Toshiba 46XV640U - 46" LCD TV User manual

HIGH-DEFINITION TELEVISION
46XV640U
40XV640U
Owner’s Manual
Integrated High Definition
LCD Television
Foran overview of steps for setting up your new TV, see page 9.
Note: To display a High Definition picture, the TV must be receiving
a High Definition signal (such as an over-the-air High Definition
TV broadcast, aHigh Definition digital cable program, or a High
Definition digital satellite program). For details, please contact
your TV antenna installer, cable provider, orsatellite provider.
© 2008 TOSHIBA CORPORATION
All Rights Reserved
Owner’s Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshibadealer about this TV.
Model number:
Serial number:
HDA51T4000I

2
Dear Customer,
Thank you for purchasing this Toshiba LCD TV. This manual will
help you use the many exciting features of your new LCD TV. Before
operating your LCD TV, please read this manual completely, and
keep it nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING
RISK OF ELECTRIC SHOCK DO NOT
OPEN.
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
To prevent injury, this apparatus must be securely attached to the
floor/wall in accordance with the installation instructions. See item 23
on page 3.
WARNING: If you decide to wall mount this television, always
use a UL Listed wall bracket appropriate for the size and weight of
this television. The use of any wall bracket other than a UL Listed
wall bracket appropriate for the size and weight of this television for
wall mounting this television could result in serious bodily injury
and/or property damage. See “Removing the Pedestal Stand” (
page 5).
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s attention to
Article 820-40 of the U.S. NEC, which provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical. For additional antenna grounding
information, see items 30 and 31 on page 4.
Congratulations on your purchase! As you enjoy your
new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend
and larger flat panel displays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer’s recommendations.
• Flat panel displays that are
inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
• One size does NOT fit all. Follow the manufacturer’s recommendations
for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for
proper use of this product.
• Don’t allow children to climb on or play with furniture and
television sets.
• Don’t place flat panel displays on
furniture that can easily be used as
steps, such as a chest of drawers.
• Remember that children can
become excited while watching a
program, especially on a “larger
than life” flat panel display. Care
should be taken to place or install
the display where it cannot be
pushed, pulled over, or knocked down.
• Care should be taken to route all cords and
cables connected to the flat panel display so that they cannot be
pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your
flat panel display, always:
• Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction. If you
are unsure, contact a professional
installer.
• A minimum of two people are
required for installation. Flat panel
displays can be heavy.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat
Panel Display

3
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding type plug. A
polarized plug has two blades with one wider
than the other. A grounding type plug has
two blades and a third grounding prong. The
wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Precautions
14a) CAUTION: If the TV is dropped and the cabinet or enclosure
surface has been damaged or the TV does not operate normally,
take the following precautions:
ALWAYS turn off the TV and unplug the power cord to avoid
possible electric shock or fire.
NEVER allow your body to come in contact with any broken
glass or liquid from the damaged television. The LCD panel
inside the TV contains glass and a toxic liquid. If the liquid
comes in contact with your mouth or eyes, or your skin is
cut by broken glass, rinse the affected area thoroughly with
water and consult your doctor.
ALWAYS contact a service technician to inspect the TV any
time it has been damaged or dropped.
15) CAUTION:
To reduce the risk of electric shock, do not use the polarized
plug with an extension cord, receptacle, or other outlet
•
•
•
•
unless the blades can be inserted completely to prevent
blade exposure.
To prevent electric shock, match wide blade of plug to wide
slot; fully insert.
16) WARNING:
To prevent the spread of fire, keep candles or other open flames
away from this product at all times.
17) WARNING:
NEVER expose batteries to excessive heat such as sunshine,
fire, or the like.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and heed all warnings
when installing your TV:
18) ALWAYS plug the product into an outlet that is located in such
a manner that it can be easily unplugged in case the product
requires service.
19) NEVER route the product’s power cord inside a wall or similar
enclosed area.
20) Never modify this equipment. Changes or modifications may
void: a) the warranty, and b) the user’s authority to operate
this equipment under the rules of the Federal Communications
Commission.
21) DANGER: RISK OF SERIOUS
PERSONAL INJURY, DEATH, OR
EQUIPMENT DAMAGE!
Never place the TV on an unstable
cart, stand, or table. The TV may fall,
causing serious personal injury, death, or
serious damage to the TV.
22) To avoid damage to this product, never place or store the TV in
direct sunlight; hot, humid areas; or areas subject to excessive
dust or vibration.
23) Always place the TV on the floor or a sturdy, level, stable surface
that can support the weight of the unit. To secure the TV, use
a sturdy strap from the hook(s) on the rear of the TV to a wall
stud, pillar, or other immovable structure. Make sure the strap is
tight, secure, and parallel to the floor.
p
otVTedisVT
4"
min. Hook
Sturdy strap (as short as possible)
24) The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on the apparatus.
25) Never block or cover the slots or openings in the TV cabinet
back, bottom, and sides. Never place the TV:
on a bed, sofa, rug, or similar
surface;
too close to drapes, curtains, or
walls; or
in a confined space such as a
bookcase, built-in cabinet, or any
other place with poor ventilation.
(continued)
•
•
•
•
Wide blade

