. A summary screen, like the one below, is shown. Press the [OK] button to exit the
automatic tuning process.
Congratulations the Digital TV recorder is now ready to use.
Getting Started
15
HDR5010 User Guide.indb 15 22/07/2010 10:38

Everyday Use
Changing channels
Type in the channel number using the [0]-[9] buttons. Alternatively, press the [Ch+] and
[Ch-] buttons to select the next/previous channel.
Channel hopping
Press the []button to return to the previous channel watched. Hop between the current
and previous channel watched
Adjusting the volume*
Press the [+] and [-] buttons to increase/decrease the volume.
Muting the sound*
Press the []button to mute the sound. Press again to restore.
Displaying Digital Text
Press the [TEXT] button to display digital text (if available). Press again to exit digital text.
Displaying subtitles
Press the [SUB] button to display subtitles (if available). Press again to switch off the
subtitles.
Audio Description
Audio Description is a spoken explanation that describes all important information on a
programme, such as body language, facial expressions, scenery, action, costumes or
anything that helps to describe the plot of the story, event or image.
Press the [AD] button to switch on the Audio Description (If available from the broadcaster).
Press again to switch off the Audio Description.
Switching between TV and Radio channels
The Digital TV recorder stores all the Digital TV channels together and all the Digital Radio
channels together. Press the [TV/RAD] button to switch between Digital TV and Digital
Radio channels.
When you are listening to a radio channel, the screen saver will automatically start if you do
not press any button for a few minutes. Alternatively, press the [SAVER] button to display the
screen saver right away. To remove the screen saver, press any button on the remote control.
Switching between DTT, HDMI 1-2 or USB
While watching Digital TV programmes you can use the [DTT], [HDMI 1], [HDMI 2] or
[USB] buttons to select the input mode.
Note:
• When listening to TV programmes with Audio Description enabled, Dolby Digital sound is not available.
• HDMI pass through is only available when the unit is powered out of Standby and using HDMI output from this
unit.
*TheremotecontrolmustrstbeprogrammedtooperateyourTV.Refertopage40.
Using your Digital TV recorder
16
HDR5010UserGuide.indb16 22/07/2010 10:38

Everyday Use
Using Standby
When you’re not watching TV, you should set the Digital TV recorder to Standby. Press the
[ ] button to switch between On (Blue Power ring LED on the front panel) and Standby
(Red power LED on the front panel). This unit has a low power feature which means that
when left in Standby for a long period, it may take longer to power up.
It is safe to put the Digital TV recorder into Standby when you have set programmes to
record. The Digital TV recorder will automatically wake up from Standby to make the
recording. If you plan to leave the Digital TV recorder unattended for a long period and have
not set any programmes to record, put the Digital TV recorder into Standby and wait for 20
seconds before switching it off at the mains socket. If the mains socket doesn’t have a switch
unplug the AC mains adapter.
Automatic Standby
To help reduce the amount of electricity it uses, the Digital TV recorder will automatically
switch into Standby after 3 hours of inactivity. If you are still watching TV at this time, a
screen will be displayed allowing you to stop the Digital TV recorder entering Standby.
If no button is pressed while this screen is displayed, the Digital TV recorder will enter
Standby after a few seconds. It is possible to deactivate automatic Standby by setting the
Auto Standby option in the General Settings menu to Off. Refer to page 35.
Common Symbols
The following may be visible in the Electronic Programme Guide, Channel List, Info
display, Timers screen and Library menus.
Locked channel. Multiple audio languages available.
Encrypted/scrambled channel. Teletext available.
Radio Channel. Timer has been set.
Channel selected for moving. [S]Subtitles available.
Recording has been viewed. Selected channel is hidden.
Timer is set to “Series Record”. Playback of recording has been locked.
Recording has been protected from
deletion.
Play.
Pause. Record.
Slow motion. Fast Forward.
Rewind. FastForward(x16).
FastRewind(x16). Fast Forward (x128).
Fast Rewind (x128).
HD
HighDenition.
[AD]
Audio Description available.
Using your Digital TV recorder
17
HDR5010 User Guide.indb 17 22/07/2010 10:38

The Electronic Programme Guide (EPG)
The EPG displays programme information for the next 8 days (when transmitted by
broadcasters). You can also set programmes to be recorded from the EPG.
To Press
Access the EPG... [GUIDE] button.
Move around the EPG... [/ / / ] buttons or [0]-[9] buttons to
directly enter the channel number.
Display the previous nine channels in the
list...
[RED] button.
Display the next nine channels in the list... [GREEN] button.
Move forward 4 or 24 hours... [BLUE] button.
(Press to switch between 4 and 24 hours)
Move back 4 or 24 hours... [YELLOW] button.
(Press to switch between 4 and 24 hours)
View information for the highlighted
programme...
[INFO] button. Press again to return to the
EPG.
Set a highlighted programme to record... []button. Refer to page 23 for Recording
options.
Preview a current programme
(in the background)...
[OK] button.
Exit the EPG and switch to a previewed
programme...
[OK] button.
Exit the EPG... [GUIDE] or [BACK] button.
Note:
• If you accidentally set a wrong programme to record, press the []button again to cancel.
Current
channel
Date of
currently
displayed
programmes
List of
channels
Today’s
date and
current time
Time of
currently
displayed
programmes
Programme
information
Using your Digital TV recorder
18
HDR5010 User Guide.indb 18 22/07/2010 10:38

The Channel List
The Channel List displays all the available channels.
To Press
Access the Channel List... [OK] button while watching TV.
Select channels... [/ ] buttons.
Display the previous nine channels in the
list...
[RED] button.
Display the next nine channels in the list... [GREEN] button.
Switch to the selected channel... [OK] button.
Exit the Channel List... [BACK] button.
List of
channels
Highlighted
channel
Using your Digital TV recorder
19
HDR5010UserGuide.indb19 22/07/2010 10:38

The Info Display
When watching TV, the Info display gives brief information on the current and future
programmes (when the programme information is transmitted by broadcasters). You can
also set programmes to be recorded from the Info display. When watching a recording, the
Info display gives a brief description of the recorded programme.
To Press
Access Info for the current programme/
recording...
[INFO] button.
View information for future programmes on
the current channel...
[RIGHT] button.
View information for programmes on other
channels...
[/ ] buttons.
Change the Audio setting (if available)... [RED] button.
Change the Subtitle setting (if available)... [GREEN] button.
Change Audio Description language
(if available)...
[YELLOW] button.
Switch to another channel (when viewing
that channel’s information)...
[OK] button.
Set a current or future programme to
record...
[ ] button (whilst viewing that programme’s
information). Refer to page 22 for more
information.
Exit Info... [INFO] or [BACK] button.
Selected
programme’s
details
Today’s
date and
current
time
Selected programme’s
start and end time
Programme
name
Channel
Using your Digital TV recorder
20
HDR5010 User Guide.indb 20 22/07/2010 10:38