4
The slots and openings are provided to protect the TV from
overheating and to help maintain reliable operation of the TV. Leave
a space of at least 4 (four) inches around the TV.
26) Always place the back of the television at least four (4) inches
away from any vertical surface (such as a wall) to allow proper
ventilation.
27) Never allow anything to rest on or roll over the power cord, and
never place the TV where the power cord is subject to wear or
abuse.
28) Never overload wall outlets and extension cords.
29) Always operate this equipment from a 120 VAC, 60 Hz power
source only.
30) Always make sure the antenna system is properly grounded to
provide adequate protection against voltage surges and built-up
static charges (see Section 810 of the National Electric Code).
Antenna lead-in wire
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Power service grounding electrode
system (NEC Art 250 Part-H)
Ground clamp
Electric service equipment
Ground clamps
31) DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
Use extreme care to make sure you are never in a position
where your body (or any item you are in contact with, such
as a ladder or screwdriver) can accidentally touch overhead
power lines. Never locate the antenna near overhead power
lines or other electrical circuits.
Never attempt to install any of the following during lightning
activity: a) an antenna system; or b) cables, wires, or any
home theater component connected to an antenna or phone
system.
Care
For better performance and safer operation of your TOSHIBA TV,
follow these recommendations and precautions:
32) If you use the TV in a room whose temperature is 32 °F (0 °C)
or below, the picture brightness may vary until the LCD warms
up. This is not a sign of malfunction.
33) Always unplug the TV before
cleaning. Gently wipe the display
panel surface (the TV screen) using
a dry, soft cloth only (cotton, flannel,
etc.). A hard cloth may damage
the surface of the panel. Avoid contact with alcohol, thinner,
benzene, acidic or alkaline solvent cleaners, abrasive cleaners,
or chemical cloths, which may damage the surface. Never spray
volatile compounds such as insecticide on the cabinet. Such
products may damage or discolor the cabinet.
•
•
34) WARNING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into the TV
cabinet slots.
35) While it is thundering, do not touch the connecting cables or
apparatus.
36) For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or unused
for long periods of time.
37) ALWAYS unplug the TV to completely disconnect from mains
power. When the TV is turned off using the on/off switch, it is
not completely disconnected from power and a minute amount
of current is still consumed.
38) DANGER: RISK OF SERIOUS
PERSONAL INJURY OR
DEATH!
Never strike the screen with a sharp or
heavy object.
39) • The LCD screen of this product can be damaged by
ultraviolet radiation from the sun. When selecting a location
for the television, avoid locations where the screen may be
exposed to direct sunlight, such as in front of a window.
Never touch, press, or place anything on the LCD screen.
These actions will damage the LCD screen. If you need to
clean the LCD screen, follow the instructions in item 33 on
this page.
Service
40) WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening and removing
the covers may expose you to dangerous voltage or other
hazards. Failure to follow this WARNING may result in death or
serious injury. Refer all servicing not specified in this manual to
a Toshiba Authorized Service Center.
41) If you have the TV serviced:
Ask the service technician to use only replacement parts
specified by the manufacturer.
Upon completion of service, ask the service technician to
perform routine safety checks to determine that the TV is in
safe operating condition.
42) The cold cathode fluorescent lamp in the LCD panel contains a
small amount of mercury.
When the TV reaches the end of its useful life, dispose of
the used TV by the approved method for your area, or ask a
qualified service technician to properly dispose of the TV.
Note: The lamp(s) inside this product contain mercury.
Disposal may be regulated due to environmental
considerations. For disposal or recycling
information, contact your local authorities or the
Electronics Industries Alliance (www.eiae.org).
•
•
•

5
Choosing a location for your LCD TV
To Display your LCD TV on the included Pedestal
Stand:
Observe the following safety precautions:
1) Read and Follow the pedestal assembly instructions included
with the pedestal.
CAUTION: Before beginning pedestal assembly, carefully lay the
front of the LCD Panel face down on a flat, cushioned surface
such as a quilt or blanket. Leave the bottom of the unit protruding
over the edge of the surface and assemble the pedestal as
indicated below.
Note: Extreme care should always be used when attaching
the pedestal stand to avoid damage to the LCD panel.
2) Place the TV on a sturdy, level surface that can support the
weight of the TV.
3) Be sure to secure the TV to a wall, pillar, surface, or other
immovable structure. (item 23, page 3).
To Display your LCD TV using a Wall Bracket:
If you decide to wall mount your LCD TV, always use a UL listed wall
bracket appropriate for the size and weight of the LCD TV (page 2):
1) CAUTION: Two people are required for installation.
2) Unplug and remove any cables and/or other component
connectors from the rear of the TV.
3) Remove the screws of the VESA Mounting Pattern show in
the right diagram.
4) Follow the instructions provided with your wall bracket.
Before proceeding, make sure the appropriate bracket(s) are
attached to the wall and the back of the TV as described in the
instructions provided with the wall bracket.
5) After attaching the appropriate bracket(s) to the wall and the
back of the TV, remove the pedestal stand from the TV as
described below.
6) VESA Mounting Pattern
TV Size Hole Pattern(HxV) Screw Size
40” 200x200 mm M6
46” 400x200 mm M8
(unit in mm)
Removing the Pedestal Stand
1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface.
Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.
2) Remove the four screws shown in the right diagram. This will
allow removal of the pedestal stand.
3) Once you have removed all four screws holding the pedestal
stand in place, remove the pedestal stand from the TV.
CAUTION: Always place the TV on the floor or a sturdy, level, stable
surface that can support the weight of the unit. To secure the TV, use
a sturdy strap from the hook(s) on the rear of the TV to a wall stud,
pillar, or other immovable structure. Make sure the strap is tight,
secure, and parallel to the floor.
Four screws
Four screws
40” TV
46” TV
VESA Mounting Pattern
VESA Mounting Pattern
Hook
Sturdy strap
(as short as possible)
Hook
Sturdy strap
(as short as possible)

6
FCC Declaration of Conformity
Compliance Statement
(Part 15):
The Toshiba 40XV640U, and 46XV640U Televisions comply with
Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Consumer Products, L.L.C.
82 Totowa Rd. Wayne, NJ 07470.
Ph: 1-800-631-3811
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
removing and applying power to the equipment, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Caution: Changes or modifications to this equipment not
expressly approved by Toshiba could void the user’s authority
to operate this equipment.
•
•
•
•
ENERGY STAR®User Information
ENERGY STAR User Information Statement: the factory default
settings of this television meet ENERGY STAR requirements.
Changing Picture Settings may increase energy consumption,
possibly beyond the limits required for ENERGY STAR
qualification.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation. To
return to [Home] mode settings, select [Standard] picture mode.
[Standard] mode is recommended for normal home use.
ENERGY STAR®qualified TV. Products that
earn the ENERGY STAR prevent green house
gas emissions by meeting strict guidelines set
by the U.S. Environmental Protection Agency.
ENERGY STAR and the ENERGY STAR mark
are registered U.S. marks.
Important notes about your LCD
TV
The following symptoms are technical limitations of LCD
Display technology and are not an indication of malfunction;
therefore, Toshiba is not responsible for perceived issues
resulting from these symptoms.
An afterimage (ghost) may appear on the screen if a fixed,
nonmoving image is displayed for a long period of time. The
afterimage is not permanent and will disappear in a short
period of time.
The LCD panel contained in this TV is manufactured using
an extremely high level of precision technology; however,
there may be an occasional pixel (dot of light) that does not
operate properly (does not light, remains constantly lit, etc.).
This is a structural property of LCD technology, is not a
sign of malfunction, and is not covered under your warranty.
Such pixels are not visible when the picture is viewed from a
normal viewing distance.
Note: Interactive video games that involve shooting a “gun”
type of joystick at an on-screen target may not work with this
TV.
Trademark Information
QSound and [ ] symbol are trademarks of QSound Labs, Inc.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
1)
2)
•
•
•

7
Contents
Important Safety Instructions .......................................... 3
Installation, Care, and Service ........................................ 3
Chapter 1: Introduction.................................................. 8
Features of your new TV .........................................................8
Overview of steps for installing, setting up, and using
your new TV .....................................................................9
TV front and side panel controls and connections ................10
TV back panel connections....................................................11
Chapter 2: Connectin0.5g your TV ...................................12
Overview of cable types ........................................................12
About the connection illustrations.........................................12
Connecting a VCR ( or a VCR with S-video) and
antenna, Cable TV or Camcorder ...................................13
Connecting a DVD player with ColorStream®(component
video), a VCR, and a satellite receiver............................ 14
Connecting an HDMI™ or DVI device to the HDMI input..15
REGZA-LINK®connection................................................... 16
Connecting a digital audio system.........................................17
Connecting an audio system..................................................17
Connecting a personal computer (PC)................................... 18
Chapter 3: Using the remote control ................................. 19
Preparing the remote control for use .....................................19
Installing the remote control batteries ...................................19
Remote control effective range..............................................19
Learning about the remote control.........................................20
Using the remote control to control your other devices ........21
Remote Control functional key chart.....................................22
Programming the remote control to control your
other devices ...................................................................23
Remote control codes ............................................................24
Chapter 4: Menu layout and navigation .............................26
Main menu layout..................................................................26
Setup/Installation menu layout .............................................. 27
Navigating the menu system..................................................27
Chapter 5: Setting up your TV......................................... 28
Setting the Energy Saving Mode ...........................................28
Selecting the menu language .................................................28
TOSHIBA Logo LED............................................................ 28
Configuring the antenna input source for the
ANT/CABLE terminal....................................................28
Programming channels into the TV’s channel memory ........ 29
Programming channels automatically.............................29
Manually adding and deleting channels in the channel
memory.....................................................................29
Labeling channels..................................................................30
Setting the HDMI™ audio mode........................................... 31
Viewing the digital signal meter............................................ 32
Setting the time zone .............................................................32
Viewing the system status...................................................... 32
Chapter 6: Using the TV’s features ................................... 33
Selecting the video input source to view...............................33
Labeling the video input sources...........................................33
Tuning channels..................................................................... 34
Tuning channels using the Channel Browser™..............34
Setting the Channel Tuning Mode .................................. 36
Tuning to the next programmed channel ........................36
Tuning to a specific channel (programmed or
unprogrammed) ........................................................36
Switching between two channels using
Channel Return......................................................... 37
Switching between two channels using SurfLock™ ......37
Selecting the picture size .......................................................37
Scrolling the TheaterWide®picture
(TheaterWide 2 and 3 only) ............................................ 39
Using the auto aspect ratio feature ........................................39
Using the FREEZE feature....................................................39
Adjusting the picture .............................................................40
Selecting the picture mode.............................................. 40
Adjusting the picture quality........................................... 40
Using the closed caption mode..............................................41
Base closed captions ....................................................... 41
Digital CC Settings ........................................................41
CC Selector ..................................................................... 41
Adjusting the audio................................................................ 42
Muting the sound ............................................................42
Using the digital audio selector.......................................42
Selecting stereo/SAP broadcasts..................................... 42
Adjusting the audio quality.............................................43
Selecting the optical audio output format ....................... 43
Using the Dolby®Digital Dynamic Range Control
feature.......................................................................43
Using the Locks menu ...........................................................44
Entering the PIN code.....................................................44
If you cannot remember your PIN code.......................... 44
Changing your PIN code................................................. 44
Blocking TV programs and movies by rating
(V-Chip)....................................................................44
Downloading an additional rating system for
blocking TV programs and movies .......................... 45
Blocking channels...........................................................46
Unlocking programs temporarily....................................46
Using the input lock feature............................................46
Using the GameTimer®...................................................47
Using the control panel lock feature ...............................47
Using the PC settings feature.................................................47
Setting the PC Audio .............................................................48
Setting the sleep timer ...........................................................48
Using REGZA-LINK®...........................................................48
REGZA-LINK®playback device
(DVD player, etc.) control .......................................48
REGZA-LINK®input source selection........................... 49
VOLUME and MUTE controls of Audio Receiver ........49
Other REGZA-LINK®functions.....................................49
Displaying TV status information .........................................50
Understanding the auto power off feature ............................. 50
Understanding the last mode memory feature.......................50
Chapter 7: Using the TV’s advanced features ......................51
Using the advanced picture settings features......................... 51
Using dynamic contrast...................................................51
Using the static gamma feature....................................... 51
Selecting the color temperature ......................................51
Selecting the cinema mode ............................................52
Using the ClearFrame™ feature ..................................... 52
Using the Film Stabilization feature ............................... 52
Using CableClear®digital noise reduction .....................52
Using MPEG noise reduction .........................................53
Using the Game Mode feature ........................................53
Using the advanced audio settings features...........................53
Using the QSound®sound feature..................................53
Chapter 8: Troubleshooting............................................ 54
General troubleshooting ........................................................ 54
Chapter 9: Appendix.................................................... 56
Specifications.........................................................................56
Acceptable signal formats for PC IN and HDMI terminals ..57
Limited United States Warranty for LCD Televisions 26”
and Larger .......................................................................58
Limited Canadian Warranty for Toshiba Brand Flat Panel
Televisions ...................................................... 59

8
Features of your new TV
The following are just a few of the many exciting features of
your new Toshiba widescreen, integrated HD, LCD TV:
Integrated digital tuning (8VSB ATSC and QAM)
eliminates the need for a separate digital converter set-top
box (in most cases).
1080p output resolution.
Three HDMI™ digital, high-definition multimedia
interfaces 1080p input support ( page 15).
HDMI new capability
Lip-Sync Latency activates an audio/video display timing
adjustment function that allows HDMI source devices to
accurately perform synchronization automatically.
Two sets of ColorStream®HD high-resolution component
video inputs ( page 14).
QSound®audio technologies ( page 52).
Digital Audio Out optical audio connection with Dolby®
Digital optical output format ( page 43).
CableClear®digital picture noise reduction ( page 51).
PC IN (Analog RGB) computer terminal ( page 18).
Channel Labeling allows you to put the Call Letters (e.g.
ABC, HBO, etc.) on the screen along with the station
numbers, so you always know what you’re watching
( page 30).
REGZA-LINK allows control of external devices from the
TV remote via HDMI connection ( page 48).
•
•
•
•
•
•
•
•
•
•
•
Chapter 1: Introduction

Chapter 1: Introduction
9
Overview of steps for installing,
setting up, and using your new TV
Follow these steps to set up your TV and begin using its many
exciting features.
Carefully read the important safety, installation, care,
and service information. Keep this manual for future
reference.
Observe the following when choosing a location for the
TV:
Read “Important notes about your LCD TV”
( page 6).
Place the TV on the floor or a sturdy, level, stable
surface that can support the weight of the unit. Secure
the TV to a wall, pillar, or other immovable structure
(page 3).
Place the TV in a location where light does not reflect
on the screen.
Place the TV far enough from walls and other objects
to allow proper ventilation. Inadequate ventilation may
cause overheating, which will damage the TV. THIS
TYPE OF DAMAGE IS NOT COVERED UNDER
THE TOSHIBA WARRANTY.
Do not plug in any power cords until AFTER you have
connected all cables and devices to your TV.
BEFORE connecting cables or devices to the TV, learn
the functions of the TV’s connections and controls
( pages 10–11).
Connect your other electronic device(s) to the TV
( pages 12–18).
Install the batteries in the remote control ( page 19).
See “Learning about the remote control” ( page 20) for
an overview of the buttons on the remote control.
Program the remote control to operate your other
device(s) ( pages 21–25).
AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices. Then press
POWER on the TV control panel or remote control to turn
on the TV. If the TV stops responding to the controls on
the remote control or TV control panel and you cannot
turn the TV off or on, please unplug the power cords few
seconds then re-plug to try again.
See “Menu layout and navigation” for a quick overview
of navigating the TV’s menu system ( page 26).
Program channels into the TV’s channel memory
( page 29).
1
2
•
•
•
•
3
4
5
6
7
8
9
10
11
For details on using the TV’s features, see Chapters 6
and 7.
For help, refer to the Troubleshooting Guide, Chapter 8.
For technical specifications and warranty information,
see Chapter 9.
Enjoy your new TV!
12
13
14
15

Chapter 1: Introduction
10
TV front and side panel controls and connections
Model 40XV640U is used in this manual for illustration purposes.
Green LED and TOSHIBA Logo LED
Power LED(Green) = Power indicator
TOSHIBA Logo LED= On or Off (page 28).
Remote sensor — Point the remote control toward this
remote sensor (“Remote control effective range” on
page 19).
VIDEO-2 IN — The side panel A/V connections are
referred to as “VIDEO 2” and include standard A/V
connections.
Service port — For service use only. Used for updating
the television’s firmware.
POWER — Press to turn the TV on and off.
If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
1
2
3
4
5
ARROWS STWX — When a menu is on-screen, these
buttons function as up/down/left/right menu navigation
buttons.
MENU (ENTER) — Press to access the menu system (
pages 26–27). When a menu is on-screen, the MENU
button on the TV’s control panel functions as the ENTER
button.
EXIT — Press to instantly close an on-screen menu.
CHANNEL ST — When no menu is on-screen, these
buttons change the channel (programmed channels only;
 page 29).
VOLUME WX — These buttons adjust the volume level.
INPUT — Repeatedly press to change the source you are
viewing (ANT/CABLE, VIDEO 1, VIDEO 2, ColorStream
HD1, ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, PC).
6
7
8
9
10
11
TV front TV topLeft side panel
Control panel

Chapter 1: Introduction
11
TV back panel connections
For an explanation of cable types and connections, see pages 12–18.
HDMI™ IN — High-Definition Multimedia Interface input
receives digital audio and uncompressed digital video
from an HDMI device or uncompressed digital video
from a DVI device. Also see item 3. HDMI connection is
necessary to receive 1080p signals.
ColorStream®HD-1 and ColorStream®HD-2 — Two sets
of ColorStream®high-definition component video inputs
(with standard stereo audio inputs) for connecting devices
with component video output, such as a Toshiba DVD
player with ColorStream®.
Note: Component video cables carry only video
information; separate audio cables are required for a
complete connection.
VIDEO-1 IN — Standard (composite) video and standard
audio inputs plus optional S-video inputs for connecting
devices with composite video or S-video output.
Note: Standard (composite) video and S-video cables
carry only video information; separate audio cables are
required for a complete connection.
Audio OUT Variable — Analog audio outputs for
connecting an audio amplifier.
1
2
3
4
ANT/CABLE — Antenna input that supports analog
(NTSC) and digital (ATSC) off-air antenna signals and
analog and digital Cable TV (QAM) signals.
Digital Audio OUT — Optical audio output in Dolby
Digital or PCM (pulse-code modulation) format for
connecting an external Dolby Digital decoder, amplifier,
A/V receiver, or home theater system with optical audio
input.
PC/HDMI-1 (AUDIO) IN — PC audio input terminals are
shared with HDMI-1 analog audio input terminals, and
their use can be configured in the Audio Setup menu (
page 48).
PC IN — For use when connecting a personal computer.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
5
6
7
8
TV back
Power cord

12
Overview of cable types
Cables can be purchased from most stores that sell audio/
video devices. Before purchasing any cables, be sure of
connector types required by your devices and the length of
each cable.
Coaxial (F-type) cable
Coaxial (F-type) cable is used for connecting your antenna,
cable TV service, and/or cable converter box to the ANT/
CABLE input on your TV.
Standard A/V cables (red/white/yellow)
Standard A/V cables (composite video) usually come in sets
of three, and are for use with video devices with analog audio
and composite video output. These cables (and the related
inputs on your TV) are typically color-coded according to
use: yellow for video, red for stereo right audio, and white for
stereo left (or mono) audio.
S-video cable
S-video cable is for use with video devices with S-video
output. Separate audio cables are required for a complete
connection.
Note: An S-video cable provides better picture performance
than a composite video cable. If you connect an S-video
cable, be sure to disconnect the standard (composite) video
cable or the picture performance will be unacceptable.
Component video cables (red/green/blue)
Component video cables come in sets of three and are for
use with video devices with component video output.
(ColorStream®is Toshiba’s brand of component video.) These
cables are typically color-coded red, green, and blue. Separate
audio cables are required for a complete connection.
Note: Component video cables provide better picture
performance than a standard (composite) video or S-video
cable.
HDMI™ cable (with HDMI Logo “ ”)
HDMI (High-Definition Multimedia Interface) cable is for
use with devices with an HDMI output. An HDMI cable
delivers digital audio and video in its native format. This
cable carries both video and audio information; therefore,
separate audio cables are not required for a complete HDMI
device connection ( page 15 and page 18).
Note: HDMI cable provides better picture performance than
a standard (composite) video or S-video cable.
Optical audio cable
Optical audio cable is for connecting receivers with Dolby
Digital or PCM (pulse-code modulation) optical audio input
to the TV’s DIGITAL AUDIO OUT terminal ( page 17).
Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable is for connecting a PC
to the TV’s PC IN terminal ( page 18).
About the connection illustrations
You can connect different types and brands of devices to
your TV in several different configurations. The connection
illustrations in this manual are representative of typical
device connections only. The input/output terminals on your
devices may differ from those illustrated herein. For details
on connecting and using your specific devices, refer to each
device’s owner’s manual.
Chapter 2: Connecting your TV

Chapter 2: Connecting your TV
13
Connecting a VCR ( or a VCR with S-video) and antenna, Cable TV or
Camcorder
IN
OUT
CH 3
CH 4
IN
from
ANT
VIDEO AUDIO
OUT
to
TV
LR
R
L
OUT
IN
CH 3
CH 4
VIDEO
AUDIO
OUT
L
R
From Cable TV or antenna
You will need:
coaxial cables
standard A/V cables
For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable. Do not connect both types of
video cable to VIDEO 1 at the same time or the picture
performance will be unacceptable.
For better picture performance, if your camcorder has
S-video, connect an S-video cable (plus the audio
cables) to VIDEO 1 on the TV back side instead of the
VIDEO 2 on the TV side panel.
If you have a mono VCR, connect L/MONO on the TV
to your VCR’s audio out terminal using the white audio
cable only.
S-video cable (if your VCR or camcorder has S-video)
Do not connect both types of video cable to VIDEO 1
at the same time or the picture performance will be
unacceptable.
standard audio cables (If you have a mono VCR or
camcorder has S-video)
Note: When you use a Cable box, you may not be able to use
the remote control to program or access certain features on
the TV.
•
•
−
−
−
•
−
•
To view the antenna or Cable signal:
Select the ANT/CABLE video input source on the TV.*
To view basic and premium Cable channels:
Turn OFF the VCR. Select the ANT/CABLE video input
source on the TV.* Tune the TV to channel 3 or 4 (whichever
channel the Cable box output is set to). Use the Cable box
controls to change channels.
To view the VCR:
Turn ON the VCR. Select the VIDEO 1 video input source on
the TV.*
To view the camcorder video:
Select the VIDEO 2 video input source on the TV.*
To select the video input source, press INPUT on the remote control
(page 20). To program the TV remote control to operate other
devices, see Chapter 3.
The unauthorized recording, use, distribution, or revision of television
programs, videotapes, DVDs, and other materials is prohibited under the
Copyright Laws of the United States and other countries, and may subject
you to civil and criminal liability.
*
From Cable TV
S-video cable
or
Standard
A/V cable
Audio cable
Stereo VCR
TV back panel
Camcorder
VIDEO 2 inputs
on TV right side
panel
Cable box

Chapter 2: Connecting your TV
14
Connecting a DVD player with ColorStream®(component video), a VCR,
and a satellite receiver
Your TV has two sets of ColorStream®(component video) inputs.
IN from ANT
VIDEO AUDIO
OUT to TV
LR
R
L
OUT
IN
CH 3
CH 4
VIDEO
OUT
COMPONENT VIDEO
PBPR
Y
AUDIO
OUT
L
R
S-VIDEO
OUT
S-VIDEO
OUT
VIDEO
OUT
AUDIO
OUT
COMPONENT VIDEO
L
R
Satellite
IN
PBPR
Y
You will need:
coaxial cables
standard A/V cables
For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable. Do not connect both types of
video cable to VIDEO 1 at the same time or the picture
performance will be unacceptable.
If you have a mono VCR, connect L/MONO on the TV
to your VCR’s audio out terminal using the white audio
cable only.
standard audio cables
component video cables
You can connect the component video cables (plus
audio cables) from the DVD player or satellite receiver to
either set of ColorStream terminals on the TV (HD-1 or
HD-2). The ColorStream HD-1 and HD-2 terminals can
be used with Progressive (480p, 720p) and Interlaced
(480i, 1080i) scan systems. A 1080i signal will provide
the best picture performance (1080p is not supported).
If your DVD player or satellite receiver does not have
component video, connect a standard A/V cable to
VIDEO 2 on the side panel. If your DVD player has HDMI
video, see page 15.
To view antenna or Cable channels:
Select the ANT/CABLE video input source on the TV.*
To view the DVD player:
Turn ON the DVD player. Select the ColorStream HD-1 video
input source on the TV.*
•
•
−
−
•
•
−
−
To view satellite programs using the component
video connections:
Turn on the satellite receiver. Select the ColorStream HD-2
video input source on the TV.*
To view the VCR or view and record antenna
channels:
Turn ON the VCR. Tune the VCR to the channel you want to
watch. Select the VIDEO 1 video input source on the TV.*
To record a TV program while watching a DVD:
Turn ON the VCR. Tune the VCR to the channel to record.
Select the ColorStream HD-1 video input source on the TV* to
view the DVD.
To select the video input source, press INPUT on the remote control
( page 20). To program the TV remote control to operate other
devices, see Chapter 3.
The unauthorized recording, use, distribution, or revision of television
programs, videotapes, DVDs, and other materials is prohibited under the
Copyright Laws of the United States and other countries, and may subject
you to civil and criminal liability.
*
From antenna
TV back panel
Stereo VCR
DVD player with component video
Satellite receiver with component video
From satellite dish

Chapter 2: Connecting your TV
15
Connecting an HDMI™ or DVI
device to the HDMI input
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI source device,
or uncompressed digital video from a DVI (Digital Visual
Interface) source device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) program material in digital form
from EIA/CEA-861-D–compliant[1] consumer electronic
devices (such as a set-top box or DVD player with HDMI or
DVI output).
The HDMI input can accept and display VGA, SVGA, XGA,
WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz),
1080i (60Hz) and 1080p (24Hz/60Hz) signal formats. For
detailed signal specifications, see page 56.
Supported Audio format: Linear PCM, sampling rate 32/44.1/
48 kHz
Note: To connect a PC to the HDMI input, see page 18.
To connect an HDMI device, you will need:
one HDMI cable (type A connector) per HDMI device
For proper operation, it is recommended that you use an
HDMI cable with the HDMI Logo ( ).
To display an 1080i/60Hz signal format, you will need a
Category 2 cable. Conventional HDMI/DVI cable may
not work properly.
HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration).
See “Setting the HDMI™ audio mode” (page 31).
To view the HDMI device video:
Select the HDMI 1, HDMI 2 or HDMI 3 video input source
on the TV.*
To select the video input source, press INPUT on the remote control
( page 20). To program the TV remote control to operate other
devices, see Chapter 3.
•
−
−
−
−
*
To connect a DVI device, you will need:
one HDMI-to-DVI adapter cable (HDMI type A connector)
per DVI device
For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6.6 ft (2m).
one pair of standard analog audio cables per DVI device
An HDMI-to-DVI adapter cable transfers video only.
Separate analog audio cables are required (see
illustration).
See “Setting the HDMI™ audio mode” (page 31).
VIDEO AUDIO
LR
R
L
OUT
IN
DVI/HDCP
OUT
IN
Note: To ensure that the HDMI or DVI device is reset properly,
it is recommended that you follow these procedures:
When turning on your electronic components, turn on the
TV first, and then the HDMI or DVI device.
When turning off your electronic components, turn off the
HDMI or DVI device first, and then the TV.
[1] EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-
definition video signals. Because this is an evolving technology, it
is possible that some devices may not operate properly with the
TV.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
•
−
•
−
−
•
•
TV back panel
HDMI device
TV back panel
DVI device

Chapter 2: Connecting your TV
16
REGZA-LINK®connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a
REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see page 48.
To connect an Audio Receiver and Playback Devices,
you will need:
HDMI cables ( page 15)
Note:
If several devices are connected, REGZA-LINK feature
may not operate properly.
For proper operation, it is recommended that you use
HDMI cables with the HDMI Logo ( ).
•
•
•
Before controlling the device(s):
After completing the above connections, set the REGZA-
LINK Setup menu as you desire (page 49).
The connected devices must also be set. For details, see the
operation manual for each device.
The REGZA-LINK feature uses the CEC technology as
regulated by the HDMI standard.
This feature is limited to models incorporating Toshiba’s
REGZA-LINK. However, Toshiba is not liable for those
operations. Refer to the individual instruction manuals for
compatibility information.
Note : This feature may not work properly depending on the
devices that are connected.
•
•
•
•

Chapter 2: Connecting your TV
17
Connecting a digital audio system
The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby®*
Digital or 2-channel down-mixed PCM (pulse-code
modulation) signal for use with an external Dolby®Digital
decoder or other external audio system with optical audio
input.
You will need:
optical audio cable (Use an optical audio cable that has
the larger “TosLink” connector and not the smaller “mini-
optical” connector.)
To control the audio:
Turn on the TV and the digital audio device.
Press on the TV’s remote control and open the Audio
menu.
Highlight Audio Setup and press .
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio
Audio Setup
In the Optical Output Format field, select either Dolby
Digital or PCM, depending on your device (“Selecting
the optical audio output format” on page 43).
Done
Audio Setup
Language
Reset
oeretSSTM
English
Dolby Digital
Optical Output Format
HDMI 1 Audio
oNoiduACP
Auto
Dynamic Range Control Compressed
Dolby Digital
Note:
Some audio systems may not be compatible with Dolby
Digital bitstream signals. Older audio systems that are
not compatible with standard optical out signals may
not work properly, creating a high noise level that may
•
1
2
3
4
•
damage speakers or headphones. THIS DAMAGE IS NOT
COVERED BY YOUR WARRANTY.
The DIGITAL AUDIO OUT terminal may not output some
digital audio sources because of copy restrictions.
Manufactured under license from Dolby Laboratories. Dolby and
the double-D symbol are trademarks of Dolby Laboratories.
Connecting an audio system
This connection allows you to use external speakers with an
external analog audio amplifier to adjust the sound level.
You will need:
standard audio cables
LINE IN
LR
To control the audio:
Turn on the TV and the stereo amplifier.
Set up a optimum volume level of the stereo amplifier.
Then you can adjust the sound volume level from the TV’s
volume control or the amplifier’s volume control.
Menu item of Speakers can turn to OFF to mute the TV’s
built in speakers.
•
*
•
1
2
3
TV back panel
TV back panel
Dolby Digital decoder or
other digital audio system
Analog audio amplifier

Chapter 2: Connecting your TV
18
•
Connecting a personal computer
(PC)
With either the PC IN or HDMI connection, you can watch
your computer’s display on the TV and hear the sound from
the TV’s speakers.
To connect a PC to the PC IN terminal on the TV:
When connecting a PC to the PC IN terminal on the TV,
use an analog RGB (15-pin) computer cable and a PC audio
cable.
PC audio
cable
PC audio
output
Conversion adapter
(if necessary)
To use a PC, set the monitor output resolution on the PC
before connecting it to the TV. The PC IN terminal can
accept and display VGA, SVGA, XGA, WXGA and SXGA
signal formats. For detailed signal specifications (page
56).
Other formats or non-standard signals will not be displayed
correctly.
To display the optimum picture, use the PC setting feature
(“Using the PC settings feature” on page 47).
Note:
The PC audio input terminals on the TV are shared with the
HDMI-1 analog audio input terminals (page 48).
Some PC models cannot be connected to this TV.
An adapter is not needed for computers with a compatible
mini D-sub15-pin terminal.
•
•
•
•
•
Depending on the DVD’s title and the specifications of the
PC on which you are playing the DVD-Video, some scenes
may be skipped or you may not be able to pause during
multi-angle scenes.
Signal names for mini D-sub 15-pin connector
Pin No. Signal
name Pin No. Signal name Pin No. Signal name
1 R 6 Ground 11 Reserved
2 G 7 Ground 12 SDA
3 B 8 Ground 13 H-sync
4 Reserved 9 5V 14 V-sync
5 Reserved 10 Ground 15 SCL
To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the TV, use
an HDMI-to DVI adapter cable and analog audio cables.
If connecting a PC with an HDMI terminal, use an HDMI
cable (type A connector). Separate analog cables are not
necessary (page 15).
PC audio
output
PC audio
cable
The HDMI input can accept and display VGA, SVGA, XGA,
WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz),
1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For
detailed signal specifications, see page 56.
Note:
The edges of the images may be hidden.
If receiving a 480i (HDMI), 480p (HDMI), 720p, 1080i, or
1080p signal program, Native mode scales the video to
display the entire picture within the borders of the screen
•
•
•
•
TV back panel
TV back panel
Computer
Computer

19
Preparing the remote control for
use
Your TV remote control can operate your TV and many other
devices such as cable converter boxes, satellite receivers,
VCRs, DVD players, and HTIBs (home theater in a box),
even if they are different brands.
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate most
Toshiba devices (page 23).
If you have a non-Toshiba device or a Toshiba device
that the remote control is not preprogrammed to
operate:
You can program the TV remote control so it will operate the
other device ( pages 21–25).
Installing the remote control
batteries
Remove the battery cover from the back of the remote
control.
Squeeze tab
and lift cover.
Install two “AAA” size batteries, making sure to match
the + and – signs on the batteries to the signs on the
battery compartment.
Reinsert the battery cover in the remote control until the
tab snaps.
Caution: Batteries must not be exposed to excessive heat
such as sunshine, fire or the like.
Note:
Be sure to use AAA size batteries.
Dispose of batteries in a designated disposal area.
Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
1
2
3
•
•
•
•
•
Always remove batteries from the remote control if they
are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
Remote control effective range
For optimum performance, aim the remote control directly
at the TV and make sure there is no obstruction between the
remote control and the TV.
16.4 ft (5m)
Point remote control
toward remote sensor
on front of TV.
•
Chapter 3: Using the remote control

Chapter 3: Using the remote control
20
Learning about the remote control
The buttons used for operating the TV only are described
here. For a complete list of the remote control’s functions, see
the remote control functional key chart ( page 22).
Note: The error message “NOT AVAILABLE” may appear if
you press a key for a function that is not available.
POWER turns the TV on and off. When the TV is on, the
green LED indicator on the TV front will be illuminated.
FREEZE freezes the picture. Press again to restore the
moving picture ( page 39).
SLEEP accesses the sleep timer (page 48).
PIC SIZE cycles through the picture sizes: Natural,
TheaterWide 1/2/3, Full, 4:3 HD, Native and Dot by
Dot (page 37).
Channel Numbers (0–9, –/100) directly tune
channels. The button is used to tune digital channels
(page 36) or to edit the Favorites List (page 34).
INPUT selects the video input source (page 33).
CH ST cycles through programmed channels when no
menu is on-screen (page 29).
VOL + – adjusts the volume level.
FAV BROWSER accesses the Favorites List in the
Channel Brower™ (page 34).
RECALL displays TV status information (page 50).
CH RTN returns to the last viewed channel or source
(page 37).
MUTE reduces or turns off the sound (page 42).
INFO displays TV status information as well as program
details, when available (page 50).
/ While watching TV, these buttons open the
Channel Browser™ and tune to the previous/next channel
in the channel history (page 35). (Also see “Arrow
buttons.”)
Arrow buttons (STWX)When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see / .)
ENTER activates highlighted items in the main menu
system.
MENU accesses the main TV menu system (pages 26
and 27).
EXIT closes on-screen menus.
MODE SELECT switch switches between TV,
CABLE/SAT, AUX 1, and AUX 2 modes (page 21).
Set to “TV” to control the TV.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19